Advertisement
OPERATI
NG
Threading
the
Tape
l.
Depress
the standby key.
2.
Place
a
reel of
tape
on
the
supply
spindle
(2).
3.
Place
an
empty
reel
on
the
take-up spindle
(2).
4.
Unwind
approximately12 inches oftape
from
the
supply
reel, hold asection taut
and
insert
itinto
the
head
slot
opening.
5.
Insert
the
free
end
into one of the slots
in
the
take-up
reel.
Turn
the
take-up
reel
a
few com-
plete
revolutions to secure
the
tape
to
the
reel
and
to take
all
slack
up between
reels.
Playback
l.
Connect
the
outputs
of the preampliJier
being
used
to
the
inputs of
an
amplifier.
2.
Depress
the
Standby
key. It turns
the
AC
power
on and opens
the
head
assembly.
3.
Place the Selector Switch
or
Switches
in
play
position.
4.
Place
a reel
of tape
on left-hand supply reel,
and
thread
the
tape through the
head
slot
opening
and
between
the
capstan and
pressure roller.
Place an empty reel of the
same
size
on the
right-hand take-up reel and
turn
the
reel in
a
counterclockwise
direction
to
fasten
the
tape to
the
reel
and
to remove
all slack
between
reels.
5.
Switch
the Head
Selector
Switch
to 2-T
for
two
track
tape
and
to 4-T
for four track
tape.
6.
Placethe
rubberreel retainerson thereel
stand
hubs.
?.
Depressthespeed
keyforthe
desiredtapespeed.
8.
Depress the run
key.
9.
Adjust the volume
controls, on stereo record-
ings, until the
two
meters
are
balanced.
On
monaural recordings, adjust
the
volume control
to the desired
listening level.
Recording
l.
Connect the sound
source
to
be
recorded to
the
proper input receptacles
on
the
preamplifier.
2.
Thread
a blank tape onto the
transport.
3.
Depress
the
desired
speed
key.
4.
Set
the
Head Selector
Switch
to
2-T on
models
T-313 and
T-323
and
to
4-T on
models
T-333,
T-33?,
and
T-338.
The
four track
models
will
also record 2 track when
used
with blank or
bulk-erased
tape.
5.
Depress
the
interlock buttons, just to
the
left
of
the
record/
playback
head,
and move the
levers
tothe
rightto
place
thetransport
in
record oper-
ation.
6.
Adjust
the
volume
controls until the meters
are
I
NSTRUCTI
ONS
fluctuatingin
the
centeror upperhalf
of
the
black
area
for
7
l/
2 ips
speed.
Adjust
slightly
lower
for
3 3/ 4
ips
speed.
?.
Depress
the
Run
key.
8.
When
the recording
is finished,
set
the
selector
switches
to play
and
then depress
the
standby
key.
Rewind
To
rewind
a
tape, depress the key
with
the
arrow pointing toward
the
left.
Fast Forward
To
advance
the tape,
depress
the
key with
the
arrow pointing toward the right,
2
-Track
Monaural
Recording
l.
Thread
the
tape.
See
'Threading
the
Tape".
2.
Connect
the signal source
tothe
left
channel
in- _
pur.
-
a
tE
3.
place
the
left
channel
in record
position.
j F
NOTE: Keep the
right
channel
in
play
position
,i :,
and
the votume
turned
down.
.B
g
4.
Make
the
recording.
; F
5.
After the
recording
is
completed,
reverse the
P
-r
reelsl
rethread
the
tape,
and make
a
recording
!{ j.
on
the
other
half
of ttre
tipe.
"
B 6
6.
Toplay backthe recordings, usethe teitctrannet
P !
output.
€
f
4
-Track
Monaural
Recording
t,
d'
Ntl'i
I.
Thread
the
tape.
See
,Threading
the
Tape". 3
2.
Connect
thesignal source to
the
teft
channel
in-
put.
3.
Place
the
left
channel
in record
position.
NOTE:
Keep the
right
channel
in play position
and
the
volume
turned
down.
4.
Make
the recording.
5.
After
the
recording
is
completed,
reverse
the
reelsl rethread the tape and
make
a
second
recording.
6.
Place
the
left
channel
in play position
and
turn
the
volume
down.
?.
Connect
the signal source to the
right
channel.
B.
Reverse
the
reels, rethread
the
tape,
and
place
the
right
channel
in record
position.
9-
Make
the
recording.
p
10.
After
the
third_recording
is
completed,
reverse
E
reels, rethread
tape,
andmakefourthrecording.,i
Page
3
Advertisement
