Download
Share
Print this page
Velleman THE TREMOR Assembly Manual
  1. Manuals
  2. Brands
  3. Velleman Manuals
  4. Music Pedal
  5. THE TREMOR
  6. Assembly manual
Velleman THE TREMOR Assembly Manual

Velleman THE TREMOR Assembly Manual

Tremolo effect pedal
Hide thumbs Also See for THE TREMOR:

Advertisement

Quick Links

Download this manual
ASSEMBLY MANUAL
MAY 2016
THE TREMOR - TREMOLO EFFEcT PEDAL
ORDERcODE: K8110
W W W . V E L L E M A N P R O J E C T S . E U

Advertisement

loading
Need help?

Need help?

Do you have a question about the THE TREMOR and is the answer not in the manual?

Questions and answers

Related Manuals for Velleman THE TREMOR

Summary of Contents for Velleman THE TREMOR

  • Page 1 ASSEMBLY MANUAL MAY 2016 THE TREMOR - TREMOLO EFFEcT PEDAL ORDERcODE: K8110 W W W . V E L L E M A N P R O J E C T S . E U...
  • Page 2 Table of contents What’s in the box Assembly instructions Let’s get started!

  • Page 3: What's In The Box

    WHAT’S IN THE BOX ASSEMBLY MANUAL K8110...
  • Page 4 ASSEMBLY INSTRUcTIONS 1. Place the 2 supplied cover stickers as shown in the images below. Note the orientation of the bottom cover! ASSEMBLY MANUAL K8110...
  • Page 5 2. All resistors are placed in the correct order of usage on the supplied tape. Resistors: R1 to R19 Tape order: R12:4K7 R13:47K R1:330K R14:33K R2:470K R15:10K R3:330K R16:39K R4:470K R17:100K R5:390E R18:100E R6:10K R19:1M R7:100K C3:104 R8:470E C4:104 R9:470E C9:104 R10:1M ZD1:3V3...
  • Page 6 3. 100 µF axial capacitors: C3, C4 and C9 4. 2 x Ic: U1 and U2 Note the orientation of the Ic’s! ASSEMBLY MANUAL K8110...
  • Page 7 5. Zenerdiode: ZD1 Note the orientation of the zenerdiode! ZD... ASSEMBLY MANUAL K8110...
  • Page 8 6. Male connectors: SW1; SW2, RV1; RV2 and RV3 7. Diode: D1 ASSEMBLY MANUAL K8110...
  • Page 9 8. Bc547: T1 Bc557: T2 9. capacitor 471: C1 ASSEMBLY MANUAL K8110...
  • Page 10 10. capacitor 473: C6 11. capacitor 105: C11 ASSEMBLY MANUAL K8110...
  • Page 11 12. Follow these steps: A. Bend the pins of the 3mm white LED as shown in the pictures below. B. Cut a 7mm piece of 2.4mm shrinktube. ASSEMBLY MANUAL K8110...
  • Page 12 C. Slide both the 3 mm white LED and the 3 mm photo transistor in the shrink tube as shown below. No need to actually shrink the tube. This will act as the lightbridge. D. Place and solder this assembly in LD2 and P1. Note the orientation of both cathode pins! ASSEMBLY MANUAL K8110...
  • Page 13 13. Dc jack: J1 14. capacitor 10µF: C14 Note the polarity! ASSEMBLY MANUAL K8110...
  • Page 14 15. 2 x Audio jack: SK1 and SK2 16. 5 mm blue LED: LD1 (do a diode test with a multimeter to find the blue LED) Note the polarity! Make sure it stands out about 12 mm from the PcB, as shown in the picture! C (-) ASSEMBLY MANUAL K8110...
  • Page 15 17. 5 mm white LED: LD3 (do a diode test with a multimeter to find the white LED) Note the polarity! Make sure it stands out about 12 mm from the PcB, as shown in the picture! ASSEMBLY MANUAL K8110...
  • Page 16 Turn the PcB around! 18. capacitor 220 µF: C2 Note the polarity! Solder on the bottom side of the PcB! 18. capacitor 10 µF: C5, C7, C8, C12 Note the polarity! Solder on the bottom side of the PcB! ASSEMBLY MANUAL K8110...
