Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
MAXI WALL HUNG SERIES
1. Determine the back bar's height. Standard wardrobes usually work best at a finished height of 2m from the floor
(finished height is the height from the top side of the top shelf to the floor). The back bar needs to be installed
150mm lower than your desired finished height. If you want your wardrobe system to have a finished height of
2m from the floor, you will need to set the back bar height at 1850mm from the floor. Measure the width of the
wardrobe at this height and cut the rail and white cover to size.
Using a spirit level, mark out the holes, ensuring you are installing the back bar into wall studs wherever possible.
Use a 5mm drill bit and secure the back bar with screws provided.
2. Once the back bar is secure, add the white bar cover using moderate force, this clips over the back bar to hide
the fittings behind.
3. Fit brackets on to inside of panels.
Suspension Brackets come in Left and Right.
Ensure hook is facing back and is right way up.
First insert sleeves into the 2 holes as shown.
Suspension Bracket
Screws
Sleeves
Advertisement
Related Manuals for Wardrobes Online Maxi Wall Hung Series
Summary of Contents for Wardrobes Online Maxi Wall Hung Series
- Page 1 INSTALLATION INSTRUCTIONS MAXI WALL HUNG SERIES 1. Determine the back bar’s height. Standard wardrobes usually work best at a finished height of 2m from the floor (finished height is the height from the top side of the top shelf to the floor). The back bar needs to be installed 150mm lower than your desired finished height.
- Page 2 4. Line up the Suspension Bracket with the two sleeves, hook facing the back of panel where rebate is. Screw to secure. 5. Turn panel over, and screw the other 2 screws into holes. These meet with the thread in the sleeves to securely fit the Suspension Bracket to the panel. 6.
- Page 3 8. Install the receiving Drawer Runners using the Euro Screws pictured here. Wheels should face the front of the tower, and be screwed at both the front and back of the runner. Refer to Diagram A for drawer runner positions. Refer to Drawer Assembly Instructions for drawer assembly.
- Page 4 12. Once all panels and shelves/drawers are secured, measure along the top of the system from wall-to-wall to get your overall width measurement for the top shelf. Cut the top shelf to size using an 8pt saw. We recommend using masking tape along your cut line before you cut, to reveal a nice clean cut. Screw the top shelf into each vertical gable at the front and back.
- Page 5 Diagram A...
- Page 6 15-S 12-S 15-S 15-S 19-S 24-S 24-S 24-S 26-D 27-S 32-S 40-S 49-S 15-S 15-S 15-S 15-S 24-S 24-S 24-S 24-S 30-D 32-S 32-S 36-D 42-D 40-S 40-S 48-D 49-S 49-S 49-S 15-S 15-S 15-S 24-S 24-S 24-S 30-D 32-S 36-D 32-S 40-S...
-
Page 7: Installation Instructions
INSTALLATION INSTRUCTIONS DRAWER ASSEMBLY Front Face Back Panel Side Panels Front Panel Baseboard Tools Screws Cam Pins Cam Locks... - Page 8 1. Insert cam locks into holes in both drawer sides. The opening in the cam lock must face outwards. 2. Screw cam pins into drawer back panel and drawer front panel. 3. Attach both side panels to the drawer front panel. Insert drawer base board.
- Page 9 5. Tighten cam locks on both front panel and back panel. 6. Line up the front drawer panel with the front face panel. Use pencilled lines for accuracy. The bottom of the drawer should be flush with the drawer front face. Screw to secure.
- Page 10 INSTALLATION INSTRUCTIONS HANGING RAILS 1. For Top Height Rail: Measure 300mm from the back of the tower/wardrobe panel. From that mark measure 50mm down and mark with a pencil. If you are measuring from underneath a top shelf 50mm bracket, measure down 40mm from the bottom of the shelf bracket (this allows 10mm for the bracket). Install wall plugs where required for a stronger install.