Cameo ZENIT Series Quick Start Manual

ZENIT DESIGN BRACKET
®
ZENIT DESIGN BRACKET FOR B60, P40, P130
IN BLACK AND CHROME
SAFETY INFORMATION
1. Please read these instructions carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.
5. Use the equipment only in the intended manner and for the intended purpose.
6. Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make
certain that wall mounts are properly installed and secured. Make certain that the equipment is
installed securely and cannot fall down.
7. During installation, observ e the applicable safety regulations for your country.
8. Never install and operate the equipment near radiators, heat registers, ovens or other sources
of heat. Make certain that the equipment is always installed so that is cooled sufficiently and
cannot overheat.
9. Never place sources of ignition, e.g., burning candles, on the equipment.
10. Ventilation slits must not be blocked.
11. This appliance is designed exclusively for indoor use, do not use this equipment in the immediate
vicinity of water (does not apply to special outdoor equipment - in this case, observe the special
instructions noted below). Do not expose this equipment to flammable materials, fluids or gases.
12. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers
filled with liquids, such as vases or drinking vessels, on the equipment.
13. Make certain that objects cannot fall into the device.
14. Use this equipment only with the accessories recommended and intended by the manufacturer.
15. Do not open or modify this equipment.
16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due
to tripping hazards.
17. During transport, make certain that the equipment cannot fall down and possibly cause property
damage and personal injuries.
18. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the
equipment or if it has been damaged in anot her way, switch it off immediately and unplug it from
the mains outlet (if it is a powered device). This equipment may only be repaired by authorized,
qualified personnel.
19. Clean the equipment using a dry cloth.
20. Comply with all applicable disposal laws in your country. During disposal of packaging, please
separate plastic and paper/cardboard.
21. Plastic bags must be kept out of reach of children.
MANUFACTURER'S WARRANTY & LIMITATION OF LIABILITY
You can find our current warranty conditions and limitation of liability at:
https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS-DECLARATIONS_CAMEO.pdf
To request warranty service for a product, please contact Adam Hall GmbH, Adam-HAll-Str. 1,
61267 Neu Anspach / Email Info@adamhall.com / 49 (0) 6081 / 9419-0
PROPER DISPOSAL OF THIS PRODUCT (WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT)
(Valid in the European Union and other European countries with waste separation)
This symbol on the product, or the documents accompanying the product, indicates that this appliance may
not be treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled
waste disposal. Please dispose of this product separately from other waste and have it recycled to promote
sustainable economic activity.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details on where and how they can recycle this item in an environmentally friendly manner.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product should not be mixed with other commercial wastes for disposal
INTRODUCTION
The CLZDB1 stand and assembly bracket is suitable for Cameo spotlights B60, P40 and P130 from
the Zenit series and it is available in black (CLZDB1B) as well as in a chrome look (CLZDB1C). Its
discreet and elegant shape makes it particularly suitable for use at design-focused events.
Spotlights are not included in the scope of delivery!
INSTALLATION
1. Disconnect the spotlight from the mains and carefully place it, front first, on a horizontal
surface.
2. Undo the two wing screws on the left and right of the spotlight and remove the original assem-
bly bracket from the spotlight housing.
3. Position the two plastic washers (A) with the round recess facing the spotlight onto the cylindri-
cally shaped socket (B) on the left and right of the spotlight housing.
4. Now slide the fork ends (C) of the design bracket onto the socket on the housing over the two
washers from the top and make sure that the slightly chamfered fork ends match the also slightly
chamfered washers (if necessary, replace washers with each other).
5. Position one washer each (D) on the M8 thread of the two handle screws (E) and use them to
secure the design bracket on the spotlight housing.
Adam Hall GmbH · Adam-Hall-Str. 1 · 61267 Neu-Anspach · Germany
Tel.: (+49) 60 81 / 94 19 0 · Fax: (+49) 60 81 / 94 19 1000 · eMail: mail@adamhall.com
Now position the spotlight in a suitable area on an even surface and use the handle screws to
adjust the direction of the beam as required. The bottom side of the bracket features ample rubber
rails to protect the contact surface. The center of the design bar foot features an M10 thread for
installing a cross beam. Suitable cross beam clamps are optionally available. Ensure that the
connections are tight and secure the spotlight to the dedicated fixing eyelet using a fixing cable.
Important safety information Overhead installation requires extensive experience,
including the calculation of workload limits and installed equipment, and periodic
safety checks of all installation materials and spotlights. If you are not qualified to do
so, do not try to complete installation yourself; get the assistance of a professional
company.
SPECIFICATIONS
Item No.: CLZDB1B / CLZDB1C
Product type Other Lighting Accessories
Type Bracket
Colour Black
Controls 2 x M8 handle screws for adjusting the beam direction
Material Metal
Width 248 mm
Height 204 mm
Depth 191 mm
Accessories (included) 2 x plastic spacers, 2 x M8 grip screws incl. spacers
Weight 1.8 kg
E
D
B
A
C