1. Manuals
  2. Brands
  3. Lex Manuals
  4. Industrial PC
  5. 3I380NX
  6. User manual

Lex 3I380NX User Manual

Intel bay trail-i e3845 quad core/on board/socket ddr3l, 4 x intel i210it lan/usb/vga/hdmi all-in-one intel bay trail-i e3845 1.91 ghz/vga, hdmi, com, pcie mini card multi-lan board, sata, usb
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
3I380NX
Intel Bay Trail-I E3845 (Quad Core ) /
On Board / Socket DDR3L, 4 x Intel I210IT LAN /
USB / VGA / HDMI
All-In-One
Intel Bay Trail-I E3845 1.91 GHZ /
VGA, HDMI, COM, PCIe mini card
Multi-LAN Board, SATA, USB
NO. 3I380NX_V0.1
Release date: May. 08. 2015

Advertisement

Table of Contents
loading

Summary of Contents for Lex 3I380NX

  • Page 1 3I380NX Intel Bay Trail-I E3845 (Quad Core ) / On Board / Socket DDR3L, 4 x Intel I210IT LAN / USB / VGA / HDMI All-In-One Intel Bay Trail-I E3845 1.91 GHZ / VGA, HDMI, COM, PCIe mini card Multi-LAN Board, SATA, USB NO.

  • Page 2: Table Of Contents

    Contents 3I380NX Warning!........................... Hardware Notice Guide ...................... CHAPTER 1 GENERAL INFORMATION ................. 1-1 MAJOR FEATURE........................ 1-2 SPECIFICATION ........................1-3 DIRECTIONS FOR INSTALLING THE MINI CARD ............. 1-4 PACKING LIST ........................CHAPTER 2 HARDWARE INSTALLATION ................2-1 UNPACKING PRECAUTION ....................2-2 UNPACKING CHECKUP ......................
  • Page 3 3-19 CONNECTOR WAFER OF COMPATIBLE BRAND AND PART NUMBER LIST ......CHAPTER 4 INTRODUCTION OF BIOS ..................4-1 ENTER SETUP ..........................4-2 BIOS MENU SCREEN & FUNCTION KEYS ................. 4-3 GENERAL HELP ........................... 4-4 MENU BARS ..........................4-5 MAIN .............................. 4-6 ADVANCED ...........................
  • Page 4 1-1 IO DEVICE : F75111 UNDER WINDOWS ..................1-2 IO DEVICE : F75111 VB6 UNDER WINDOWS ................1-3 IO DEVICE : F75111 UNDER LINUX ..................... APPENDIX D: CPC-CAR POWER CONTROL (OPTION) ..............
  • Page 5 Copyright This manual is copyrighted and all rights are reserved. It does not allow any non authorization in copied, photocopied, translated or reproduced to any electronic or machine readable form in whole or in part without prior written consent from the manufacturer.

  • Page 6: Warning

    Warning ! Battery Batteries on board are consumables. The life time of them are not guaranteed. 2. Fless solution with HDD The specifi cation & limitation of HDD should be considered carefully when the fanless solution is implemented. We will not give further notifi cation in case of changes of product information and manual.

  • Page 7: Hardware Notice Guide

    Hardware Notice Guide 1. Before linking power supply with the motherboard, please attach DC-in adapter to the motherboard fi rst. Then plug the adapter power to AC outlet. Always shut down the computer normally before you move the system unit or remove the power supply from the motherboard.
  • Page 8 Photo 1 Insert Unplug...

  • Page 9: Chapter 1 General Information

    BIOS, these are perfect control board for networking purpose. 3I380NX also supports multiple COM ports of fi ve RS232 and one RS422/485 to meet the needs of connectivity for multiple COM ports. It supports up to four serial ports (RS232 or RS485), and 7 ports of USB (1 port of USB3.0 and 2 ports of USB 2.0 in rear side &...

  • Page 10: Major Feature

    1-1 Major Feature INTEL Atom Processor Baytrail-I E3845 Onboard DDR3L 4GB; data transfer rates of 1333 MT/s Support 4 x PoE LAN follows IEEE 802.3af standard Support extended 2 x Mini PCIe card Support up to 2 SATA ports (shared with mSATA) Hardware digital Input &...

  • Page 11: Specification

    1-2 Specifi cation SoC: INTEL Atom Processor Baytrail-I E3845 Memory: Onboard DDR3L 4GB, data transfer rates of 1333 MT/s Graphic / Video: Intel's 7th generation (Gen 7) graphics and media encode/decode engine. SATA: Integrated Serial ATA Host Controller Up to 2 SATA ports: All ports support 2.0 Data transfer rates up to 3.0 Gb/s (600 MB/s).

  • Page 12: Directions For Installing The Mini Card

    1-3 Directions for installing the Mini Card 1. Unscrew the screw on the board 2. Plug in the Mini Card in a 45 angle 3. Gently push down the Mini Card and screw the screw back.

