Advertisement
Quick Links
I N S T A L L A T I O N I N S T R U C T I O N S
The PD10-M-CVR is a storefront grade 1 exit device equipped with motor drive latch retraction. Retrofits
C.
B.
A.
D.
PD10-M - C VR I nc l ud e s
A.
Head Cover pack
B.
CVR Exit Device
C.
Concealed Vertical Rods
D.
Hinge Stile End Cap pack
E.
Strike pack
F.
Retractor & Pinion pack
G.
Traveler pack
H.
MM4 - Installed in exit device
I.
6' Power Lead
U.S. Customer Support
1-888-622-2377
PD10-M-CVR
Doromatic 1690 & First Choice 3690.
E.
F.*
*Certain parts may already be attached to rods
Visit our website for more details
www.CommandAccess.com
G.*
Tool s R eq u ired
•
Cordless Drill
•
Needlenose Pliers
•
Measuring Tape
•
1/2 Drill bit
Canada Customer Support
1-855-823-3002
I.
H.
1
Doc # 20201_C
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Command access PD10-M-CVR
- Page 1 I N S T A L L A T I O N I N S T R U C T I O N S The PD10-M-CVR is a storefront grade 1 exit device equipped with motor drive latch retraction. Retrofits Doromatic 1690 &...
-
Page 2: Specifications
T E C H N I C A L I N F O R M A T I O N Specifications • Input Voltage: 24VDC +/- 10% • Average Latch Retraction Current: 1 Amp • Average Holding Current: 125 mA PTS Video •... -
Page 3: Installation Example
NO VOLTAGE LOCKING HARDWARE Module Legend Standard Placement Optional Placement RECOMMEND POWER SUPPLIES: All Command Access exit devices & field installable kits have been thoroughly cycle tested with Command Access power supplies at our factory. • PS210 • PS440B • •... - Page 4 Concealed Vertical Rod For Bottom Rod Latch Installation Template All prep is shown on interior side of the door, except where noted. Right hand door shown. (LHR)
- Page 5 STEP 1 - Install Vertical Rods (Rods are factory preset for door height of 83 3/16 and a cylinder location of 41 5/16- see page 9 for additional details.) Install top latch mechanism using 2 ea. #10-31X1/4 screws. Pic 3 Affix bent end of rod on door using rod bushing with “E”...
- Page 6 Slide the end of baserail underneath the mounting bracket. Attach head of device to stile with 2 ea. 1/4-20x1/2 flat head screws. Tighten screws on the head and tail of the device. STEP 3 - Drill Wire Chase Remove lock stile end cap.
- Page 7 Slide push pad off of baserail. Drill the hole for our 2 pin power lead in- between the 2 mounting screws. Debris Feed the 2 pin power lead into the hole and connect to our MM4 module. Also, make sure to clean out any debris left. Note: Depending on where your power transfer is;...
- Page 8 Replace push pad, making sure the activating brackets and pins slide through the 3 channel. Reinstall the lock stile end cap. STEP 4 - Attach Vertical Rods Before installing the traveller. Remove Axle screw, allowing the lifting arm to relax and move out of the way.
- Page 9 Install Traveller onto the bent end of the vertical rods. Re-install Axle screw and tighten. Install Pinion support bracket and tighten retainer screw.
- Page 10 Optional STEP - Installing Cylinder Flat Side Place Pinion with black cylinder bushing into the door with the cylinder tail piece sliding into the back of the pinion. Flat side of pinion facing up. Add Retractor and Traveller lift bracket. Pick placement of pinion depending on desired function.
- Page 11 Install Pinion support bracket and tighten retainer screw. STEP 4 - Continued -Check Top Rod operation. When push pad is depress fully, top latch should open and allow top strike to pass, and swing freely. -Check Bottom Rod operation. The bottom latch should not protrude more than 1/16 inch below the bottom of the door when the push pad is depressed.
- Page 12 Install hinge stile push pad cover with 2 ea. 8-32 x 1 1/2” screws. Now you set you latch retraction adjustment with our “PTS” technology. See page #2 Optional STEP - How to change handing Remove the Axle screw and lifting arm. Lifting arm.
- Page 13 PD10 Parts Breakdown...
- Page 14 Visit our website for more details U.S. Customer Support Canada Customer Support 1-888-622-2377 1-855-823-3002 www.CommandAccess.com...
Need help?
Do you have a question about the PD10-M-CVR and is the answer not in the manual?
Questions and answers