Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for SY Electronics MFT-31C
- Page 1 3 Inputs to 1 HDBaseT Output 2 x HDMI + USB-C to HDBaseT 2 x HDMI + VGA to HDBaseT SY Electronics Ltd., 7 Worrall Street, Salford, Greater Manchester, M5 4TH Tel: +44 (0)161 868 3450 – Fax: +44 (0)161 868 3459 Web: sy.uk...
-
Page 2: Panel Descriptions
RS232 data pass through IR Eye data pass through Built in IR Eye (IR receiver) MFT-31C supports IR learning for Display On/Off control Display On/Off control via RS232 and CEC LED indication for selected input ... - Page 3 HDMI1 & HDMI2 HDMI input ports, connect to HDMI sources USB-C USB Type C input connector - MFT-31C / MFT-31CE only VGA input connector - MFT-31V / MFT-31VE only AUDIO IN Stereo audio input for the VGA input - MFT-31V / MFT-31VE only...
-
Page 4: System Connection
Connection Procedures Connect the HDMI sources to the HDMI 1 and HDMI 2 inputs. For the SY-MFT-31C, any device that has a Type C USB connector may be connected to the USB-C input. For the SY-MFT-31V, any device that has a VGA connector may be connected to the VGA input, together with associated Audio. - Page 5 Connect the 24V DC PSU to the MFT-31 or it can be powered from the appropriate HDBaseT receiver (with PoC). If required, an RS232 controller may be connected to the rear of the MFT-31 to control the MFT-31 as well as for control of the remote display device. If required, an IR Eye may be connected to the rear of the MFT-31 to control the remote display device.
-
Page 6: Ir Pass-Through
Where: x is the baud rate for the display device: 0 = 2400 1 = 4800 2 = 9600 3 = 19200 4 = 38400 5 = 57600 6 = 115200 aa is the ASCII command to turn the display on ... -
Page 7: Input Selection
MFT-31C IR Learning Feature The MFT-31C / CE feature IR learning of the Display On/Off button commands: Press and hold both the DISPLAY ON/OFF and SELECTION / AUTO buttons until the both the button LEDs flash alternately. Use the DISPLAY ON/OFF button to choose the command to be set:... -
Page 8: Edid Management
The input resolution (EDID setting) can be set using RS232 commands to one of the options given in the following table. Please note that the EDID setting commands are used differently for the MFT-31C and MFT-31V models. Preferred Input Video... -
Page 9: Cec Commands
Please note that only CEC enabled devices that have the specified logical address will respond to CEC commands. CEC Command RS232 Command Volume Up (MFT-31C only) 50730% Volume Down (MFT-31C only) 50731% Volume Mute Toggle (MFT-31C only) 50732% Display On 50733% Display Off 50734% Send Specific CEC Command CEC<xx:xx:xx:…>... -
Page 10: Product Part Numbers
Get VGA Audio Mute Status 50728% Control Port Baud Rate The VGA versions of the MFT-31 also provide the following baud rate options for the RS232 control port. (The MFT-31C/MFT-31CE is fixed at 9600 baud only). Control Port Baud Rate RS232 Command 2400... -
Page 11: Specifications
5W max. (MFT-31 only – add extra for HDBaseT receiver) Environmental Operating Temperature -10 to +40°C (+14 to +104°F) Operating Humidity 10 to 90 % RH (non-condensing) MFT-31C / 31CE: 235g Weight MFT-31V / 31VE: 245g Physical Dimensions (WxHxD) UK: 146 x 86 x 43mm... -
Page 12: Safety Instructions
Damage to the product due to incorrect usage or storage Damage caused by unauthorised repairs Damage caused by mistreatment of the product Please direct any questions or problems you may have to your local dealer before contacting SY Electronics. sy.uk V1.1...
Need help?
Do you have a question about the MFT-31C and is the answer not in the manual?
Questions and answers