Office Star Products Air Grid Operating Instructions

FAUTEUIL DE DIRECTEURS
PROFESSIONNEL AU DOSSIER à MAILLES AÉRÉES
INSTRUCTIONS DE MONTAGE
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et
s'assurer que les quantités des pièces reçues sont correctes.
ÉTAPE 1 Insérer les cinq roulettes (2) dans la base (1) et pousser fort jusqu'à ce que chaque roulette (2)
s'encliquette.
ÉTAPE 2 Attacher les bras (7L et 7R) au coussin du siège (5) en utilisant six vis longues à tête Phillips (8) et six
rondelles plates (9). RESSERRER COMPLÈTEMENT LES VIS.
ÉTAPE 3 Attacher la plaque du siège (4) au coussin du siège (5) avec la flèche orientée vers l'avant du fauteuil en
utilisant quatre vis courtes à tête Phillips (10). RESSERRER COMPLÈTEMENT LES VIS.
ÉTAPE 4 Attacher le support du dossier (12) à la plaque du siège (4) en utilisant trois vis Allen (11). RESSERRER
COMPLÈTEMENT LES VIS EN UTILISANT LA CLÉ ALLEN (13).
ÉTAPE 5 Avec la base (1) debout et les roulettes (2) sur le plancher, insérer le vérin pneumatique (3) dans la
base (1). Placer le siège assemblé sur le dessus du vérin pneumatique (3) et pousser la pression vers le bas.
ATTENTION : VÉRIFIER QUE TOUS LES VIS SONT INSTALLÉS ET BIEN SERRÉS AVANT DE L'UTILISER.
ÉTAPE 1
8
1
2
x5
9
7R
ÉTAPE 4
13
11
x3
12
4
2
6
PIÈCE
1. Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Roulette . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Vérin pneumatique . . . . . . . . . . . . . . . . . . . . 1
4. Plaque de siège . . . . . . . . . . . . . . . . . . . . . . 1
5. Coussin du siège . . . . . . . . . . . . . . . . . . . . . 1
6. Coussin du dossier . . . . . . . . . . . . . . . . . . . 1
7. Bras gauche (7L) et droit (7R) . . . . . . . . . . . 2
8. Vis longues à tête Phillips (bras) . . . . . . . . . 6
9. Rondelle plate (bras) . . . . . . . . . . . . . . . . . . 6
10. Vis courtes à tête Phillips (plaque du siège) 4
11. Vis Allen (support du dossier) . . . . . . . . . . 3
12. Support du dossier . . . . . . . . . . . . . . . . . . 1
13. Clé Allen . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ÉTAPE 2 ÉTAPE 3
10
x3
8
x3
x3
9
x3
7L
5
ÉTAPE 5
5
3
1
QTÉ
3
x4
4
1
5
LIMITED WARRANTY
C hairs are warranted* from the date of purchase against failure due to material and workmanship as follows:
• Lifetime on component parts including pneumatic cylinder, control mechanism, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons
weighing 250 lbs. or less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism,
rusting, acts of nature or any other event beyond the control of us. The warranty does not cover cosmetic damage that may result from normal
use. Liability for incidental or consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When
usage is more than 40 hours per week, a five year warranty on all parts applies. Fabric is warranted for one year.
To make a warranty claim, contact Parts Department via e-mail. Pacific Time. Provide model number and description of the
problem and obtain confirmation number.
(a) Supply compatible components of current manufacture.
(b) Repair the customer's component.
It is the customer's responsibility to prepay freight on any components returned to the factory. Return freight on components
covered by warranty will be paid.
AIR GRID BACK
PROFESSIONAL MANAGERS CHAIR
OPERATING INSTRUCTIONS
FEATURE
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever (1) up.
To lower seat height sit on chair and lift lever (1) up.
NOTE: It is normal for chair to slightly lower under body weight.
• 2-TO-1 SYNCHRO TILT ADJUSTMENT
For individual comfort, this chair has been equipped with an
adjustment that will allow the user to change the tension of
the tilting feature. Turn knob (2) clockwise to increase tension
and counter-clockwise to decrease or ease the tension. To lock
return chair to the upright position, push lever (1) in. To unlock
pull lever (1) out.
NOTE: Be careful not to loosen back tilt adjustment knob
completely.
• ARM HEIGHT ADJUSTMENT
To adjust arm height, push button (3) in to allow the arms
to move up or down freely. Release the button (3) once the
desired height is reached.
2
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and knobs
are securely tightened.
3. Check that all bolts screws and knobs are tight every
three months or as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic
cover as head covering. It may cause suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.
At it's option we will: