Advertisement
.
Connection precautions
1. Disconnect the power supply before installation or maintenance of the light.
2. It is strictly mandatory to connect the earth cable (Yellow / Green) with the ground connection of the installation.
3. Do not touch the power source when the lamp is in operation.
4. To avoid damage, electric shock or fire, do not disassemble or replace the lamp (PCB CHIP LED).
5. To avoid damage, falls, electric shocks or fires, please do not modify or replace the original accessories with others that are not,
without consulting and being authorized by Venalsol beforehand.
6. Only qualified personnel can perform the replacement or installation of the luminaire and make sure that it follows the
instructions in the manual. If the installation is not carried out properly, it can cause falls, electric shocks, fires or other damages.
7. Disconnect the power supply if smoke or odor comes out, as this could result in a fire or electric shock.
8. Consult qualified personnel for inspection and maintenance of the lamp
9. If the wiring of the luminaire itself is damaged, it can only be replaced by Venalsol.
Applicable regulations
It has passed the tests and verifications necessary to obtain the CE Marking. This product complies with
the application standards on Low Voltage (LVD) 2014/35 / EU: EN60598-1: 2015, EN60598-2-24: 2013,
EN60598-2-1: 1989, EN62031: 2008, EN62471: 2008, EN62493: 2010 and Electromagnetic Compatibility
(EMC) 2014/30 / EU: EN61000-3-2: 2014, EN61000-3-3: 2013, EN61547: 2009, EN55015: 2013
This symbol indicates that the product at the end of its useful life should be removed separately from
other waste, since it is identified as an appliance for electrical use or domestic appliance according to
Royal Decree 208/2005. Therefore, at the end of the use, you must take charge of delivering the
product to a selective collection center or to an authorized waste manager. Venalsol is registered in the
National Registry of Electrical and Electronic Devices with registration number 3493 and is attached to a
Waste Management System for Electrical and Electronic Devices for products with the category of
"lighting devices".
LED Venalsol luminaires are respectful with the environment. They do not contain mercury and the
electronic components used comply with the provisions of the RoHS regulations transposing Royal
Decree 208/2005.
Tecnical parameters
Product specifications
50W
Input voltage
CRI
Beam angle
Classification IP
Dimensions
280x137x102mm
Luminaire net weight
1.9 ±0.3kg
Power factor
Useful life
Operating temperature
Operating humidity
Storage temperature
100W
150W
200W
AC100-277V 50/60Hz Clase I ( Needs grounding )
Ra80
30ºX70º, 50ºX90º, 120º, 40ºX120º, 90º
IP65
486x137x102 mm
718x137x102mm
948x137x102mm
3.4 ±0.3kg
4.7 ±0.3kg
5.7 ±0.3kg
>0.93
≥50000Hrs (LM70@35°C)
-30- +50°C
15%~90%RH
-40- +70°C
Installation instructions
A. Typology, connection and installation of the hanging cable
2. Pull on
B. Adjustable surface installation
Dimensions
240W
1178x274x102mm
6.9 ±0.3kg
A
B
C
50W
137
280
102
C
100W
137
486
102
150W
137
718
102
200W
137
948
102
A
240W
274
1178
102
Measures expressed in millimeters
IT IS RECOMENDED TO INSULATE AND ATTACH THE TERMINATIONS OF THIS
Brown
Blue
Yellow/Green
1. Press
1. Insert
B
IMPORTANT – DIM CONNECTION 1-10Vcc
CONNECTION IF REGULATION IS NOT USED
Brown
Blue
1. Enter tie
Ajustable range 40 - 544mm
Advertisement
