Page 4
Important Information Warranty The VXI-1500 mainframe is warranted against defects in materials and workmanship for a period of one year from the date of shipment, as evidenced by receipts or other documentation. National Instruments will, at its option, repair or replace equipment that proves to be defective during the warranty period.
Page 5
Notices to User: Changes or modifications not expressly approved by National Instruments could void the user’s authority to operate the equipment under the FCC Rules.
Page 6
This equipment contains voltage hazardous to human life and safety, and is capable of inflicting personal injury. • Mainframe GroundingThe VXI-1500 mainframe requires a connection from the premise wire safety ground to the mainframe chassis earth stud. The earth safety ground must be connected during use of this equipment to minimize shock hazards.
Page 8
Preparation ........................3-1 Cleaning ........................3-2 Interior Cleaning ..................... 3-2 Exterior Cleaning .................... 3-2 Cleaning the Fan Filters....................3-3 Resetting the AC Mains Circuit Breaker ............... 3-4 Troubleshooting the VXI-1500 ..................3-4 Appendix A Specifications Electrical........................A-1 Cooling .......................... A-3 Safety..........................A-5 Environmental .......................
Page 9
Table of Contents Figures Figure 1-1. Rack-Mount Slide Kit ................1-3 Figure 1-2. Front View of the VXI-1500 Mainframe ..........1-5 Figure 1-3. Rear View of the VXI-1500 Mainframe ........... 1-6 Figure 2-1. VXI-1500 Mainframe Airflow Side View ..........2-2 Figure 2-2.
Page 10
This manual is organized as follows: • Chapter 1, Getting Started, describes the key features of the VXI-1500, lists the contents of your kit, and lists optional equipment you can order from National Instruments. • Chapter 2, Installation and Configuration, describes the necessary procedures for correctly preparing and operating your VXI-1500 mainframe.
Page 11
Module/Mainframe to Receiver Interconnection Customer Communication National Instruments wants to receive your comments on our products and manuals. We are interested in the applications you develop with our products, and we want to help if you have problems with them. To make it easy for you to contact us, this manual contains comment and configuration forms for you to complete.
Chapter Getting Started This chapter describes the key features of the VXI-1500, lists the contents of your kit, and lists optional equipment you can order from National Instruments. Unpacking Caution: Removal of the mainframe from the shipping carton requires two people.
Optional Equipment An optional rack-mount slide kit is available from National Instruments. As shown in Figure 1-1, this kit allows you to easily slide the VXI-1500 mainframe into and out of a standard 19 in. (482 mm) instrument cabinet. The slide kit is suited for instrument racks from 24 in. (600 mm) to 32 in.
Mounting Brackets Adjustable Slides Figure 1-1. Rack-Mount Slide Kit The VXI-1500 has been designed to work with standard interlocking receiver devices defined by the VXIplug&play Systems Alliance VPP-8 specification. Refer to the Receiver Interconnect Devices section of Chapter 2, Installation and Configuration, for information about preparing your mainframe for receiver installation.
The mainframe’s modular design ensures the highest level of maintainability resulting in a very low mean time to repair (MTTR). The VXI-1500 fully complies with the VXIbus Specification Revision 1.4 and is VXIplug&play-compatible.
Chapter 1 Getting Started Figures 1-2 and 1-3 show some of these key features and components of the VXI-1500 mainframe. Figure 1-2 shows the front view of the VXI-1500 mainframe and Figure 1-3 shows the rear view. Removable Rubber Feet...
Figures 2-1 and 2-2. Place your VXI-1500 on a bench top or in an instrument rack in such a way as to allow adequate ventilation near the fan tray (air inlets) and near the air outlet apertures along both sides of the mainframe.
Installation and Configuration Installing or Removing the Mainframe Front Door The VXI-1500 comes standard with a removable front door, as shown in Figure 2-3. To remove the door, rotate both locking knobs counterclockwise, partially open the door, and lift straight up. To re-install the door, line up the hinges of the door with those on the mainframe and lower the door into position.
Setting Fan Speed The fan speed selector switch is located on the rear panel of the VXI-1500. Refer to Figure 1-3 for a diagram of the fan speed selector. Select HI for maximum cooling effectiveness or LO for more quiet operation.
Routing Cables The VXI-1500 has a built-in cable channel providing a variety of options for instrument cable routing. The channel is located in the bottom section of the mainframe. Cables may be routed out the front by removing the cable access panel via the four thumbscrews.
