1. Manuals
  2. Brands
  3. Hubbel Manuals
  4. Industrial Equipment
  5. Chance PSC2080547
  6. Intended use

Hubbel Chance PSC2080547 Intended Use

Swingarm
Hide thumbs

Advertisement

Table of Contents

PSC2080547 SWINGARM (END MOUNT)
PSC2080548 SWINGARM (SIDE MOUNT)
INSTRUCTIONS
Product Intended Use:
These instructions are intended to illustrate the installation and operation of the Hubbell
Power Systems, Inc. ("Hubbell") PSC2080547 and PSC2080548 swingarm into a suitable
Hubbell vault. This swingarm was designed to be compatible with the Commscope FDH
4000 closure and is independent from Commscope Inc.
PSC2080547 (END MOUNT)
shown in PG3060 Hubbell vault
Single Mount / Dual Mount
PSC2080548 (SIDE MOUNT)
Dual Mount shown in
PG3660 Hubbell vault
(No Torsion Assist Cover shown)
PSC2080547 & PSC2080548 Swingarm

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Chance PSC2080547 and is the answer not in the manual?

Questions and answers

Related Manuals for Hubbel Chance PSC2080547

Summary of Contents for Hubbel Chance PSC2080547

  • Page 1 PSC2080547 SWINGARM (END MOUNT) PSC2080548 SWINGARM (SIDE MOUNT) INSTRUCTIONS Product Intended Use: These instructions are intended to illustrate the installation and operation of the Hubbell Power Systems, Inc. (“Hubbell”) PSC2080547 and PSC2080548 swingarm into a suitable Hubbell vault. This swingarm was designed to be compatible with the Commscope FDH 4000 closure and is independent from Commscope Inc.
  • Page 2 TABLE OF CONTENTS PAGE NO. Introduction Table of Contents Guide To Warnings Product Information & Pre-Installation Instructions Product Installation & Use Instructions 5 - 10 TD06118E_0519...
  • Page 3 GUIDE TO WARNINGS WITHIN MANUAL The following is a list of warnings used within this manual and should be read in their entirety to ensure safe practices. WARNING CAUTION A WARNING refers to operating procedures, techniques, A CAUTION refers to operating procedures, techniques, etc., that, if not followed carefully, could RESULT IN etc., that, if not followed carefully, could RESULT IN DAMAGE TO EQUIPMENT or LOSS OF SERVICE to...

  • Page 4: Product Information

    PRODUCT INFORMATION Backing Plate 2a. Mounting Bracket PSC2080547 (end mount) 2b. Mounting Bracket PSC2080548 (side mount) Inner Tube 4. Outer Tube Stainless Steel Strap PRE-INSTALLATION INSTRUCTIONS When installing the swingarm in a Hubbell vault that is operational in the field, remove the dirt from the outside of the vault in the desired swingarm mounting location.
  • Page 5 PRODUCT INSTALLATION AND USE INSTRUCTIONS Disassemble the mounting bracket from the inner tube assembly as shown below in FIGURE 1 (optional) Inner Tube Mounting Bracket (shown - PSC2080547 End Mount) FIGURE 1 PSC2080547 (END MOUNT): For single swingarm: Mark the centerline of the top mounting holes 6.5” from the lid lip as shown in FIGURE 2.
  • Page 6 PSC2080548 (SIDE MOUNT) For single swingarm: Mark the centerline of the top mounting holes 4.0” from the lid lip and 11.0” from the inside end wall as shown in FIGURE 4. NOTE: Ensure placement of mounting bracket allows vault lid to close and avoids structural ribs of vault.

  • Page 7: Backing Plate

    Use the provided mounting hardware (3/8” carriage bolts, round washers, lock washers, and hex nuts) to install the mounting bracket as shown in FIGURE 7 or 8 Polymer concrete enclosure with NO torsion assist cover i. Place the backing plate flush on the outside of the vault ii.
  • Page 8 Install tube assembly if removed in Step 1. Install stainless steel strap by centering over the top strap bracket on the outer tube with the provided 1/4” bolt and lock nut (see FIGURE 9) Outer Tube Stainless Steel Strap FIGURE 9 Install FDH 4000 splice closure (purchased separately) with provided hardware (3/8”...

  • Page 9: Retracted Position

    10. Install hose clamp over the bottom strap bracket as shown in FIGURE 11 and secure FIGURE 11 11. Extend/Retract swingarm by gripping swingarm handle and pulling spring pin. Fully retracted and extended positions are shown below in FIGURES 12 & 13. NOTE: Swingarm was designed to have optional hard stops at 8”...
  • Page 10 12. Lower swingarm into the vault by grasping handle and lifting swingarm latch CAUTION When lower equipment into vault, ensure handle on outer tube is firmly held while actuating the swingarm latch to prevent damage to cables, closure, and/or vault. SEE FIGURE 14 Swingarm Latch FIGURE 14 (shown - PSC2080547 End Mount)

This manual is also suitable for:

Chance psc2080548

Table of Contents