Register your product and get support at
ENG
Quick Start Guide
N.V.
Electronics
Philips
CED320
1
a
b
c
e
English
reserved.
rights
All
Connector Connect to
Koninklijke
2008
©
1
Black wire A metal surface of the car
Overview of parts
These are the supplierd parts needed to connect
and install this unit.
2
Yellow wire The +12V car battery which
a Carry case with front panel stored inside
3
b Trim plate
Orange/
white wire
c Standard connector
4
Red wire
d Rubber cushion
e Removal keys x 2 pcs
f Screw x 4 pcs
Connect wires: ISO connectors
1
Pull out the ISO connectors from the car
5
Green and
dashboard and connect them to the bigger
green/black
end of the supplied standard connector.
wires
2
6
Connect the other end of supplied standard
White and
connector to the unit.
white/black
wires
3
Do the other connections, if applicable.
7
Gray and
gray/black
wires
Connect wires: without ISO
8
Purple and
connectors
purple/
black wires
1
Cut off the bigger end of the supplied stan-
dard connector.
3
Connect the supplied standard connector to
2
Check the car's wiring carefully, then connect
the unit.
them to the standard connector.
4
Do the other connections, if applicable.
2a
2b
d
f
Connect parking brake cable
First connect the black ground
(earth) lead, then connect the
Connect reverse driving cable
yellow and red power supply
leads.
is live at all times .
Attach the front panel
Illumination switch
1
Attach the trim plate.
The +12V power terminal
2
Insert the left side of the panel in the chassis
which is live in the accessory
until it is correctly engaged.
(ACC) position of the ignition
3
switch
Press the right side of the panel until the
mechanism locks it into place.
If there is no accessory posi-
4
tion, connect to the +12V car
Close the front panel.
battery terminal that is always
live. Be sure to connect the
Mount in the dashboard
black ground (earth) lead to a
metal surface of the car fi rst.
Note
Left speaker (Rear)
•
For proper operation of the DVD player, the
chassis must be mounted within 20 degree
Left speaker (Front)
horizontal. Ensure that the unit is mounted
within this limitation.
•
Check wire connection before you mount
the unit into a car.
Right speaker (Front)
If preset radio stations are lost when the
•
ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to
Right speaker (Rear)
the yellow ones.
1
If the car does not have an on-board drive or
navigation computer, disconnect the negative
terminal of the car attery.
•
If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer may
lost its memory.
•
If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
2
Ensure that car dashboard opening is within
these measurements:
3
Remove the two transport screws on the
top of the unit.
8
1
2
7
3
4
6
5
4
Set clock
Remove the mounting sleeve with the
removal keys.
1
Press MENU .
5
Install the sleeve into the dashboard and
2
Press the navigation buttons to select [SET-
bend the tabs outward to fi x the sleeve.
TINGS] , then press SEL on the remote
•
If the unit is not fi xed by sleeve but by
control.
the supplied screws, skip this step.
3
6
Select [SYSTEM] , then press
Place the rubber cushion over the end of the
4
bolt.
Select [TIME MODE] , then press
7
The time mode options are displayed:
»
Slide the unit into the dashboard until a click
sound is heard.
[12 HOUR MODE]
»
8
[24 HOUR MODE]
Reconnect the negative terminal of the car
»
battery.
5
Sselect a mode, then press SEL .
6
Press
to return to previous menu and
select [TIME ADJUST] , then press
Detach the front panel
7
Press
or
to enter clock, then press SEL .
The front panel can be detached and taken with
you to deter theft.
Tune to a radio station
Note
1
Press SOURCE to select Tuner.
2
•
Before installing the unit, detach the front
Press
or
to select band.
panel.
[FM] or [AM] is displayed.
»
3
Press
or
to tune to a radio station
1
Press
to release the panel.
manually.
2
•
To search for radio station automatically,
Open the panel, then push the right side
panel toward the left side to disengage it
press
or
from the chassis.
3
Take off the panel and store it in the supplied
carry case to protect it from dirt or damage.
Play discs
1
Press
to open the front panel.
2
Turn on
Insert the disc into the disc slot with label
side facing up.
1
Press the
knob to turn on the unit.
Play resumes from the point where it was
»
The unit plays the last listened program:
last stopped.
»
DVD, Tuner, USB or SD/MMC Card (if there is
3
To remove the disc, press the button.
USB device or SD/MMC card connected).
When the disc is ejected, the unit switches
»
•
To turn off the unit, press the
knob for
to TUNER mode automatically.
more than 2 seconds.
4
Close the front panel.
•
When the unit is idle for over 5 minutes, it
After a few seconds, the screen turns on.
goes to standby mode and displays screen
»
saver.
For video discs, if a menu appears: press
»
or
to select an item, then press
play.
ANTENNA
SUB OUT
PARKING
REAR LINE OUT R
REAR LINE OUT L
FRONT LINE OUT R
FRONT LINE OUT L
CAMERA IN
VIDEO OUT 2
VIDEO OUT 1
CAMERA
For discs that contain MP3s, WMAs, or
»
JPEGs: , press
or
to select a folder/track/
picture, then press
to start play.
Insert USB device
.
1
.
Slide down the USB socket cover.
2
Insert the USB device into the USB socket.
The unit star ts playing from the USB
»
device automatically.
Insert SD/MMC card
.
1
Press
to open the front panel.
2
Insert the SD or MMC card into the card
slot.
The unit starts playing from the SD/MMC
»
card automatically.
for 3 seconds.
to start