  • Page 13: Packing List

    Quantit 7G1901-1561002-0 MB-3I380NX-I44-00-002 LF,3I380NX-I44-00,Rev.:002 6G8001-2195-0400 Manual LF,M/B,3I380NX 6G8006-2349-0100 LEX Product Driver DVD LF, Intel Baytrail Driver,Windows 7/8.1 32/64 6G6003-7350-0100 Power Cable LF, 2.0 2*4/DC JK,L=9cm *The packing list above is for the users who purchase single motherboard. The users who purchase the board with chassis may refer to the packing list in the Assembly Guide.

  • Page 14: Chapter 2 Hardware Installation

    Chapter-2 Hardware Installation 2-1 Unpacking Precaution This chapter provides the information how to install the hardware of 3I380NX Please follow section 1-4, 2-1 and 2-2 to check the delivery package and unpack carefully. Please follow the jumper setting procedure. NOTE! 1.

  • Page 15: Unpacking Checkup

    2-2 Unpacking checkup First of all, please follow all necessary steps of section 2-1 to protect 3I380NX from electricity discharge. With reference to section 1-4 please check the delivery package again with following steps: 1. Unpack the 3I380NX board and keep all packing material, manual and driver disc etc, do not dispose ! 2.

  • Page 16: Dimension

    2-3 Dimension-3I380NX...

  • Page 17: Layout

    2-4 Layout-3I380NX BAT1 MPCE2 CU41 CU42 MPCE1 CBT1 CPO1 SWP1 FAN1 CFP1 (Bottom side) CU43 JBS1 CU44 CIO2 (Bottom side) CIO1 MSD1 (Bottom side) CC11 CKM1 SIM1 (Bottom side) HDM1 CG11 CPI13 CPI15...

  • Page 18: Diagram

    2-5 Diagram- 3I380NX BAT1 MPCE2 CU41 CU42 MPCE1 CBT1 CPO1 SWP1 FAN1 CFP1 CU43 JBS1 CU44 CIO2 CIO1 CC11 CKM1 HDM1 CG11 CPI13...

  • Page 19: Bottom Side Diagram

    2-5-1 Bottom Side Diagram- 3I380NX SATA2 SATA1 MSD1 SIM1 BACK Panel-3I380NX LAN1 LAN4 LAN3 LAN2 HDMI...

  • Page 20: List Of Jumpers

    2-6 List of Jumpers JSB1: CMOS clear select JVL1: LCD panel power select (Option) SC1: CPC defa ult setting ( 1-2 ON ) (Option) 2-7 Jumper Setting Description A jumper is ON as a closed circuit with a plastic cap covering two pins. A jumper is OFF as an open circuit without the plastic cap.

  • Page 21: Coms Data Clear

    2-8 CMOS Data Clear A battery must be used to retain the motherboard confi guration in CMOS RAM. Close Pin1 and pin 2 of JSB1 to store the CMOS data. To clear the CMOS,follow the procedures below: 1. Turn off the system and unplug teh AC power 2.

  • Page 22: Jvl1: Lcd Panel Power Select (Option)

    2-9 JVL1: LCD panel power select (Option) JVL1 Description +3.3V *2-3 Note: Attention ! Check Device Power in spec JVL1 (Option) *+3.3V 2-10 SC1: CPC default setting ( 1-2 ON ) (Option) Mode select CPC function CPC Enabled Auto Down CPC Disabled Down Manual...

  • Page 23: Connection

    Chapter-3 Connection This chapter provides all necessary information of the peripheral's connections, switches and indicators. Always power off the board before you install the peripherals. 3-1 List of Connectors CPI13: DC-In 2x4 pin (2.0mm) Red Wafer connector CPI15 DC-In 2x5 pin (2.0mm) Red Wafer connector (Option) BAT1 Li 3V battery holder CBT1...

  • Page 24: Dc Power Input

    3-2 DC power input CPI13: DC-IN Internal Connector (2x4 pin 2.0mm Wafer ) PIN NO. Description PIN NO. Description DC-IN(12V) DC-IN(12V) DC-IN(12V) DC-IN(12V) Note: 1. Very important check DC-in Voltage type for 12V or 9~36V model spec *2. Because the system support PSE function, Check the total power consumption of the system used to select safe power cables, please refer to UL1007 specifi...

  • Page 25: Battery Input

    3-3 Battery Input BAT1: 3V Battery hold 2pin BAT1: Battery use Li 3V / 48mAh (BR1225) Note: 1. When board without Adaptor plug in,this board power RTC consumption about 2.7uA 2. If adaptor always plug in RTC power consumption about 0.1uA CBT1 Ext.

  • Page 26: Front Panel & Fan

    3-5 Front panel & FAN CFP1 Front panel LED connector (2x6pin 2.00mm wafer) PIN NO. Description PIN NO. Description Power LED+ HD_LED- HDD LED+ LAN1 LED- LAN1 LED+ LAN2 LED- LAN2 LED+ LAN3 LED- LAN3 LED+ LAN4 LED- LAN4 LED+ SWP1 Power button connector (1x2pin 2.0mm wafer) PIN NO.

