IMPORTANT SAFETY INFORMATION Explanation of symbols used in this manual and on the product: This symbol is intended to alert the user to the presence of un-insulated dangerous voltages within the enclosure of sufficient magnitude to cause electric shock. This symbol is intended to alert the user to the presence of important maintenance and servicing information in the instruction and service manuals.
MAINS PLUGS This appliance is supplied with a non-rewireable mains plug for the intended country. Replacement mains leads can be obtained from your Linn retailer. Should you need to change the plug please dispose of it carefully. A plug with bared conductors is dangerous if engaged in a live socket.
Always ensure the fuse cover is fitted. If the fuse cover is missing do not use the plug. Contact your Linn retailer to obtain a replacement fuse cover. Fuses are for fire protection and do not protect against electric shock.
MAINS PLUG REPLACEMENT Should your mains plug need replacing and you are competent to do this proceed as follows. If you are in doubt contact your Linn retailer or a competent electrician. Disconnect the plug from the mains supply. Cut off the plug and dispose of it safely. A plug with bared conductors is dangerous if engaged in a live socket.
Page 6
The addition of any Linn component will improve the sound quality of your system. Linn has a policy of continuously improving its equipment allowing customers to retro-fit...
Page 7
Like any tuner, the KREMLIN will perform at its best when used with a good quality aerial. Please read the section on aerial installation.
INSTALLATION Unpack the unit and retain the packing for future transportation. CONTENTS KREMLIN Tuner Unit Mains Lead Owner's Manual and Registration Card 2 x Single Phono-Phono Leads 1 x Dual Phono-XLR Lead 2 x F-type aerial connector Spare Fuse WARNING Use the earthed moulded mains load supplied. Never use an unearthed plug or adaptor.
Page 9
AERIAL INSTALLATION The installation of a high quality aerial system is essential if the best possible performance is to be obtained from the KREMLIN tuner. However, the type of aerial system required for your location depends on a number of factors including the power and siting of transmitters, the proximity of hills and tall buildings and the presence of local interference sources.
CONNECTION The KREMLIN tuner has connectors for both an aerial installation and a cable system: AERIAL CONNECTION The aerial connector on the KREMLIN tuner is a standard co-axial F-type. If the lead from your aerial is fitted with this type of plug, simply screw the plug into the socket on the tuner until the connection is secure but not overtight.
AUDIO CONNECTIONS The KREMLIN has two identical stereo line outputs to enable connection to both the preamplifier of a main system and the distribution unit of a multi-room system, without the need for adapter cables.
REMOTE IN / OUT CONNECTIONS The wired remote in and out facility on the KREMLIN is designed for use in a distributed system (Knekt) which makes possible the remote operation of various Linn products throughout your home.
Page 13
Two small dashes will appear on the display and after a short delay, the display will show the setting at which the tuner was last used. The KREMLIN will then operate at the last used frequency.
Page 14
AERIAL To select either the aerial or the cable input, press the AERIAL button (or the 0 button on the remote control handset). When the aerial is selected, the display shows the legend AERIAL. TUNE To show the tuned frequency, press the TUNE button. The display shows the legend MHz and the frequency as a four or five digit number.
STORE To store a tuned frequency as a memory preset, press the STORE button. The display shows the number of the lowest empty preset memory. For example, preset 7 would be shown as St 7. If desired, select another preset number by pressing the [ + ] or [ –...
Page 16
NOTE The stations that have previously been stored in presets will be skipped by the autostore function. The autostore function is terminated when either the top of the tuning range has been reached or the highest numbered preset has been filled. The function can be terminated by pressing PRESET , TUNE , or SCAN .
Page 17
If the first digit entered is not within the valid tuning range of the KREMLIN, the display shows four dashes ( - - - - ) and then reverts to the original frequency. After the first valid digit, if subsequent entries would result in a frequency outside the tuning range, each digit entry is changed automatically to result in a valid frequency.
ADVANCED FEATURES USER SELECTABLE OPTIONS The user can customise operational features of the tuner to suit personal preferences. To do this, enter the user function mode. First, switch off the tuner. Press and hold either the MONO or the SIGNAL button and switch on the power. After a short time, the display will show U.
Page 19
USER FUNCTION 5 (U5) Option 0 connects the signal from the front panel remote control sensor to the REMOTE OUT socket. This allows the KREMLIN to act as a remote control receiver for other Linn equipment, which may be in a concealed location.
LOUDSPEAKERS Loudspeakers should be positioned according to manufacturers' instructions. They should be mounted on rigid stands, and not subject to any rocking movement. All Linn speakers except NEXUS and HELIX are designed to be placed close to the wall. CLEAN CONTACTS It is important that the electrical contacts in a hi-fi system are kept clean and mechanically sound.
Replace the fuse-holder, with the arrow pointing right, and snap the door shut. If the new fuse blows then there may be a fault with the KREMLIN and the complete tuner should be returned to your Linn dealer.
To help us serve you better in the future please return your completed warranty/ registration card to Linn or your national distributor. This will enable us to provide you with relevant product upgrade information and other news from Linn.
SPECIFICATIONS DIMENSIONS Width - 320mm Depth - 326mm Height - 80mm Weight - 4.7kg INPUTS AERIAL AND CABLE INPUTS - 75ohm unbalanced, F-type connector. Power supply for external RF amplifier, Voltage 13.7V current 40mA maximum (short-circuit protected). Supply can be switched to either or both RF inputs. REMOTE INPUT - current loop remote control input, Maximum DC current source - 40mA (short-circuit protected).