1. Manuals
  2. Brands
  3. RTX Manuals
  4. Accessories
  5. RTX4069
  6. Instruction manual

RTX RTX4069 Instruction Manual

Wireless ip dect/wlan
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
w i r E l E s s i P D E C T / w l A n
B A s E s TAT i o n
( M o D E l : r T X 4 0 6 9 )
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RTX4069 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for RTX RTX4069

Summary of Contents for RTX RTX4069

  • Page 1 w i r E l E s s i P D E C T / w l A n B A s E s TAT i o n ( M o D E l : r T X 4 0 6 9 )

  • Page 2: Dear Customer

    This publication explains the steps for initial setup and configuration of the Base Station. It also provides troubleshooting information and detailed specifications. Copyright © 2007 RTX Network Systems. All rights reserved. All forms of copying or reproduction of the prod- uct are strictly prohibited.

  • Page 3: Table Of Contents

    TA B l E o f C o n T E n T s dear customer ............safety/ Warnings .

  • Page 4: Safety/ Warnings

    If the external antenna option is chosen an External antenna kit is required, RTX item no. 95101873 Using DECT repeaters extends the range of each Base Station and enables access to areas shielded from the Base...

  • Page 5: Initial Setup

    Housing • Cable gland note: If any item is damaged or missing, please notify RTX at WLLsupport@rtx.dk fig. 1: Note: If other cable glands than the ones supplied with the Ethernet Sync-Switch Unit are used then these must be non-inflammable type of either: •...
  • Page 6 2) Pull forward the upper section. fig. 3: fig. 4: 3) Unclip the lower section of the pivoted frontpiece. fig. 5: 4) Raise the lid. It will click, and is locked open at 90°.

  • Page 7: Connecting The Base Station To

    connecting the Base station to: The Base Stations may be connected to either a (1) Sync Unit or a (2) Ethernet Sync/Switch Unit (1) sync unit fig. 6: Connect at the 4-pin VDSL port (J400). 1) Punch out the plastic from a suitable hole in the housing. fig.
  • Page 8 fig. 9: 4) Strip off about 5cm of the cable sheath and cut the wire to length. 5) Insert through the gland seal and align the wires according to the diagram below and insert them in the 4-pin VDSL male connector (J400).

  • Page 9: Ethernet Sync/Switch Unit

    (2) ethernet sync/switch unit Connect to a Ethernet Sync/Switch Unit using a 100Base-T straight through Ethernet cable – type CAT.5 – (both ends are the same). fig. 12: 1) Punch out the plastic from a suitable hole in the housing. fig.
  • Page 10 fig. 15: 4) Strip off about 5cm of the cable sheath and cut the wires to length. fig. 16: 5) Insert through the gland seal and align the wires as in fig. 16 and table 1 and insert into RJ-45 connector. taBle 1 –...

  • Page 11: Wlan Card (Optional)

    Ethernet port is finished Wlan card (optional) for wireless lan functionality from the Base Station, an RTX-specified WLAN card is an option. To use a WLAN card: 1) With the power disconnected, push the WLAN card into the slot at an angle of about 25° (step 1 in fig. 18) and then press the WLAN card down until it locks into place (step 2 in fig.

  • Page 12: Led And Dip Switch Functionality

    led and dip sWitch functionality When the Base Station is powered on for the first time or if it has been reset to all default parameters, the LEDs display in the following sequence: vdsl connection For a VDSL connection, when there is power to the Base Station, the green LED 1 [ON] will be lit immediately and continuously.

  • Page 13: Status Leds

    status leds led numBer function colour activity teXt on pcB in fig. 29 - No light means no power Green - Light means power on - No light means Base Station not started initialising - Flashing means Base Station initialising ON-AIR Green ON-AIR...
  • Page 14 fig. 29: ON-AIR ERROR LINK dip switch functionality function function teXt off teXt on – top Antenna Switch between internal Switch off (default): control and external antenna internal antenna Switch on: external antenna Switch off (default): Antenna Switch between dipole control and patch antenna dipole antenna...
  • Page 15 fig. 30: (Shown in default setting: using dipole and internal antenna.)

  • Page 16: Placement And Lightning Protection

    (GPS position) and the MAC address of the Base Station. This information will be very useful for Base Station MKII BR later optimization and scaling of the network. Model no.: RTX 4069 1541 -08-4668 S/N: MAC: MADE IN...
  • Page 17 When the Base Station is used outdoors in conjunction with a Sync Unit, primary lightning protection is required. This should be placed at the point in the junction box where the multi-pair cable is divided for each individual Base Station. The Base Station should be at least 2 metres below the top of the elevated object to which it is attached.

  • Page 18: Technical/Physical Characteristics

    T E C h n i C A l / P h y s i C A l C h A r A C T E r i s T i C s compliant with • EN 300 019 Class 4.1E •...

  • Page 19: Anatel Homologation

    This phone is designed for use within a RTX Wireless IP Network. Any other use is deemed as not intended use. The company does not accept claims resulting from unauthorized alterations or modifications not described in this User Manual.

Table of Contents