  • Page 27: Display Interface

    3-6 Display interface CG1: DSUB VGA connector (DB15 pin) PIN NO. Description PIN NO. Description PIN NO. Description GREEN DDC DATA BLUE H-SYNC V-SYNC DDC CLOCK CG11: VGA wafer connector (2x5pin 2.0mm) PIN NO. Description PIN NO. Description BLUE DDC CLOCK GREEN V-SYNC H-SYNC...
  • Page 28 LVDS1: LVDS interface (2x15 pin 1.25mm wafer) (Option) PIN NO. Description PIN NO. Description PWM dimming +LCD(5V or 3.3V) +LCD(5V or 3.3V) Channel-1-DATA3+ Channel-0-DATA3+ Channel-1-DATA3- Channel-0-DATA3- Channel-0-DATA2+ Channel-0-CLK+ Channel-0-DATA2- Channel-0-CLK- Channel-0-DATA1+ Channel-0-DATA0+ Channel-0-DATA1- Channel-0-DATA0- +LCD(5V or 3.3V) +LCD(5V or 3.3V) Channel-1-DATA2+ Channel-1-CLK+ Channel-1-DATA2-...

  • Page 29: Touch Screen Device (Option)

    3-7 Touch screen device (Option) CT1: Touch screen (2x5 pin 2.0mm wafer) USB interface For 8- wire type pin defi ne PIN NO. Description PIN NO. Description Bottom Bottom Sense Top Sense Right Right Sense Left Left Sense Note: 1. For eight wire type cable Pin 3 and Pin4 need short. 2.

  • Page 30: Audio Interface

    3-8 Audio interface CA3: Mic in/Line in/Line out wafer connector (2x5pin 2.00mm wafer) PIN NO. Description PIN NO. Description LINEOUT_R MIC_IN LINE_IN_R SPDIF_O LINE_IN_L LINEOUT_L MIC_IN 3-9 Audio Amplifi er (Option) CALR1: Amplifi er Line-out Right/Left channel (1x4pin 1.25mm wafer) PIN NO.

  • Page 31: I/O Interface

    3-10 I/O Interface COM ports (COM1~COM4 from super I/O) COM1~4 default support RS232 mode COM1 RS232 or RS485 or RS422 form BIOS select RS232 mode ports (2x5pin 2.0mm Wafer) CC11: COM1 CC2: COM2 CC3: COM3 CC4: COM4 PIN NO. Description PIN NO.

  • Page 32: Digital Input / Output

    3-11 Digital Input / Output CIO1 DIO 0 ~ 3 (2x5pin 2.0mm wafer) PIN NO. Description PIN NO. Description DI-0 DO-3 DI-1 DO-2 DI-2 DO-1 DI-3 DO-0 Note: 1. DI pin default pull up 10KΩ to +5V 2. If use need isolate circuit to control external device 3.

  • Page 33: I C Bus Interface

    3-12 I C Bus Interface CO1: I C (SM) bus connector (1x4pin 1.25mm wafer) PIN NO. Description +3.3V SMB_CLK SMB_DATA pin1 3-13 PS2 KB/MS CKM1: KB/MS port (1x6pin 1.25mm wafer) PIN NO. Description KB/DAT KB/CLK MS/DAT MS/CLK pin1 CKM1 3-14 LAN Interface CL1 / CL2 / CL3 / CL4: LAN Giga/100Mb (RJ45 Jack) PIN NO.

  • Page 34: Usb Interface

    CL11/CL21/CL31/CL41: LAN port Giga /100Mb( 2x4pin 2.0mm wafer) (Option) PIN NO. Description PIN NO. Description TR0- / TX- TR0+ / TX+ TR2+ / NC TR1+ / RX+ TR1- / RX- TR2- / NC TR3- / NC TR3+ / NC 3-15 USB Interface CU1 / CU2: USB1/2 ports ( USB Type A connector ) PIN NO.
  • Page 35 CU3: Signal USB3.0/2.0 port (USB Type A 90°connector) PIN NO. Description PIN NO. Description USB3.0 RX- USB 2.0 D- USB3.0 RX+ USB 2.0 D+ USB3.0 TX- USB3.0 TX+ Note: 1. USB 3.0 and USB 2.0 signal connector CU41 / CU42 / CU43 / CU44: Internal USB ports (1x4pin 1.25mm wafer) PIN NO.

  • Page 36: Sata Interface

    3-16 SATA interface SATA1: SATA1 / SATA2 connector PIN NO. Description DATA TX+ DATA TX- DATA RX- DATA RX+ Note: 1. SATA1 support SATA 2.0 spec update 3Gb/sec. 2. CPO1 provide SATA HDD power +12V, GND, +5V 3. SATA1 / SATA2 share with mini card mSATA signal. SSD use SATA port 2 channel Note: 1.