  • Page 17 20. capacitor 47 µF: C10 Note the polarity! Solder on the bottom side of the PcB! 21. capacitor 100 µF: C13 Note the polarity! Solder on the bottom side of the PcB! ASSEMBLY MANUAL K8110...
  • Page 18 22. Trim the leads on the 9 V snapt to 5 cm. 22. Strip and tin both wires ASSEMBLY MANUAL K8110...
  • Page 19 23. Place and solder the 9 V snap to the PCB as shown in the images below. Note the polarity! RED = +, BLAcK = - ASSEMBLY MANUAL K8110...
  • Page 20 ASSEMBLY MANUAL K8110...
  • Page 21 23. Slide 4,5 cm of the biggest shrinktube over the connector. When no battery is used in the pedal this cover should always be used. ASSEMBLY MANUAL K8110...
  • Page 22 24. Place the finished board into the pedal casing and tighten it down with the supplied screws. ASSEMBLY MANUAL K8110...
  • Page 23 25. Shorten all the pins on the footswitch by 1.5 - 2 mm. 26. Install the footswitch as shown in the images below. ASSEMBLY MANUAL K8110...
  • Page 24 ASSEMBLY MANUAL K8110...
  • Page 25 27. Install the selector switch as shown in the images below. ASSEMBLY MANUAL K8110...
  • Page 26 28. Install the 2 potentiometers as shown in the images below. Note the placement of the different values! ASSEMBLY MANUAL K8110...
  • Page 27 29. Trim the leads of the 6 wire female connector to 4.5 cm. ASSEMBLY MANUAL K8110...
  • Page 28 30. Strip and tin the wires. 31. Cut 6 x 7 mm pieces of the 2.4 mm shrinktube. ASSEMBLY MANUAL K8110...
  • Page 29 32. Solder the wires to the footswitch as shown below. Do not forget the shrinktube pieces and note the colors. ASSEMBLY MANUAL K8110...
  • Page 30 33. Trim the leads of the 2 wire female connector to 4.5 cm. ASSEMBLY MANUAL K8110...
  • Page 31 34. Strip and tin the wires. 35. Cut 2 x 7 mm pieces of the 2.4 mm shrinktube. ASSEMBLY MANUAL K8110...
  • Page 32 36. Solder the wires to the footswitch as shown below. Do not forget the shrinktube pieces and note the colors. 37. Trim the leads of one of the 3 wire female connector to 4.5 cm. ASSEMBLY MANUAL K8110...
  • Page 33 38. Strip and tin the wires. 39. Cut 3 x 7 mm pieces of the 2.4 mm shrinktube. ASSEMBLY MANUAL K8110...
  • Page 34 40. Solder the wires to the selector switch as shown below. Do not forget the shrinktube pieces and note the colors. ASSEMBLY MANUAL K8110...
  • Page 35 41. Trim the leads of two of the 3 wire female connector to 5 cm. 42. Strip and tin the wires of both connectors. ASSEMBLY MANUAL K8110...
  • Page 36 43. Cut 6 x 7 mm pieces of the 2.4 mm shrinktube. 44. Solder the wires to the 500K and the B10K potentiometer as shown below. Do not forget the shrinktube pieces and note the colors. ASSEMBLY MANUAL K8110...
  • Page 37 45. Trim the leads of one of the 3 wire female connector to 7 cm. 46. Strip and tin the wires of the connector. ASSEMBLY MANUAL K8110...
  • Page 38 47. Cut 3 x 7 mm pieces of the 2.4 mm shrinktube. 48. Solder the wires to the B100K potentiometer as shown below. Do not forget the shrinktube pieces and note the colors. ASSEMBLY MANUAL K8110...
  • Page 39 49. Slide the 3 knobs on top of the potentiometers. 50. Plug all the connectors onto their correct plug and close the enclosure. ASSEMBLY MANUAL K8110...
  • Page 40 Plug in your gear and play! ASSEMBLY MANUAL K8110...
  • Page 41 VellemanProjects @Velleman_RnD ORDERCODE: K8110 VELLEMAN nv - Legen Heirweg 33, Gavere (Belgium) REVISION: HK8110 vellemanprojects.com...