Table of Contents
Advertisement
Quick Links
INSTALLATION & OPERATING INSTRUCTIONS
INSTALLATION ET UTILISATION
ISTRUZIONI PER L'INSTALLAZIONE E L'USO
Form No. 3102939.042 1/92
21991.1992 The Dometic Corp.
LaGrange. IN 46761 USA
A&E E Systems
DIRECT MOUNTING CASE AWNING
AUVENT ENCASTRE POUR MONTAGE DIRECT
TENDA AVVOLGIBILE PER IL MONTAGGIO DIRETTO
FOR MINI-MOTORHOMES, PICK-UP CAMPERS, VANS,
VAN CONVERSIONS & POP-UP TENT TRAILERS
POUR CAMPING CARS, PICK-UPS, FOURGONS,
CAMIONS-MAGASINS ET CARAVANES PLIANTES
PER CARAVAN, CAMPER PICK-UP, FURGONI,
FURGONI MODIFICATI E AUTOCARAVAN
AW250
AW300
AW350
AW400
Advertisement
Table of Contents
Related Manuals for A&E Systems Electrolux AW Series
Summary of Contents for A&E Systems Electrolux AW Series
- Page 1 A&E E Systems DIRECT MOUNTING CASE AWNING AUVENT ENCASTRE POUR MONTAGE DIRECT TENDA AVVOLGIBILE PER IL MONTAGGIO DIRETTO FOR MINI-MOTORHOMES, PICK-UP CAMPERS, VANS, VAN CONVERSIONS & POP-UP TENT TRAILERS POUR CAMPING CARS, PICK-UPS, FOURGONS, CAMIONS-MAGASINS ET CARAVANES PLIANTES PER CARAVAN, CAMPER PICK-UP, FURGONI, FURGONI MODIFICATI E AUTOCARAVAN AW250 INSTALLATION &...
- Page 2 ELECTROLUX AW ELECTROLUX AW AWNING NOTE: Be sure to use a dab of Silicone Sealant on every INSTALLATION / OPERATION screw where a hole has been drilled in the side of the vehicle. This will prevent possible water leakage. Application: The Electrolux AW Case Awning is designed and intended for direct mounting on straight and most curved mini-motor- homes, pick-up campers, vans, van conversions and pop-up...
- Page 3 NOTE: Make sure Lock in top of awning Arm Assembly 7. Loosen Lock Knob and extend Arm Assembly keeping clears top of Case Lip. Fig. 4C. arm perpendicular to vehicle. Once location is deter- This is necessary for awning to open properly. mined, tighten Lock Knob.
- Page 4 AWNING BOTTOM MOUNTING BRACKET 15. While holding Pull-Strap firmly, release Lock Knobs on 10. Re-attach Foot to Bottom Mounting Bracket. Loosen Rafter Arms and allow awning to roll up. Fig. 15. Lock Knob on Arm Assembly. Raise Inner Arm as high Awning Case should close tightly.
-
Page 5: Operation Instructions
OPERATION INSTRUCTIONS D. Set awning into Pivot Position by inserting the awn- ing Foot into the Bottom Mounting Bracket Figs. 4A TO OPEN and 4B. BOTTOM BOTTOM . FOOT 1. Using Wand, open awning Case by inserting Pin on end of Wand into hole in Arm Assembly indicated by arrows on bottom of Case. - Page 6 into place to lock awning in full extension. Listen for “Click” TO CLOSE of Rafter Lock Buttons and continue to pull on Pull-Strap to make sure that Rafter Locks are fully set before releas- ing Pull-Strap. Tighten Lock Knobs. Fig. 5C. TO CLOSE ON STRAIGHT SIDEDVEHICLE PARTIAL EXTENSION 1.
- Page 7 5. Insert Pin at end of Wand through hole in Outer Arm so SIDE VIEW It aligns Foot for easy storage. Fig. 5A. Swing Arm up to Case. Fig. 5B. Slide Arm and Foot away from center ASSEMBLY _ of Case so foot can be inserted into center section of awning Case.
- Page 8 OPTIONAL ADAPTERS (BRACKET ASSEMBLIES) FOR AWNING INSTALLATION (Except for FIG. B Kit, all needed components are included in the parts package) FIG. A FIG. BRACKET ASSEMBLY FOR VAN INSTALLATION WITH OPTIONAL VAN STANDARD FLAT MOUNT INSTALLATION ADAPTER BRACKETS (Kit No. 930035) WITH AWNING RAILS (For permanent or temporary mounting onto rain gutters)