Subscribe to Our Youtube Channel
Summary of Contents for RVR Solar EasyStove
- Page 1 EasyStove Hydraulic interface unit for solid fuel systems Installation, Usage and Maintenance Instructions 20170412...
-
Page 2: Table Of Contents
Hydraulic connection ..........................9 08. Electrical connection ...........................10 Power supply ............................10 Connection to solid fuel boiler ......................11 Schematic ...............................11 09. Commissioning ..............................12 Circulation Control ..........................12 10. Maintenance and troubleshooting ......................13 Spare Part List ..............................13 Installation, Usage and Maintenance Instructions EasyStove... -
Page 3: General Information
Thank you for selecting an EasyStove interface unit. This product is the result of extensive research and experi- ence in heating system design. This manual is an integral part of the product and should be retained. Please read it carefully, as it provides important information regarding the installation and maintenance of the product. -
Page 4: Technical Information
Weight incl. Cover 11.0 kg PRINCIPAL COMPONENTS Heat Exchanger System Pump Air Vent Stove Circuit Pump Electrical Box Non Return Valve Cover Flow to System Return from System Return to Stove Flow from Stove Installation, Usage and Maintenance Instructions EasyStove... -
Page 5: Heat Exchanger Characteristics
HEAT EXCHANGER CHARACTERISTICS The EasyStove is designed for use with solid fuel stoves with a combustion output* of up to 20kW (max output to water* of 14kW) At Nominal Capacity Primary Stove Circuit Secondary Heating Circuit Flowrate L/h Temperature °C IN/OUT... -
Page 6: Important Points
The 230V, 50Hz power supply must be protected by a suitable MCB. A flue thermostat must be mounted on the solid fuel boiler/stove and connected as a volt-free contact to the EasyStove. The ESBE CTF150 model flue thermostat is supplied with the EasyStove. SAFETY WARNINGS... -
Page 7: System Layout
The scheme below will suit many systems. It takes account of the fundamental requirements outlined above. Some stoves and boilers will have a heat dissipation facility but if this is not present, the EasyStove heat dis- sipation kit should be installed as shown. The heat dissipation kit should be installed on the feed and expan- sion pipes as indicated. -
Page 8: Dimensions
WALL MOUNTING The EasyStove is normally supplied without a cover. If the unit is equipped with a cover, it should be re- moved and placed in a safe place. The cover is attached to the frame using four screws, two on the top and two on the bottom. -
Page 9: Mounting Of Flue Thermostat
The installer should check all connections and tighten them if necessary to restore the compression of the gasket. The installer is responsible for ensuring that the entire system is watertight. NOTE Ensure thorough flushing of the system, to eliminate dirt, before commissioning. Installation, Usage and Maintenance Instructions EasyStove... -
Page 10: Electrical Connection
The electrical installation must be carried out by a qualified electrician. The equipment must be installed in accordance with IEE and all other relevant regulations. The EasyStove requires a 230 volts, 50Hz, single phase power supply. The power supply must be protected by a suitable MCB. -
Page 11: Connection To Solid Fuel Boiler
On increase of the temperature of the solid fuel boiler/stove, the TCcom -TCno contacts will move from CLOSED to OPEN. SCHEMATIC ESBE CTF150 Flue Thermostat RELE Pcam Fuse 1A Pcam Pcal Solid Fuel Pcal Stove 2. N/C contact max.16(2.5)A, 230VAC 4. N/O contact max.6.3(2.5)A, 230VAC Installation, Usage and Maintenance Instructions EasyStove... -
Page 12: Commissioning
09. COMMISSIONING Before operating the equipment, ensure that all air is purged from the EasyStove using the appropriate manual air vents and that the pump impeller of the pump is free to rotate. Ensure that all air is purged from the EasyS- tove Heat Dissipation kit (if used). -
Page 13: Maintenance And Troubleshooting
Maintenance and repair work must be performed by experienced technicians only. Disconnect the power supply before carrying out any work on the equipment. The EasyStove must be inspected annually to ensure correct operation and the absence of leaks. A record of the annual inspection should be preserved. - Page 14 Contact us: RVR Energy Technology Limited Kenmare Co. Kerry V93 F386 Ireland Sales direct line: +353 (0)64 6689522 Email: sales@rvr.ie...
Need help?
Do you have a question about the EasyStove and is the answer not in the manual?
Questions and answers