  • Page 37: Module & Sim Socket

    3-17 Module & SIM socket Mini card & SIM card MPCE1/MPCE2: Support USB , mSATA interface (Mini card socket 52pin) PIN NO. Description PIN NO. Description +3.3V +1.5V SIM Power SIM Data PCIe-CLK- SIM CLK PCIe-CLK+ SIM Reset SIM RFU RST- PCIe-RX-/mSATA-RX+ +3.3V...

  • Page 38: Microsd Card Interface (Socket Push-Push)

    SIM1: SIM card socket pin defi ne is follow ISO 7816-2 smart card standard. PIN NO. Description PIN NO. Description DATA Note: 1. MPCE1 Pin 8, 10,12,14,16 for SIM1 card reader use. MSD1 SIM1 3-18 MicroSD Card interface (Socket Push-Push) PIN NO.

  • Page 39: Connector Wafer Of Compatible Brand And Part Number List

    3-19 Connector wafer of Compatible Brand and part number list Location CKTS PITCH Brand Name Mating connector Cable housing 2x5 10Pin 2.0mm B10B-PHDSS PHDR-10VS CALR1 1x4 4Pin 1.25mm MOLEX 53047-0410 51021-0400 CG11 2x5 10Pin 2.0mm B10B-PHDSS PHDR-10VS CC11 2x5 10Pin 2.0mm B10B-PHDSS PHDR-10VS...

  • Page 40: Introduction Of Bios

    Chapter-4 Introduction of BIOS The BIOS is a program located in the Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gains control. The BIOS fi rst operates an auto-diagnostic test called POST (Power on Self Test) for all the necessary hardware, it detects the entire hardware devices and confi...

  • Page 41: Bios Menu Screen & Function Keys

    4-2 BIOS Menu Screen & Function Keys In the above BIOS Setup main menu of, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us fi rst see a short description of the function keys you may use here: Press ←→...

  • Page 42: General Help

    4-3 General Help Status Page Setup Menu/ Option Page Setup Menu Press F1 to pop up a help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press <Esc>...

  • Page 43: Menu Bars

    4-4 Menu Bars There are six menu bars on top of BIOS screen: Main To change system basic confi guration Advanced To change system advanced confi guration Security Password settings Power PME & Power button settings Boot Exit Save setting, loading and exit options. User can press the right or left arrow key on the keyboard to switch from menu bar.

  • Page 44: Advanced

    4-6 Advanced Boot Confi guration Please refer section 4-6-1 PCI Express Confi guration Please refer section 4-6-2 USB Confi guration Please refer section 4-6-3 Video Confi guration Please refer section 4-6-4 Thermal Confi guration Please refer section 4-6-5 SATA Confi guration Please refer section 4-6-6 Console Redirection Please refer section 4-6-7...

  • Page 45: Boot Configuration

    4-6-1 Boot Confi guration Numlock Select Power-on state for Numlock, default is <ON> 4-6-2 PCI Express Confi guration PCIe 1/2/3/4 confi guration settings...

  • Page 46: Pci Express Root Port 1/2/3/4

    4-6-2-1 ► PCI Express Root Port 1/2/3/4 Control the PCI Express Root Port. The optional settings are: Enabled(default), Disabled. Select PCI Express port speed. The optional settings are: Gen1(default), Gen2 Select PCIE TXE ROM support The optional settings are: Disabled(default), Enabled...

  • Page 47: Usb Configuration

    4-6-3 USB Confi guration XHCI Mode Mode of operation of xHCI controller. The optional settings are: Best Auto(default), Enabled, Disabled.

  • Page 48: Video Configuration

    4-6-4 Video Confi guration Confi gure CRT as Enable or disable CRT function. The optional settings are: CRT(default) or Default Confi gure DDI0 as Enable or disable HDMI function. The optional settings are: HDMI(default) or disabled. Aperture Size The optional settings are: 128MB, 256MB(default), 512MB. IGD - DVMT Pre-Allocated Use this item to select DVMT 5.0 pre-allocated (fi...

  • Page 49: Thermal Configuration

    4-6-5 Thermal Confi guration Thermal Confi guration Parameters This Value controls the temperature of the ACPI Critical Trip Point, the point in which the OS will shutdown the system. Critical Trip point is the shutdown temperature, the default value is 110˚ The CPU frequency will auto reduce when cpu temperature arrived to passive Trip point.

  • Page 50: Sata Configuration

    4-6-6 SATA Confi guration SATA Controller Use this item to Enable or Disable SATA Device. The optional settings are: Enabled(default) or Disabled Chipset SATA Mode Determine how SATA controller(s) operate. The optional settings are: IDE Mode(default), AHCI Mode. SATA Speed Indicates the maximum speed the SATA controller can support.

