Table of Contents
Advertisement
General Operation
Using AC Mains
1 Check if the mains voltage, as shown on
the type plate located on the
back of the set, corresponds to your local
mains supply. If it does not, consult your
dealer or service center.
2
If your set is equipped with a voltage selec-
tor, adjust the selector so that it matches
with the local power supply.
3 Connect the mains lead to the AC ~ inlet
and the wall socket.The mains lead is now
connected and ready for use.
4 To switch the set off completely, withdraw
the mains lead from the wall socket.
•
Disconnect the mains lead from the wall
socket to protect your set during heavy
thunderstorms.
Helpful hints : To avoid unnecessary energy
consumption, always adjust the Source
selector to TAPE/OFF after using the set.
Also check that the tape deck keys are
released
The type plate is located on the back of
the set.
General operation
Switching on and off and selecting
functions
1 To switch on, push the Source selector
slider to CD, TUNER, or TAPE/OFF as
desired.
➜ In CD or TUNER, the display
lights up blue.
➜ In TAPE, the display lights up during tape
operation
2 To switch off, push the Source selector
slider to TAPE/OFF and check the cassette
keys are released.
Helpful hints:
– To change from TAPE to TUNER or CD
function, or when you are switching off the set:
first, make sure you press the tape
STOP•EJECT 9/ key to end playback and
all the cassette keys are released.
– The radio presets will be retained in the set's
memory.
Adjusting volume and sound
1 Adjust the volume with the VOLUME
control.
2 Press DBB once or more to select dynamic
bass boost on or off.
Digital Tuner
Digital tuner
Tuning to radio stations
1 Push the Source selector slider to
TUNER.
➜ The display lights up blue and if pro-
grammed, a preset number appears (see
3).
➜ Then, the display shows radio station fre-
quency and waveband. If programmed,
MEMORY appears. (see 4)
2 Press STOP/BAND 9 to select your
desired waveband, FM or MW.
• For FM, adjust MONO•STEREO to
STEREO.
3 Press and hold ∞ or § until the frequency
in the display starts running.
➜ The radio automatically tunes to a station
of sufficient reception.The frequency
keeps running during automatic tuning.
– STEREO lights up for stereo FM reception.
4 Repeat step 3 if necessary until you find the
desired station.
• To tune to a weak station, press ∞ or §
briefly and repeatedly until you have found
optimal reception.
To improve radio reception:
• For FM, extend, incline and turn the tele-
scopic aerial. Reduce its length if the signal is
too strong.
– To tune to a weak FM station, adjust
MONO•STEREO to MONO.
• For MW, the set uses a built-in aerial. Direct
this aerial by turning the whole set.
Programming radio stations
You can store up to a total of 20 radio stations
in the memory (10 FM and 10 MW), manually
or automatically (Autostore).
Manual programming
1 Tune to your desired station (see Tuning to
radio stations).
2 Press PROG to activate
programming.
➜ Display: P01. MEMORY flash.
3 Press ALBUM/PRESET -/+ once or more
to allocate a number from 1 to 10.
4 Press PROG to confirm.
5 Repeat steps 1-4 to store other stations.
Helpful hints: You can erase a preset station by
storing another frequency in its place.
Autostore
Autostore automatically starts programming
radio stations from preset 1. Any previous pre-
sets e.g. manually programmed will be erased.
1 In TUNER mode, press STOP/BAND 9
to select FM or MW.
2 Press and hold PROG until the frequency
and MEMORY flash.
➜ Available stations are programmed (FM
or MW. P and a preset number (1 - 10)
appears when a station is stored.
➜ After all stations are stored, the first auto-
store preset station automatically plays.
To listen to a preset station
Press the ALBUM/PRESET -/+ button once
or more until the desired preset station is dis-
played.
Advertisement
Table of Contents
