Advertisement
Quick Links
Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself
and others by observing all safety information. Failure to comply with instructions could result in personal injury
and/or property damage! Retain instructions for future reference.
Figure 1. 5600 Style Brake
Figure 2. Outline Drawing (does not include kit components)
Number of
Model
Torque
Rotating
Number
Discs
61003-560*
1
61006-560*
1
62010-560*
2
Table 1. Brake Specifications
* Last digit of model number
1 = With both manual release and external wire outlet
2 = With manual release and without external wire outlet
**Thermal capacity (HPS/MIN.) was determined under the following test conditions: a) Room temperature 72
c) Brake mounted in a horizontal position. d) Equal on and off times. e) 1800 RPM f) Coil energized with 110% of rated voltage.
DESCRIPTION
This brake is direct acting, electromagnetically released and spring set.
It uses rotating and stationary disc contact to supply positive braking action.
It retains quick release and setting capabilities at all times. Simplicity of design
has reduced maintenance to an absolute minimum. As with any electro-
mechanical equipment, however, periodic inspection and adjustment will assure
optimum performance. As the friction disc wears, the magnet gap will increase.
The magnet gap should be checked periodically and adjusted when necessary.
WARNING: Do not install or use these brakes in an
explosive atmosphere.
**Thermal
Motor
Housing
Capacity
lb-ft
Frame
Material
HPS/MIN
3
6
56C
Steel
10
www.dingsbrakes.com
Inertia of
Rotating
X
G
Parts Lb-ft
2
6
0.006
0.81 0.31 4.01 1.00 0.045/0.060
6
0.006
0.81 0.31 4.01 1.00 0.045/0.060
6
0.010
0.81 0.31 4.01 1.00 0.050/0.065
3 = Without manual release and with external wire outlet
4 = Without both manual release and external wire outlet
o
1
Bulletin No. BK4684 (1/11)
60 Series End Mount
Brake Instructions
NEMA 2 Enclosure
Dimensions
N +
Air Gap
C
1/32
Min.
F. b) Stopping time of one second or less.
Air Gap
Max.
0.220
0.220
0.220
Advertisement
Summary of Contents for Dynamics Dings 60 Series
- Page 1 Bulletin No. BK4684 (1/11) 60 Series End Mount Brake Instructions NEMA 2 Enclosure Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
- Page 2 WARNING Brake performance and features must be carefully matched to the requirements of the application. Consideration must be given to torque requirements, especially where an overhauling condition exists, as well as thermal capaci- ty, ambient temperature, atmospheric explosion hazards, type of enclosure and any other unusual conditions.
- Page 3 MAINTENANCE AND SERVICE (Continued) TROUBLESHOOTING (Continued) WEAR ADJUSTMENT (See Figure 4 & Table 1) BRAKE DOES NOT RELEASE As friction disc wears, the magnet air gap will increase. When “AIR Check for broken leadwire(s) or bad electrical connection(s). GAP” reaches 0.220” maximum, adjust to 0.045”- 0.060” for 1-disc Check for burned out coils (coils may be charred or burned).
- Page 4 Table 2. Parts List QUANTITY ITEM PART DESCRIPTION Model Number NUMBER 61003-560* 61006-560* 62010-560* Assembly, Bracket Plate with Studs K060637-004 Stud H060667-001 Bolt, Carriage, Pivot W001044-026 Washer, Spacer G061046-001 Lockwasher W004006-007 Nut, Hex W003002-002 Spring, Pressure Arm Return G061047-001 Washer, Flat W004013-017 Spring, Pivot G061048-001...
Need help?
Do you have a question about the Dings 60 Series and is the answer not in the manual?
Questions and answers