Table of Contents
Advertisement
Quick Links
Issued on 01/10/14
R. 04
This manual is integrant and essential to the product. Carefully read the instructions contained herein as they provide important
•
hints for use and maintenance safety.
This device is to be used only for the purposes it has been designed to. Other uses should be considered improper and dangerous.
•
The manufacturer is not responsible for possible damages caused by improper, erroneous and irrational uses.
Elettronica Santerno is responsible for the device in its original setting.
•
Any changes to the structure or operating cycle of the device must be performed or authorized by the Engineering Department of
•
Elettronica Santerno.
Elettronica Santerno assumes no responsibility for the consequences resulting by the use of non-original spareparts.
•
Elettronica Santerno reserves the right to make any technical changes to this manual and to the device without prior notice. If
•
printing errors or similar are detected, the corrections will be included in the new releases of the manual.
The information contained herein is the property of Elettronica Santerno and cannot be reproduced. Elettronica Santerno enforces
•
its rights on the drawings and catalogues according to the law.
Contents
1
About This Manual ..................................................................................................................................................... 2
2
Caution Statements.................................................................................................................................................... 2
2.1
Electrical Shock Risk .....................................................................................................................................................................2
2.2
System Design and Safety of Personnel.......................................................................................................................................3
2.3
STOP function ...............................................................................................................................................................................3
2.4
Disposal Instructions .....................................................................................................................................................................3
3
Introduction ................................................................................................................................................................ 3
3.1
Feature List ...................................................................................................................................................................................3
4
The Keypad ................................................................................................................................................................. 4
4.1
Starter Status LEDs ......................................................................................................................................................................4
5
Installation .................................................................................................................................................................. 4
5.1
Physical Installation .......................................................................................................................................................................4
5.2
Control Terminals ..........................................................................................................................................................................5
5.3
Control Voltage..............................................................................................................................................................................5
5.4
Control Wiring................................................................................................................................................................................5
5.5
Power Terminations ......................................................................................................................................................................6
5.6
UL Compliant Installation ..............................................................................................................................................................6
5.7
Schematic Diagrams .....................................................................................................................................................................7
6
How to configure the ASAB ...................................................................................................................................... 8
6.1
Programming Menu .......................................................................................................................................................................8
7
Operation .................................................................................................................................................................... 9
7.1
Start, Stop and Reset Commands ................................................................................................................................................9
7.2
Using the Soft Starter to Control a Motor ......................................................................................................................................9
8
Specifications ............................................................................................................................................................. 9
8.1
Model Code .................................................................................................................................................................................10
- 15V0078B1 -
ASAB
ADVANCED SOFT STARTER
QUICK SETUP GUIDE
Elettronica Santerno S.p.A.
Via della Concia 7, 40023 Castel Guelfo (BO) Italy
Tel. +39 0542 489711
www.santerno.com, info@santerno.com
-
Fax +39 0542 489722
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CARRARO SANTERNO ASAB
Summary of Contents for CARRARO SANTERNO ASAB
-
Page 1: Table Of Contents
- 15V0078B1 - ASAB ADVANCED SOFT STARTER QUICK SETUP GUIDE Issued on 01/10/14 R. 04 This manual is integrant and essential to the product. Carefully read the instructions contained herein as they provide important • hints for use and maintenance safety. This device is to be used only for the purposes it has been designed to. -
Page 2: About This Manual
About This Manual This manual provides brief information to assist in installing and operating the ASAB in simple applications. For comprehensive information on installing and operating the ASAB, refer to the ASAB User Manual (available from santerno.com). The examples and diagrams in this manual are included solely for illustrative purposes. The information contained in this manual is subject to change at any time and without prior notice. -
Page 3: System Design And Safety Of Personnel
System Design and Safety of Personnel The starter is intended as a component for professional incorporation into complete equipment or a system. If installed incorrectly, the starter may present a safety hazard. The starter uses high voltages and currents, carries stored electrical energy, and is used to control equipment which can cause injury. Close attention is required to the electrical installation and the system design to avoid hazards either in normal operation or in the event of equipment malfunction. -
Page 4: The Keypad
The Keypad Four-line display for status and programming details. LOCAL/REMOTE: Toggle between Local and Remote control STATUS: Open the status displays and scroll between different status screens GRAPHS: Open the performance graphs and scroll between different graph screens LOGS: Open the logs Soft starter local control buttons Local START: Start the motor... -
Page 5: Control Terminals
Control Terminals Control terminations use 2.5mm plug-in terminal blocks. Unplug each block, complete the wiring, then reinsert the block. 13 14 21 22 24 33 34 13 14 21 22 24 33 34 13 14 21 22 24 33 34 A4 A5 A6 A4 A5 A6 40 41 53 54 55 56 57 58 64 65... -
Page 6: Power Terminations
Power Terminations NOTE For personnel safety, the power terminals on models up to ASAB-0105B are protected by snap-off tabs. When using large cables, it may be necessary to break off these tabs. NOTE Some units use aluminium busbars. When connecting power terminations, we recommend cleaning the surface contact area thoroughly (using an emery or stainless steel brush) and using an appropriate jointing compound to prevent corrosion. -
Page 7: Schematic Diagrams
Schematic Diagrams Internally bypassed models Non-bypassed models 2/T1 1/L1 1/L1 2/T1 3/L2 4/T2 3/L2 4/T2 5/L3 6/T3 5/L3 6/T3 24 VDC 24 VDC 200 mA 200 mA Control voltage (model dependent) 54, 55 Start Remote control inputs 56, 57 Stop Motor thermistor input 58, 57 Reset... -
Page 8: How To Configure The Asab
How to configure the ASAB Open the programming menu. Scroll to Quick Setup Menu, then select your application. Adjust each parameter to match your motor and application. Programming Menu You can access the Programming Menu at any time, including while the soft starter is running. Any changes to the start profile take effect immediately. -
Page 9: Operation
Display 10A Language English 10B User Screen - Top Left Starter State 10C User Screen - Top Right Blank 10D User Screen - Bottom Left Hours Run 10E User Screen - Bottom Right Blank 10J Display A or kW Current For a full list of all parameters in the ASAB Extended Menu, refer to the ASAB User Manual, available from santerno.com. -
Page 10: Model Code
Stop (56, 57) ..................................Normally Closed Reset (58, 57) .................................. Normally Closed Programmable input (53, 55) ............................. Normally Open Motor thermistor (64, 65) ..........................Trip >3.6 kΩ, reset <1.6kΩ Outputs Relay outputs ....................... 10A @ 250 VAC resistive, 5A @ 250 VAC AC15 pf 0.3 Programmable outputs Relay A (13, 14) ..............................
Need help?
Do you have a question about the SANTERNO ASAB and is the answer not in the manual?
Questions and answers