Chapter 2 Installation and Configuration Remote Power Monitoring and Inhibit Interface The VXI-1500 mainframe provides for remote power monitoring and inhibit via a 25-position female D-sub connector located on the rear panel. Table 2-2 shows the pinout of the DB-25 connector.
For remote reset, connect a momentary switch between pin 24 and pin 11 of the DB-25 connector. Receiver Interconnect Devices Your VXI-1500 mainframe has been designed to meet the VXIplug&play Systems Alliance VPP-8 specification, VXI Module/Mainframe to Receiver Interconnection. The specification defines the required mounting structure to ensure that any VXIplug&play-compatible...
Chapter Maintenance This chapter describes basic maintenance procedures you can perform on the VXI-1500 mainframe. Service Interval Clean the mainframe fan filter at a maximum interval of six months. Depending upon the amount of use and ambient dust levels in the operating environment, the filters may require more frequent cleaning.
Figure 3-1. Thumbscrews Fan Filter Figure 3-1. VXI-1500 Thumbscrews Clean the fan filter by washing in a mild soap solution, and then vacuuming or blowing air through the filter. Rinse the filter with water and allow to dry before replacing it in the mainframe.
VXIbus modules for troubleshooting your modules. Troubleshooting the VXI-1500 Refer to Table 3-1 to troubleshoot the VXI-1500 mainframe. The table lists possible causes why the power does not come on and gives recommendations for correcting the problem.
Maintenance Table 3-1. Troubleshooting Possible Cause What to Do VXI-1500 mainframe not Make sure that the VXI-1500 is connected connected to power source. to a live electrical outlet. Try operating another piece of equipment from this outlet. Power switch is not Set the front power switch to the On (1) switched on.
Appendix Specifications This appendix contains complete specifications for the VXI-1500 mainframe. Electrical Table A-1. AC Input Specifications Characteristic Description Input Voltage Range 85 to 264 VAC Input Frequency Range 47 to 500 Hz Over-Current Protection 15 A circuit breaker Inrush Current...
This appendix describes the P1 and P2 connector pinouts for the VXI-1500 backplane. Table B-1 shows the P1 connector pinouts for all slots in the VXI-1500. Table B-2 shows the P2 connector pinouts for all non-Slot 0 slots. Table B-3 shows the P2 connector pinouts for the VXIbus Slot 0.
Page 43
Electronic Services Bulletin Board Support National Instruments has BBS and FTP sites dedicated for 24-hour support with a collection of files and documents to answer most common customer questions. From these sites, you can also download the latest instrument drivers, updates, and example programs. For recorded instructions on how to use the bulletin board and FTP services and for BBS automated information, call (512) 795-6990.
Page 44
Telephone and Fax Support National Instruments has branch offices all over the world. Use the list below to find the technical support number for your country. If there is no National Instruments office in your country, contact the source from which you purchased your software to obtain support.
Page 45
National Instruments for technical support helps our applications engineers answer your questions more efficiently. If you are using any National Instruments hardware or software products related to this problem, include the configuration forms from their user manuals. Include additional pages if necessary.
Page 46
Complete a new copy of this form each time you revise your software or hardware configuration, and use this form as a reference for your current configuration. Completing this form accurately before contacting National Instruments for technical support helps our applications engineers answer your questions more efficiently.
Page 47
Other Products List and describe all devices installed in your mainframe. Indicate if any are receiver interconnect devices. Slot Logical Interrupt Manufacturer, Description, and Function Address Level...
Page 48
Documentation Comment Form National Instruments encourages you to comment on the documentation supplied with our products. This information helps us provide quality products to meet your needs. Title: VXI-1500 User Manual Edition Date: March 1997 Part Number: 321510A-01 Please comment on the completeness, clarity, and organization of the manual.
Page 54
Index side view (figure), 2-2 customer communication, xii, C-1 to C-2 maintenance of VXI-1500, 3-1 to 3-5 cleaning, 3-2 exterior, 3-2 interior, 3-2 DB-25 connector pinout (figure), 2-8 precautions, 3-2 documentation fan filters, cleaning, 3-3 conventions used in manual, xii...
Page 55
C-1 to C-2 2-5 to 2-6 telephone and fax support, C-2 electrical specifications, A-1 to A-3 troubleshooting the VXI-1500, 3-4 to 3-5 AC input, A-1 to A-2 DC output, A-2 to A-3 troubleshooting (table), 3-4 to 3-5 voltages at power monitoring (table), 2-6...