Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Olimpia TI 150
- Page 1 Heat Detector TI 150 Operating Manual 10/2018 de v1.0...
-
Page 2: Table Of Contents
Low battery charge ......... . . 12 tI 150... - Page 3 Guarantee ........... 23 tI 150...
-
Page 4: Intended Use
Intended Use The TI 150 heat detector, subsequently referred to simply as the heat detector, serves for the detection of high temperatures indoors and to issue a loud acoustic signal if detected. If triggered, the heat detector sends a radio signal which can be received by alarm sys- tems in the Protect and ProHome series or other heat detectors. -
Page 5: Safety Instructions
Attention! Risk of property damage through the use of inappropriate batteries! The use of inappropriate batteries can cause a loss of function of the heat detector. Only use batteries of the type described in Section Technical Data. tI 150 etector... - Page 6 Do not remain in the vicinity of the acoustic alarm for a longer period when it has been triggered. Attention! Risk of property damage through environmen- tal influences! Prevent exposure to environmental influ- ences such as exposure to smoke, dust, vibration, chemi- cals, moisture, heat and direct sunlight. tI 150 etector...
-
Page 7: Notes On Use
■ The heat detectors detect the temperatures caused by a fire, not the flames them- selves. ■ It should be possible to hear the heat detectors throughout the entire living area. ■ People under the influence of alcohol, medication or drugs may not be alerted/ woken by the alarm signal. tI 150 etector... -
Page 8: Operating Elements
Operating Elements Base Battery compartment Heat detector (housing) Signal LED Test button (connection, Mute mode and function test) tI 150 etector... -
Page 9: Installation Without An Alarm System
Press the Test button (5) on one of the other heat detectors three times in succession. An acoustic alert signal is issued and the heat detector is connected to the main device. (Option:) Repeat the connection process for all the heat detectors to be connected. tI 150 etector... -
Page 10: Installation With An Alarm System
Connect more heat detectors to the main device (refer to Connecting heat detectors without an alarm system on page 9). Complete a function test following registration! Press the Test button (5). The function of the alarm signal, signal LED and, if necessary, connected devices are tested. 10 H tI 150 etector... -
Page 11: Operating Modes
The acoustic alarm can be switched to Mute mode by pressing the Test button (5). When Mute mode is activated, the signal LED (4) flashes for approx. 10 minutes at intervals of 8 seconds (refer to Mute mode on page 13). tI 150 etector... -
Page 12: Collective Alarm
Press the Test button (5) to interrupt the acoustic signal for low battery charge for about 8 - 10 hours. The heat detector then switches to Normal mode and operates as usual. It is recommended to change the batteries immediately (refer to Changing the Batteries on page 20)! 12 H tI 150 etector... -
Page 13: Device Error
In the case it is extended, the device switches to Alarm mode. Test mode You should test the heat detector on a weekly basis by pressing the Test button (5). The heat detector issues a loud acoustic alarm to confirm its functionality. tI 150 etector... -
Page 14: In The Event Of An Alarm
If you have linked the heat detectors to each other without an alarm system, notification occurs accordingly without an alarm system. The secondary devices issuing the alarm are switched off automatically independent of the main device after 10 minutes. 14 H tI 150 etector... -
Page 15: What To Do If The Heat Detectors Raise An Alarm
What types of injuries have occurred? Wait for instructions. ■ Try and extinguish the initial fires using the appropriate extinguishing agents available, such as fire extinguishers and fire blankets. However, never put your- self and others at risk. tI 150 etector... - Page 16 If several heat detectors are being used, the alarm from the detector trigger- ing the alarm remains active. This serves to localise the heat detector triggering the alarm. Press the Test button (2) on the heat detector triggering the alarm. The alarm is completely deactivated. 16 H tI 150 etector...
-
Page 17: Installation
■ directly under the roof (min. distance of 30 cm to the roof of an attic), ■ in the vicinity of open hearths or fireplaces, ■ in rooms in which the temperature can rise above + 40 °C or drop below + 0 °C. tI 150 etector... - Page 18 50 cm and maximally 250 cm. ■ If the room to be monitored is very large, it may be advantageous to install more than one heat detector. 50 cm-250 cm 50 cm-250 cm 18 H tI 150 etector...
- Page 19 You can only install the heat detector on the base (1) when a battery has been inserted in the battery compartment on the rear of the heat detector. Disassembly of the heat detector is performed in the reverse sequence. tI 150 etector...
-
Page 20: Changing The Battery
Install the heat detector in the base (1). When the heat detector is connected to an alarm system, the alarm system base unit also signals low battery power in the display. On completing the work, initiate a function test. 20 H tI 150 etector... -
Page 21: Technical Data
Alarm volume >85 dB(A) Batteries 2 x AA, 1.5 V (Gold Peak GP15A, Energizer E91, Raymax LR6) Area of application For bathrooms and kitchens Standard EN 14604:2005+AC:2008 Ambient conditions 0 °C to 40 °C at 30% to 75% rel. humidity tI 150 etector... -
Page 22: Information On Conformity
Clean the smoke inlet with a brush. Clean dust and cobwebs as necessary. Complete a function test each time after assembly, a change of batteries and a longer period of absence (Test mode on page 13). 22 H tI 150 etector... -
Page 23: Guarantee
Directive 2014/53/EU. The CE mark on the heat detector confirms its conformity. You can find further information on the Declaration of Conformity for this product at http://productip.com/?f=83845 or by scanning this QR code. tI 150 etector... - Page 24 Heat Detector TI 150 v1.0, 10.2018 Art. Nr. / Art. No. 6120 Subject to change without prior notice.
Need help?
Do you have a question about the TI 150 and is the answer not in the manual?
Questions and answers