Subscribe to Our Youtube Channel
Summary of Contents for Blu TEE005
- Page 1 TEE005 Installation & User Manual TEE005 NETLEVEL - Module Point to point and Server connection 2017-06 1 866 907 0122 blubathworks.com...
-
Page 2: Installation Requirements
If further assistance is required, please contact: Product Support at 1.866.907.0122 (09:00 – 17:00hrs PST) or email technical@blubathworks.com North America Blu Bathworks Inc. 188 Smithe Street,Vancouver, BC, Canada, V6B 6A9 T +1.604.299.0122 F +1.604.299.0125 Please refer to blubathworks.com for warranty, terms & conditions under warranty & procedure for warranty service. - Page 3 MAX 33 ft [10m]: If distance - TEE030 is exceeding 33ft [10m], - TEE030S set up a Repeater between - TEE030SV devices WLAN Wi-Fi Module Repeater TEE005 Supported Security: WPA & WPA2 Open MAX 66 ft Not Supported Security: [20m] WPA/WPA2 Enterprise iPhone/iPad Router 2017-06 1 866 907 0122 blubathworks.com...
- Page 4 Compatible Control Mixers TEE030 - 2 outlet - Tub filler/Handshower TEE030S - 2 outlet - Shower/Handshower TEE030SV - 3 outlet - Shower/Handshower/Body Jets 2017-06 1 866 907 0122 blubathworks.com...
- Page 5 Note location, password and serial number Location Password (PW): Serial Number (SN): Location Password (PW): Serial Number (SN): Location Password (PW): Serial Number (SN): Location Password (PW): Serial Number (SN): 2017-06 1 866 907 0122 blubathworks.com...
- Page 6 Netlevel Introduction and important notes Compatibility and using this guide: The IoT module is compatible with most ‘smart devices’ with a web browser app. This installation guide uses an iPad and a Galaxy Tab to demonstrate the installation and setup procedures.
-
Page 7: Installation
Installation Install the Netlevel module 1. Stick the WLAN module on the designated place between battery and AC adapter. 2. Connect t with the controller at the port DISPLAY*. *as the case maybe this port could be marked RS-232 or WLAN. Connect your Device (example shown: iPad ®... - Page 8 STEP 3 STEP 4 Enter Password Open your Web Browser (The password is printed on the side of the module) STEP 5 STEP 6 Enter URL: Operate your Twinlevel device as per the instructions on page 10 1.1.1.1 2017-06 1 866 907 0122 blubathworks.com...
- Page 9 Connect your Device (example shown: Galaxy Tab S ® STEP 1 STEP 2 Start Settings App Go to Wi-Fi Settings and choose your device’s network tlc-serial number (SN) (The serial no. is printed on the side of the module) STEP 3 STEP 4 Enter Password Open your Web Browser...
- Page 10 Connect your Device (example shown: Galaxy Tab S ® STEP 5 STEP 6 Operate your Twinlevel device as Enter URL: per the instructions on page 10 1.1.1.1 Connect your Device to your Network Select [Network] Then choose your network Enter the password of your network Afterwards the device will connect automatically with the webserver.
- Page 11 Home - Operate your Device To start and stop the water flow press once on the temperature knob. To adjust the temperature and flow with the according knob by turning it clock or counter clock wise. The temperature and flow rate will show on the icons. To open and close the drain, press on the drain-button (top-right corner) 2017-06 1 866 907 0122...
-
Page 12: Manual Filling
Manual Filling To start and stop the water flow press once on the temperature knob. To adjust the temperature and flow with the according knob by turning it clock or counter clock wise. The temperature and flow rate will show on the icons. -
Page 13: Quick Access
Quick Access 3 Quick Access are programmable. You need to program them on the interface at the bathtub. (consult your Twinlevel interface user manual) Afterwards, select [Fill bathtub] to automatically fill your bathtub. Once the filling has started a [Cancel] button will show. - Page 14 Hygiene To activate the Hygiene flush move the switch to the right You can choose the flush settings Select [Start disinfection] to start the To manually stop the disinfection according to your needs: disinfection process. process at any time, press [Cancel disinfection] Repetition period &...
-
Page 15: Function Test
Function Test If the divice does not work, press [Start Function Test] Answer all the questions and follow the instrucitons. (For this you need to stand next to your interface) Settings Choose the [Temperature unit] in °C or °F You can rename your device if you press on [TWINLEVEL] Press [Reboot], to reboot the device if necessary 2017-06... - Page 16 Network Information about your network If your network isn’t working, you may activate the Peer-to-Peer-mode, like that you are sill able to control your device after you connected your tablet, according to the instruction “Connect your device” Step 2-5. To connect again with your home-network, delete the device from your device-overview. Repeat the steps according to the instruction “Add a new device”.
Need help?
Do you have a question about the TEE005 and is the answer not in the manual?
Questions and answers