  • Page 51: Console Redirection

    SATA Port 0 Connected to an ODD Use this item to Enable or Disable SATA Port0 ODD function The optional settings are: Enabled(default) or Disable SATA Port 1 Connected to an ODD Use this item to Enable or Disable SATA Port1 ODD function The optional settings are: Enabled(default) or Disable 4-6-7 Console Redirection Console Serial Redirect...

  • Page 52: Acpi Table/Fetures Control

    Data Bits The optional settings are: 8 Bits(default) , 7 Bits Parity The optional settings are: None(default) , Even , Odd Stop Bits The optional settings are: 1 Bit(default) , 2 Bits Flow Control The optional settings are: None(default) , RTS/CTS , XON/XOFF 4-6-8 ACPI Table/Fetures Control ACPI Table/Features Control Select ACPI sleep state the system will enter when the SUSPEND button is pressed.

  • Page 53: Security

    4-7 Security Supervisor Password To set up an Supervisor password 1. Select Supervisor Password. The screen then pops up an Create New Password dialog. 2. Enter your desired password that is no less than 3 characters and no more than 10 characters. 3.

  • Page 54: Power

    4-8 Power Wake on PME Determines the action taken when the system power is off and the PCI power management Enable wake up event occurs. The optional settings: Enabled, Disabled(default) Wake on Touch (Option) The optional settings: Enabled, Disabled(default) Note.wake on Touch panel , only support S3 mode. Power Button Instant OFF(default) : The system will be turn off directly when push the power button.

  • Page 55: Boot

    4-9 Boot Boot type Select boot type for Dual type ,Legacy boot type or UEFI boot type, default is Dual boot type Quiet Boot The optional settings are: Enabled(default), Disabled. EFI / Legacy Device order Determine EFI device fi rst or legacy device fi rst. The optional settings: EFI device fi...

  • Page 56: Legacy

    4-9-1 Legacy Normal Boot Menu Select Normal Boot option priority or Advance Boot option priority. The optional settings: Normal(default), Advance 4-9-2 Boot Type Order Boot Type Order Setting the boot type priority. The default settings is 1.USB drive 2.Hard Disk Drive 3.CD/DVD ROM drive 4.Others...

  • Page 57: Exit

    4-10 EXIT Exit Saving Changes This item allows user to reset the system after saving the changes. Save Change Without Exit This item allows user to saving the changes but doesn’t restart. Exit Discard Changes This item allows user restart the system but no saving the changes Load Optimal Default Use this item to restore the optimal default for all the setup options.

  • Page 58: Device Manager

    4-11 Device Manager Please press the key F10 when bootup to go into the Device Manager menu Serial Port 1/2 Confi guration Please refer section 4-11-1 Serial Port 3/4/5/6 Confi guration Please refer section 4-11-2...

  • Page 59: Sio Fintek8180U

    4-11-1 SIO FINTEK81801U Serial Port 1/2 Use this item to enable or disable serial port (COM1,COM2) The optional settings are: Enabled(default), Disabled. Serial Port 1 Base IO Address / Interrupt / Serial Mode Use this item to select an optimal setting for super IO device. The optional settings are: IO=3F8h;...
  • Page 60 Serial Port 2 Base IO Address / Interrupt / Serial Mode Use this item to select an optimal setting for super IO device. The optional settings are: IO=2F8h; IRQ=3(default) IO=2E8h; IRQ=3,4 IO=3E8h; IRQ=3,4 IO=3F8h; IRQ=3,4 Serial Mode RS232 driver(default) : When hardware select to RS232 or RS422 mode, please enter to RS232 driver.

  • Page 61: Hardware Monitor

    4-11-2 Hardware Monitor Press [Enter] to view PC health status. This section shows the status of your CPU, Fan, and overall system. This is only available when there is Hardware Monitor function onboard.

  • Page 62: Sio Fintek81216D/Dg

    4-11-3 SIO FINTEK81216D/DG Serial Port 3/4 Use this item to enable or disable serial port (COM3, COM4, COM6 for Touch). The optional settings are: Enabled(default), Disabled. Serial Port 3 Base IO Address / Interrupt Use this item to select an optimal setting for super IO device. The optional settings are: IO=3E8h;...
  • Page 63 Serial Port 4 Base IO Address / Interrupt Use this item to select an optimal setting for super IO device. The optional settings are: IO=2E8h; IRQ=10(default) IO=2F8h; IRQ=3,4,5,6,7,10,11 IO=3F8h; IRQ=3,4,5,6,7,10,11 IO=3E8h; IRQ=3,4,5,6,7,10,11 IO=4F8h; IRQ=3,4,5,6,7,10,11 IO=4E8h; IRQ=3,4,5,6,7,10,11 Serial Mode RS232 driver(default) : When hardware select to RS232 or RS422 mode, please enter to RS232 driver.

