Page 1
AvoKey Installation with 1221-2041 and 1221-2045 AvoKey Hardware installation guide for Upgraded Tiger Touch consoles using the Fujitsu D3243 MB upgrade (F-V10 upgrade) i.e. Consoles requiring an extra USB cable and Avolites Kit number 8000-6103 Version 1.0 This document, the product and procedures it describes within are intellectual property of...
Page 2
Avolites has a policy of continuous product and documentation improvement. As such the detail within this manual may not match the operation of the Console/Server. In no event shall Avolites be liable for any direct, indirect, special, incidental, or consequential damages or loss whatsoever (including, without limitation, damages for loss of profits, business interruption, or other pecuniary loss) arising out of the use or inability to use Tiger Touch even if Avolites Ltd.
............5 CONNECTED TO THE 2.2 U-UPS MB ............... 6 CONNECTED TO THE 2.3 TT-P ................7 RO CONTINUED 3. RELICENSING .................. 12 4. LETTING US KNOW ................12 D:\Data\products\AVOKEY\release\8000-6103 TTPro-FV10-AVOKEY upgrade with 1221-2041 and 1221-2045.docx GK 11 October 2019...
In this case contact Avolites direct to establish which kit you may need. After the installation of the Avokey you can use the console as normal with software versions before V12. In order to use V12 you will need to download it and install as per normal, this is then followed by the “authentication”...
C. Re-fit the cable retention comb and secure with the retained fixings (M3x12 screw, spring washer & flat washer). Push the comb in the direction of the arrows before tighten the screws D:\Data\products\AVOKEY\release\8000-6103 TTPro-FV10-AVOKEY upgrade with 1221-2041 and 1221-2045.docx GK 11 October 2019...
Page 6 of 12 Continue to 2.3 TT Pro continued U-UPS connected to the MB Cut the three cable-ties as shown below Disconnect UPS USB cable from motherboard port D:\Data\products\AVOKEY\release\8000-6103 TTPro-FV10-AVOKEY upgrade with 1221-2041 and 1221-2045.docx GK 11 October 2019...
C. Re-fix the PWM Loom (grey ) to the safety frame with cable ties TT-Pro continued D. Unplug the UPS USB cable from U-UPS board (or DC-UPS-C board) and discard the cable D:\Data\products\AVOKEY\release\8000-6103 TTPro-FV10-AVOKEY upgrade with 1221-2041 and 1221-2045.docx GK 11 October 2019...
Page 8
H. Locate the other side of this cable on the U-HUB board and disconnect I. Cut the cable-ties (arrows) then remove the UPS USB cable and discard the cable D:\Data\products\AVOKEY\release\8000-6103 TTPro-FV10-AVOKEY upgrade with 1221-2041 and 1221-2045.docx GK 11 October 2019...
Page 9
K. Connect supplied 10Way USB to Type B and U-HUB feed cable (2x5 connector side to located the 2xUSB2 port on motherboard with the Red wires up Red wires D:\Data\products\AVOKEY\release\8000-6103 TTPro-FV10-AVOKEY upgrade with 1221-2041 and 1221-2045.docx GK 11 October 2019...
Page 10
N. Connect 10way USB to Type B and U-HUB feed cable (USB-B type end) to U-UPS board (or DC-UPS-C board) O. Place the cable excess of the UPS connection under the U-UPS board (arrow) D:\Data\products\AVOKEY\release\8000-6103 TTPro-FV10-AVOKEY upgrade with 1221-2041 and 1221-2045.docx GK 11 October 2019...
Page 11
R. Locate Blue colour USB3.0 port on motherboard (near the ATX connector) S. Plug the AvoKey stick into the located USB3.0 port T. Close the console with previously removed M4 screws D:\Data\products\AVOKEY\release\8000-6103 TTPro-FV10-AVOKEY upgrade with 1221-2041 and 1221-2045.docx...
TitanLicensing@avolites.com, or call +44 208 965 8522 between 9am and 5pm UK Time and we will endeavour to ensure you receive your licence in the shortest possible time.
Need help?
Do you have a question about the AvoKey and is the answer not in the manual?
Questions and answers