Summary of Contents for KLOPPENBERG 500-P
- Page 1 AUSTRALIA MANUAL DISPENSER MODEL 500-P 1000-P 1100-P TOLL FREE: 1-800-346-3246 303-761-1615 FAX: 303-789-1741 MONDAY – FRIDAY 8 a.m. – 5 p.m. KLOPPENBERG 2627 WEST OXFORD AVENUE ENGLEWOOD, CO 80110 www.kloppenberg.com...
- Page 2 KLOPPENBERG DISPENSER FEATURES • Increase profits by saving time on labor. • Helps create a sanitary environment. • Built for the serious customer that wants results without the glamour. • Foot pedal activation eases bagging and reduces the liability risks.
- Page 3 Model 500-P This dispenser is the original dispenser with a single chute. Model 1000-P This dispenser is double the capacity of the 500-P model and has a single chute and two agitators. Model 1100-P This dispenser is two 500-P dispensers put together with a cutout between the two and has two chutes and two foot pedals and will operate individually of each other.
-
Page 4: Start-Up Procedure
4. Plug dispenser cord into an adequately sized receptacle. B. Cleaning 1. Perform a start up cleaning procedure for the ice maker as indicated by ice maker manufacture’s operating manual. 2. Thoroughly clean and sanitize the dispenser per Kloppenberg’s attached Cleaning and Maintenance Instructions. Page 3... - Page 5 KLOPPENBERG DISPENSER 1000-P Page 3A...
-
Page 6: Operating Instructions
Keep the door closed while operating. The unit will not operate while the door is open. Clean regularly following Kloppenberg’s Cleaning and Maintenance instructions sent with each unit. Use the paddle provided to break up the ice only. Make sure to hang the paddle back up on the hook bracket provided to keep it clean. - Page 7 KLOPPENBERG DON’T DO THIS… Don’t put your hands, arms or any foreign objects into chute or hopper while unit is activated. Don’t leave any foreign objects inside the bin. Don’t let the ice sit for over 24 hours, ice may freeze up causing ice bridges.
- Page 8 KLOPPENBERG MOST COMMON REASONS WHY ICE WILL NOT DISPENSE Is the door closed? The door must be closed or unit will not operate. Is the motor running? If motor is not running, the overload switch on the motor probably has tripped.
- Page 9 KLOPPENBERG PRVENTIVE MAINENANCE ELECTRICAL WARNING ***DISCONNECT POWER BEFORE SERVICING*** Weekly cleaning is recommended. Empty dispenser of all ice. Thoroughly clean and sanitize by following the attached Cleaning and Maintenance Instructions. Clean and flush drains. Lubricate every 6 months. Use a Phillip’s screwdriver to remove the rear chain cover.
- Page 10 KLOPPENBERG PRIOR TO ANY SERVICE OR REPAIR – DICONNECT POWER CORD BY UNPLUGGING IT FROM THE RECEPTICAL AGITATOR REPLACEMENT PROCEDURE Removing a damaged agitator is accomplished through the upper access door. Open the door and raise the lexan baffle up to the locked position.
-
Page 11: Electrical Schematic
KLOPPENBERG ELECTRICAL SCHEMATIC 220 VOLTS TO 24 VOLTS TRANSFORMER 2 AMP FUSE POWER RELAY Page 9... - Page 12 KLOPPENBERG DISPENSER SECTION VIEW Page 10...
- Page 13 KLOPPENBERG DISPENSER SECTION VIEW REFERANCE KEY LOCATION DESCRIPTION AGITATOR FRONT ASSEMBLY AGITATOR AGITATOR REAR ASSEMBLY AUGER FRONT ASSEMBLY AUGER AUGER REAR ASSEMBLY CHAIN COVER COPPER DRAIN MOTOR/REDUCER ASSEMBLY POWER CORD SUPPORT FRAME ASSEMBLY ELECTRICAL BOX ASSEMBLY FOOT PEDAL SWITCH BAG/CONTAINER SHELF...
- Page 14 KLOPPENBERG DISPENSER PARTS LIST PART# DESCRIPTION PART# DESCRIPTION AGITATOR FRONT ASSEMBLY 4080021 COPPER DRAIN ASSEMBLY 4080023 AGITATOR FRONT BRACKET MOTOR ASSEMBLY 2700042 AGITATOR BUSHING UHMWP ½ HP 220 VOLTS MOTOR 2300044 SHAFT COLLAR 2400088 GEAR REDUCER 4080005 AGITATOR MOTOR MOUNTING BRACKET...
- Page 15 KLOPPENBERG SHIPPING ASSEMBLY INSTRUCTIONS Insert auger into liner opening, placing drive end onto drive shaft and turn auger till it is locked on drive shaft pins. Place shaft collar on auger shaft end leaving it loose. Next put auger bracket onto auger shaft and mount to front of bin using ¼-20 hex-head screws with lock washer.
- Page 16 KLOPPENBERG Manufacturer Warranty Kloppenberg warrants to the original purchaser that it will repair or replace at its own cost any all- stainless commercial ice dispensing unit of its manufacture bearing the name Kloppenberg due to factory defect in material and/or workmanship occurring within the first year from the date of sale. All Kloppenberg products must be installed, adjusted and maintained in accordance with the procedures set forth in the Maintenance Instructions and General Conditions provided with each unit to qualify for subject warranty.