  • Page 64: Chapter 5 Driver Installation

    Chapter-5 DRIVER INSTALLATION There is a system installation DVD in the package. This DVD does not only include all the drivers you need but also some other free application programs and utility programs. In addition, this DVD also includes an auto detect software telling you which hardware is installed and which driver is needed so that your system can function properly.
  • Page 65 AUTOMATIC DRIVER INSTALLATION menu...
  • Page 66 1. INF Install Intel Baytrail chipset driver 2. VGA Install onboard VGA driver 3. Serial IO Install Serial IO driver (FOR Win 7 only) 4. xHCI Install Intel USB 3.0 xHCI driver (FOR Win 7 only) 5. HD Audio Install HD Audio Codec driver 6.

  • Page 67: Inf Install Intel Baytrail Chipset Driver (Example For Win8 64Bit)

    5-1 INF Install Intel Baytrail Chipset Driver (example for WIN8 64bit) 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Intel® Chipset Device menu"screen, click "INF". Software"screen, click "Next". 3. At the "License Agreement" screen, 4. At the "Readme File Information" click "Yes".
  • Page 68 6. Click "Finish" & restart computer. 5. Click "Next" NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 64/32-bit, X:\driver\INTEL\BAY\INF\WIN7\infi nst_autol.exe For Windows 8 / 8.1 32/64-bit X:\driver\INTEL\BAY\INF\WIN_8_64\infi nst_autol.exe...

  • Page 69: Vga Install Intel Baytrail Vga Driver (Example For Win8 64Bit)

    5-2 VGA Install Intel Baytrail VGA Driver (example for WIN8 64bit) 1. At the"AUTOMATIC DRIVER INSTALLATION 2. At the "Welcome to the Setup Program menu"screen, click "VGA". screen, Click "Next". 3. At the "License Agreement" screen, 4. At the "Readme File Information" Click "Yes"...
  • Page 70 6. Click "Finish" to restart computer 5. At the "Setup Progress" screen, Click "Next". NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32-bit, X:\driver\INTEL\BAY\VGA\WIN_7_32\Setup.exe For Windows 7 64-bit X:\driver\INTEL\BAY\VGA\WIN_7_64\Setup.exe For Windows 8 / Windows 8.1 32-bit X:\ \driver\INTEL\BAY\VGA\WIN_8_32\Setup.exe For Windows 8 / Windows 8.1 64-bit X:\driver\INTEL\BAY\VGA\WIN_8_64\Setup.exe...

  • Page 71: Serial Io Install Driver Baytrail Serial Io Driver (For Windows 7 Only)

    5-3 Serial IO Install Driver Baytrail Serial IO Driver (FOR Windows 7 only) 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Welcome to the Setup Program menu" screen, click "Serial IO". screen, Click "Next". 3. At the "License Agreement" screen, 4.
  • Page 72 5. At the "Ready to install the program" screen, 6. Click "Finish" and restart computer Click "Install" NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32-bit, X:\driver\INTEL\BAY\SERIALIO\WIN7_32Bit.msi For Windows 7 64-bit X:\driver\INTEL\BAY\SERIALIO\Win7_64Bit.msi...

  • Page 73: Xhci Install Intel Usb 3.0 Xhci Driver (For Windows 7 Only)

    5-4 xHCI Install Intel USB 3.0 xHCI Driver (FOR Windows 7 only) 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Welcome to the Setup Program menu" screen, click "xHCI". screen, Click "Next". 3. At the "License Agreement" screen, 4. At the "Readme File Information" screen, Click "Yes".
  • Page 74 6. Click "Finish" to restart computer 5. At the "Setup Progress" screen, Click "Next". NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32 / 64-bit, X:\driver\INTEL\BAY\XHCI\Driver_Installer\Setup.exe...

  • Page 75: Hd Audio Install High Definition Audio Driver (Example For Win 64Bit)

    5-5 HD Audio Install High Defi nition Audio Driver (example for WIN8 64bit) 1. At the "AUTOMATIC DRIVER INSTALLATION 2. Click" Next". menu", click "HD Audio" 3. Click "Finish" to restart computer NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32 / 64-bit, Windows 8/8.1 32 / 64-bit X:\driver\INTEL\BAY\SOUND\Win7_Win8_Win81_R273.exe...

  • Page 76: Mbi Install Intel Mbi Driver (For Win 8/8.1 Only)

    5-6 MBI Install Intel MBI Driver (FOR Win 8/8.1 only) 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Welcome to the Setup Program menu", click "HD Audio". screen, Click "Next". 3. At the "License Agreement" screen, 4. At the "Setup Progress" screen, Click "Next". Click "Yes".
  • Page 77 5. Click "Finish" to restart computer NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 8/8.1 32 / 64-bit, X:\driver\INTEL\BAY\MBI\Setup.exe...

  • Page 78: Txe Lnstall Intel Txe Driver

    5-7 TXE Install Intel TXE driver 5-7-1 TXE Install for WIN8/WIN8.1 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Setup" screen, Click "Next". menu", click "TXE". 3. At the "License Agreement" screen, 4. Click "Next". Click "Yes".
  • Page 79 5. Click "Finish" & restart computer NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 8 32 / 64-bit, X:\driver\INTEL\BAY\TXE\WIN_8\SetupTXE.exe For Windows 8.1 32 / 64-bit, X:\driver\INTEL\BAY\TXE\WIN_8.1\SetupTXE.exe...

