Related Manuals for Polar Electro PR-12
Summary of Contents for Polar Electro PR-12
- Page 1 Modular. Modular. Lighter. Lighter. Quicker. Quicker. Rev. 01 PR-12 Ground Mount Racking Solution PR-4 Ground Mount Installation Manual...
- Page 2 READ THIS ENTIRE DOCUMENT CAREFULLY BEFORE INSTALLING ALL REFERENCES TO PV PANELS, ELECTRICAL AND GROUNDING INSTRUCTIONS CONTAINED THIS MANUAL INFORMATION ONLY. CONSULT MANUFACTURER INSTALLATION INSTRUCTIONS THIRD PARTY DESIGN, ANCHORING, FOUNDATION INSTALLATION OF THE POLE MOUNT IS ALSO FOR INFORMATION ONLY - ALWAYS CONSULT A PROFESSIONAL CIVIL ENGINEER...
-
Page 3: Table Of Contents
Step 8: Install Horizontal Rails Step 9: Install Modules on Horizontal Rails 4.10 Step 10: Set Tilt Angle and torque all bolts 4.11 Step 11: Adjust tilt angle of Array Overview of PR-12 Assembly PR-12 REV01 (Release July 2014) Page 3 Page 3... -
Page 4: Introduction
1. Introduction 1.1 Product Overview 1.2 About This Manual 1.3 Product Liability The PR-12 Ground Mount is a versatile mounting solution for Subject This technical documentation is part of the product. any PV module. Polar Racking is not liable for damages resulting from failing... -
Page 5: Safety Considerations
DO NOT attempt any installation in adverse weather conditions (when high winds, rain, ice or snow is present). Remove any jewelery or other metallic adornments to avoid accidental electrical contact and use insulated tools. PR-12 REV01 (Release July 2014) Page 5... -
Page 6: Preparation
Torque Wrench (up to 150 ft lbs) and battery Torque Wrench (up to 150 ft lbs) and battery manual and drawings manual and drawings powered drill with 10mm Chuck. powered drill with 10mm Chuck PR-12 REV01 (Release July 2014) Page 6 Page 6... -
Page 7: Installation Instructions
4.1 Step 1 4.2 Step 2 4.3 Step 3 For the Polar PR-12 Top of Pole application, Lift strong back Place Six(6) Vertical Rails into the Clevis Supports on the A compass with a square edge can be used to initially locate onto pole and install Three U-Bolts, each with Two 1/2”... -
Page 8: Step 4: Attach Tilt Support Arms To Vertical Rails
Fig. 4 above. Slide the Horizontal Rail onto the Vertical Rails and loosely tighten the bolts. (Enough so that all Vertical Rails will tilt simultaneously when Tilt Arms are pushed forward). Page 8 Page 8 PR-12 REV01 (Release July 2014) -
Page 9: Step 7: Install M8 Bolts In Horizontal Rails
This ensures that the rails are square. loosened and adjusted to required position (Step 8). All rails should be left loose until modules are installed to ensure squareness. Page 9 Page 9 PR-12 REV01 (Release July 2014) -
Page 10: Step 10: Set Tilt Angle And Torque All Bolts
(Ensure a spacing of 6mm between all Modules) When Module is positioned correctly, torque each bolt to Ensure ALL connections are tightly secured and Torqued to 18ft lbs or 25Nm. correct specification. Page 10 Page 10 PR-12 REV01 (Release July 2014) -
Page 11: Overview Of Pr-12 Assembly
4. Installation Instructions PR-12 Top of Pole (Portrait Orientation) Page 11... - Page 12 11 Kodiak Crescent, Suite “C” Toronto, Ontario M3J 3E5 t: (416) 860-6722 www.polarracking.com info@polarracking.com...
Need help?
Do you have a question about the PR-12 and is the answer not in the manual?
Questions and answers