Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for ADLINK Technology ACLD-9185
- Page 1 ACLD-9185 16 Channel Relay Output Board...
- Page 2 Trademarks ACLD-9185 is registered trademarks of ADLink Technology Inc. IBM PC is a registered trademark of International Business Machines Corporation. Intel is a registered trademark of Intel Corporation. Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.
-
Page 3: Table Of Contents
How to Use This Guide..........ii 1. Introduction..............1 Features..................1 Applications ................2 Specifications ................3 2. Installation ..............4 What do you have ................4 Unpacking...................5 ACLD-9185's Layout..............6 Connector Pin Assignment............7 Power Source Selectable ..............8 Using Relay Output ..............9 Connection ................10 Product Warranty/Service ..........11 Contents • i... -
Page 4: How To Use This Guide
How to Use This Guide This manual is designed to help you use the ACLD-9185. The manual describes how to modify various settings on the ACLD-9185 card to meet your requirements. It is divided into five chapters: • Chapter 1, "Introduction," gives an overview of the product features. -
Page 5: Introduction
12V power bus. Normally the current driving capability of the 12V power source is not good enough . The ACLD-9185 has a jumper switch allowing the user to connect an external +12V power source. Introduction • i... -
Page 6: Features
1.1 Features The ACLD-9185 Relay Actuator and D/I Card provides the following advanced features: • 16 Single-Pole-Double-Throw relays • LED indicators to show activated relays • On-board relay driving circuits • 120V/1 Amp contact rating • Simple to program •... -
Page 7: Specifications
1.3 Specifications: Output Channels Relay Type 16 SPDT ( Form C ) Contact rating 120V AC/DC , 1 A Breakdown Voltage 1000 V AC/DC min.. Release time 5 msec max. Operate time 5 msec max.. Relay ON time 3 msec typical Relay OFF time 3 msec typical Total switching time... -
Page 8: Installation
Installation This chapter describes how to install the ACLD-9185. At first, the contents in the package and unpacking information that you should be careful are described. The jumpers setting for the ACLD-9185's base power source selection are also specified. 2.1 What You Have... -
Page 9: Unpacking
IC's to make sure that they are properly seated. Do this only with the module place on a firm flat surface. Note : DO NOT APPLY POWER TO THE CARD IF IT HAS BEEN DAMAGED. You are now ready to install your ACLD-9185. Installation • 5... -
Page 10: Acld-9185'S Layout
2.3 ACLD-9185's Layout +12V COM8 COM0 NO15 NC15 COM15 COM7 Figure 2.1 6 • Installation... -
Page 11: Connector Pin Assignment
2.3 Connector Pin Assignments The relationship between connector pins driver IC's, relay connects, LED's, and resistor arrays on the ACLD-9185 is shown in the following table: ULN2003 RELAY RELAY Contacts Resistor IN OUT Array U3 4 COM0 U3 5 COM1... -
Page 12: Power Source Selectable
2.5 Power Source Setting The ACLD-9185's power source can come from internal ( provided by PC bus) or external ( provided by external DC +12V). Both of internal and external source can provide +12V and +5V, respectively. The description of power source is specified as following table:... -
Page 13: Using Relay Output
2.6 Using Relay Output The ACLD-9185 contains 16 SPDT Form C relays, the connection of Form C realy is shown as the following diagram. Control Bit = High (1) Control Bit = Low (0) This relay has three contacts : NC ( Normal Close), NO ( Normal Open), and COM( Common). -
Page 14: Connection
2.7 Connection The ACLD-9185 is digital output daughter board which comes equipped with ACL series multi-function data acquisition cards and digital I/O card. The connection configurations of ACL series cards and the ACLD-9185 are shown as below. 2.7.1. Multi-function Cards and ACLD-8195... -
Page 15: Product Warranty/Service
Product Warranty/Service Seller warrants that equipment furnished will be free form defects in material and workmanship for a period of one year from the confirmed date of purchase of the original buyer and that upon written notice of any such defect, Seller will, at its option, repair or replace the defective item under the terms of this warranty, subject to the provisions and specific exclusions listed herein.
Need help?
Do you have a question about the ACLD-9185 and is the answer not in the manual?
Questions and answers