  • Page 80: Txe Install For Win7

    5-7-2 TXE Install for WIN7 Please install PXE Patch fi rst. 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Windows Update" screen, menu", click "TXE Patch". Click "Yes". 3. Click “Finish” & restart computer 4. At the "AUTOMATIC DRIVER INSTALLATION menu", click "TXE "...
  • Page 81 5. At the "TXE Setup" screen, Click "Next". 6. At the "License Agreement" screen, Click "Yes". 8. Click "Finish" & restart computer 7. Click "Next". NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32 / 64-bit, TXE Patch X:\driver\INTEL\BAY\TXE\WIN_7\kmdf-1.11-Win-6.1-x86.msu X:\driver\INTEL\BAY\TXE\WIN_7\kmdf-1.11-Win-6.1-x64.msu...

  • Page 82: How To Update Ami Bios

    (Storage device could be USB FDD or USB pen drive.) STEP 2. Copy utility program to your bootable disc. You may download it from our website. STEP 3. Copy the latest BIOS for your LEX motherboard from our website to your bootable disc.

  • Page 83: Appendix A:power Consumption Test

    Appendix A: Power Consumption Test Condition Item Spec Atom E3845 1.91 Ghz Memory DDR3L 1333 4GB Operating System Windows 7 / SP1 Test Program 3D Mark 06 HDD 2.5" SATA Slim Type HDD mSATA 32GB HDD 3.5" SATA Standard HDD Test Result for reference only ! Start up Operation...
  • Page 84 Condition ( with 4IP Camera ) Item Spec Atom E3845 1.91 Ghz Memory DDR3L 1333 4GB Operating System Windows 7 / SP1 Test Program 3D Mark 06 HDD 2.5" SATA Slim Type HDD mSATA 32GB HDD 3.5" SATA Standard HDD Camera IP Camera *4 pieces Test Result for reference only !

  • Page 85: Appendix B:resolution List

    Appendix B: Resolution list 640 x 480 x ( 256 / 16bit / 32bit ) 800 x 600 x ( 256 / 16bit / 32bit ) 1024 x 768 x ( 256 / 16bit / 32bit ) 1152 x 864 x ( 256 / 16bit / 32bit ) 1280 x 600 x ( 256 / 16bit / 32bit ) 1280 x 720 x ( 256 / 16bit / 32bit ) 1280 x 768 x ( 256 / 16bit / 32bit )

  • Page 86: Appendix C: F75111N I C Dio Decice

    Appendix C: F75111N I C DIO device 1-1 IO Device: F75111 under Windows The Sample code source you can download from Source fi le: F75111_DIOSrc.rar http://tprd.info/lexwiki/index.php/IO_Device:F75111 Binary fi le: F75111_DemoBin.rar USERNAME & PASSWORD: sf How to use this Demo Application 1.
  • Page 87 p.s. f75111 send "F75111_SetWDTEnable(BYTE byteTimer)" including a parameter "timer", if there's no disable signal (F75111_SetWDTDisable()) to stop it before timer countdown to 0, System will reboot. if there's disable signal received, resent Enable WDT signal, for a loop to prevent from reboot Introduction Initial Internal F75111 port address (0x9c) defi...
  • Page 88 Set output value void F75111::InterDigitalOutput(BYTE byteValue) BYTE byteData = 0; byteData = (byteData & 0x01 )? byteValue + 0x01 : byteValue; byteData = (byteData & 0x02 )? byteValue + 0x02 : byteValue; byteData = (byteData & 0x04 )? byteValue + 0x04 : byteValue; byteData = (byteData &...

  • Page 89: Io Device: F75111 Vb6 Under Windows

    Disable WatchDog void F75111_SetWDTDisable () WriteByte(F75111_INTERNAL_ADDR,WDT_CONFIGURATION,0x00); // Disable WatchDog 1-2 IO Device: F75111 VB6 under Windows The Sample code source you can download from Source fi le: 75111_VB_v10.rar http://tprd.info/lexwiki/index.php/IO_Device:F75111_VB6 Binary fi le: 75111_VB_Src.rar USERNAME & PASSWORD: sf How to use this Demo Application A Function - Enable WDT timer ,Key-in the value by seconds then system will reboot after value which you key-in in left text box !! B Function - Disable WDT timer ,Push down the button then WDT timer value will be clear !!
  • Page 90 SDK Function Introduction Function EnableWDT Function EnableWDT(timer As Integer) Call WriteI2CByte(&H3, &H3) Call WriteI2CByte(&H37, timer) Call WriteI2CByte(&H36, &H73) End Function Function DisableWDT Function DisableWDT() Call WriteI2CByte(&H36, &H0) End Function Function SetDOValue Function SetDOValue(dovalue As Integer) Call WriteI2CByte(&H23, &H0) Call WriteI2CByte(&H20, &HFF) Call WriteI2CByte(&H2B, &HFF) Call WriteI2CByte(&H21, dovalue) End Function...

