Summary of Contents for Innova iTroll Generation 2
- Page 1 iTroll Precision Throttle Controller www.iTroll.us Made in USA Generation 2 Owner’s Manual Software Version: OS6.0 “T. H.” - Lake Erie “Al H.” - Columbia River, OR...
-
Page 2: Table Of Contents
The iTroll story started when an avid fisherman was not satisfied with the unreliable and simplistic products that were available at the time. As the owner of a company that designed and manufactured electronics, he decided to create a throttle controller that met his personal standards for RELIABILITY, INNOVATION AND SAFETY. -
Page 3: Product Introduction / Safety Notices
Thank you for purchasing iTroll, the most innovative throttle controller to be unleashed on unsuspecting fish! A partial list of iTroll’s industry first features include a fully weatherproof enclosure, 32 character lighted display, 1000 throttle positions, last idle recall, secondary cruising speed (SCS), DRAG Mode and the ability to control two motors. -
Page 4: Turning Itroll On & Off
Display Notice iTroll has prompts on it’s display to aid you in operating it. A DOWN ARROW (â) in front of a button name means to press that button. EXAMPLE: âHunt means “Press the Hunt Button” Section 1: Turning iTroll On and Off Turn iTroll On: Press Button. -
Page 5: Manual Mode To Hunt Mode
2.9: Hunt Enabled iTroll’s only - Enter HUNT Mode by: A) First idling the motor by pressing the Idle button. B) Enter HUNT Mode by pressing the Hunt button. See Section 4 for HUNT Mode Description / Operation Section 3: iTroll’s Special Features 3.1: “SCS”... -
Page 6: Optional Remote Idle / Run Switches
Once unlocked, HUNT Mode is permanently enabled for the life of your iTroll. Call your dealer or Innova (maker of iTroll) at (909) 971-0000 to purchase an unlock code. Please note that unlocking HUNT Mode is performed in the field and takes just a few minutes. - Page 7 In comparison, an iTroll running in HUNT Mode is literally stalking the fish and taking an ACTIVE role in your angling success. It’s no wonder that an iTroll in HUNT Mode is considered to be “The Deadliest Tool in Fishing”! HUNT Mode runs three unique types of throttle sequences: 4.2: Stepping (Searching) Programs: You program low and high throttle settings and iTroll will step up and down between...
-
Page 8: Hunt Mode User Interface
HUNT Mode program memory: iTroll stores EIGHT individual HUNT programs in internal memory. You can now have HUNT programs for different conditions (example: fishing up wind or down wind), or for different baits / presentations (example: bottom bouncers vs. stick baits). The memory positions are allocated as follows: FOUR for stepping programs, and TWO EACH for cut and bump programs (4 + 2 + 2 = 8 total). -
Page 9: Hunt Mode Operation
Stepping / Searching Programs: Cut Throttle Programs: Memory addresses A - D (see M, below): Memory addresses e - f S1 S2 10-20% 3.0% 1m 0% - 10s 15% - 1m 1e 0.0% Ç 0:04 1A 16.0% Ç 0:15 BUMP Throttle Programs: Memory addresses G - H 15% - 1m 20% - 10s 1G 15% Ç... - Page 10 If using HUNT Mode for the first time, you must set Hunt’s safety limits for your particular boat - see sections 8 AND 9. Additionally, the Hunt parameters initially programmed into your iTroll are very conservative and will most likely need to be reprogrammed (step 6.3 below).
-
Page 11: Reprogramming Hunt Parameters
Section 7: Reprogramming HUNT Parameters CAUTION! NEVER use a step size between throttle settings that may cause the boat to accelerate or decelerate to a degree that can cause occupant(s) to lose their balance! Parameter Reprogramming Screen Operation When reprogramming mode, four menus are presented (one for each parameter that is in a given HUNT program). -
Page 12: Hunt Safety Limits 11
7.4: Parameter menus for Cut Memory addresses 1e - 1f and 2e - 2f: Menus are presented in this order in the programming sequence: CutSpeed | CutSpeed Time (in Seconds) | TrollSpeed | TrollSpeed Time (in Minutes). 7.5: Parameters for Bump Memory addresses 1G - 1H and 2G - 2H: Menus are presented in this order in the programming sequence: TrollSpeed | TrollSpeed Time (in Minutes) | BumpSpeed | BumpSpeed Time (in Sec- onds). -
Page 13: Turning Drag Mode On Or Off
9.1: The menu to reprogram the HUNT Low and High limits are a side menu when you program iTroll’s regular parameters. Simply follow the steps in Section 7 and make sure perform Step 7.1A. 9.2: Turn dial to enter HLL (Hunt Low Limit), store value by pressing Hunt button. -
Page 14: Dual Motor Capability
Section 12: Optional Dual Motor Control Dual Motor Mode is a software upgrade that is in every iTroll. When dual motor enabled, iTroll can control two motors on the same boat. These motors can be a kicker and a main or a pair of mains on a boat with twin outboards. -
Page 15: Rapid Off
Flickering indicates that you are between two numbers and will result in an invalid entry. Press the Hunt button to enter the number, screen will read “Lock #2”. 13.7: Repeat step 13.6 to enter all four numbers in the unlock combination. 13.8: If you see the message “Invalid Combo”, repeat Steps 13.4 - 13.7. - Page 16 Innova makes no warranty as to the fitness of the product for any particular purpose or use. The extent of Innova's liability under this limited warranty is the repair or replacement provided above and, in no event , shall Innova's liability exceed the purchase price paid by the purchaser of the product.
Need help?
Do you have a question about the iTroll Generation 2 and is the answer not in the manual?
Questions and answers
My key pad for my Itroll gen delaminated. Can I order replacement keypad