  • Page 91: Io Device: F75111 Under Linux

    1-3 IO Device: F75111 under linux The Sample code source you can download from Source fi le: F75111v2.0L.tar.gz http://tprd.info/lexwiki/index.php/IO_Device:F75111_under_linux Binary fi le: F75111v2.0LBin.tar.gz USERNAME & PASSWORD: sf How to compile source code 1. Compile source code with Code::Blocks download and install the Code::Block with command "apt-get install codeblocks" Open an exist project(F75111.cbp) in Code::Blocks, click the compile button ( add an option 'pkg-confi...
  • Page 92 1. Press the "Start" button to test DIO function 2. Press the "Enable" button to test WDT function 3. Press the "Disable" button to disable WDT 4. Check the "Enable Loop" box and press "Enable" to do WDT loop test 5.
  • Page 93 Set output value void F75111::InterDigitalOutput(BYTE byteValue) BYTE byteData = 0; byteData = (byteData & 0x01 )? byteValue + 0x01 : byteValue; byteData = (byteData & 0x02 )? byteValue + 0x02 : byteValue; byteData = (byteData & 0x04 )? byteValue + 0x04 : byteValue; byteData = (byteData &...
  • Page 94 Enable WatchDog void F75111_SetWDTEnable (BYTE byteTimer) WriteByte(F75111_INTERNAL_ADDR,WDT_TIMER_RANGE ,byteTimer); // set WatchDog range and timer WriteByte(F75111_INTERNAL_ADDR,WDT_CONFIGURATION,WDT_TIMEOUT_FLAG | WDT_ENABLE | WDT_PULSE | WDT_PSWIDTH_100MS); // Enable WatchDog, Setting WatchDog confi gure Disable WatchDog void F75111_SetWDTDisable () WriteByte(F75111_INTERNAL_ADDR,WDT_CONFIGURATION,0x00); // Disable WatchDog...

  • Page 95: Appendix D: Cpc-Car Power Control (Option)

    Appendix D: CPC-Car Power Control (Option) Introduction: CPC is designed specifi cally for the car, with the over-current protection. Acceptable input 9V ~ 36V wide voltage input, and can prevent momentary surge caused by excessive input voltage causes damage to the motherboard parts protection mechanisms, and there are, input power protection device to prevent reverse the negative.
  • Page 96 Auto Mode Provides power: When Key is inserted into the ACC stalls, CPC default through (Delay Main Power On setting within) delay 20 seconds before providing power to the motherboard Boot-Up : CPC provides power to the motherboard, the power will be executed. The shutdown : When Key switch back to the OFF position, CPC default (set value of the OS Delay Off) at 5 minutes after the motherboard through the shutdown.
  • Page 97 Power saving mode: If you close more than 10 minutes, CPC will enter power-saving mode. Then the total current consumption <2mA, in order to protect the car battery. When the battery voltage is low : When the battery does not have enough electricity for 10 minutes, CPC will immediately turn off the power to the motherboard, To protect the battery.
  • Page 98 Battery Low Voltage Level setting: When the battery voltage is lower than the setting voltage, the system will defi ne it as "Under voltage". The below list with the options of battery levels user may choose depend on its 12V or 24V battery. Level 12V Battery 24V Battery...
  • Page 99 Car Power Control (CPC) application Introduction About CPC info on LEX WiKi: Users can download the CPC AP form LEX WiKi- CPC AP can set the delay time and start the "Under Voltage" protection. The CPC AP introduction from LEX WiKi: http://tprd.info/lexwiki/index.php/CPC_Utility_under_Windows...
  • Page 100 Setting Page: I C Address Default is "B6". Press the submit button when fi nish selecting I C address, then CPC Basic Setting section and CPC Monitor Setting section will be enable to set. 3. Delay Main Power On Set the delay time which CPC turn on the computer. There are 14 options for this delay time setting: 0sec, 5sec, 10sec, 15sec, 20sec, 30sec, 45sec, 1min, 3min, 5min,10min, 15min,30min, 45min.
  • Page 101 5. Main Power Delay Set delay time of cutting off the power output after computer is turned off. There are 17 options as OS delay off setting: 0sec, 5sec, 10sec, 15sec, 20sec, 30sec, 45sec, 1min, 3min, 5min, 10min, 15min, 30min, 45min, 1hour, 2hour and 3hour.
  • Page 102 Disable Battery Low Voltage Detect: This button is to close the battery low voltage protection function. The default setting is to click this item (Disable ULV) If select this option, you don't have to set other things in the battery setting window. Besides, Period Voltage and Battery Type are also be hidden in main window when starting to monitor.

Table of Contents