Summary of Contents for TechnoSpark Systems NMEA 2000 Wifi Replicator
- Page 1 NMEA2000 WIFI Replicator USER'S MANUAL TechnoSpark Systems | Revision 1.02 | 27 Feb. 2019...
- Page 2 Congratulations on the purchase of the NMEA 2000 WiFi Replicator! The NMEA 2000 WiFi Replicator lets you connect your PC’s, Mac’s, tablets, or smartphones to an NMEA 2000® network so you can monitor and control your vessel using the App or PC/Mac Software.
-
Page 3: Principle Of Operation
NMEA2000® interface. The network over which this service is offered is implemented as a TCP/IP (Transmission Control Protocol/Internet Protocol) network. Features The NMEA 2000 Wifi Replicator has the following features: NMEA2000® Interface WLAN Interface integrated Setup Wizard... -
Page 4: Application Scope
Figure 1: NMEA 2000 Wifi Replicator Application scope Hereafter, two variants of operation are listed for better understanding. Figure 2: Server/Router/Client Operation Mode. Replicator is connected to Wi-Fi Router This is the preferred use of the Replicator, due to not interfering with already existing WI-FI environments. -
Page 5: Installation
Figure 3: Server/Client Operation Mode. The Replicator acts as an Access Point for the clients and serves the N2K Data directly to the clients. In this case, the mobile or terminal devices do not detour but register at the Replicator and are provided with network data right away. -
Page 6: Quick Setup
1. Integration into NMEA2000® network The Replicator can be integrated into any desired location of a NMEA2000® backbone. Either a free port ( M12, 5Pin, female ) on the backbone, or an additional T-connector as an extension are then needed. It is equally possible to connect the Replicator at the end of a drop cable. - Page 7 Connect your smartphone, tablet or PC via network settings with the now visible access point “REPLICATOR-AP”. See Figure 4. The associated password can be found on the back of the device. Figure 4: WiFi-Settings on Smartphone Finish the setup by typing the IP-address of the Replicator ( 10.10.1.1 ) and the TCP port ( 1343 ) , if you already have an appropriate app or software on your device.
-
Page 8: Advanced Setup
Advanced Setup The advanced setup is interpreted for occasions, when the customer wants to change the current operation mode. The integrated setup wizard helps to carry out some adjustments easily. By pressing and holding the SETUP pin on the frontside of your Replicator for about 3-5 seconds you call up the setup wizard. - Page 9 Setup wizard - Device Settings 2.1. You may now choose how to operate the Replicator. It recommended to connect your Replicator with the router, if you have an already existing WiFi environment onboard. Therefore, you have to switch from access point mode to station mode.
- Page 10 The next step to face is the field < NMEA PROTOCOL >. Enter one of the values below at will. Please note that the app / software you are using to read out your NMEA network data, supports the appropriate protocol. Code 11 –...
- Page 11 Setup wizard – Device Info 2.2. In this area, the user gets all significant data and information about the module and the Wifi status. Setup wizard – Firmware Update 2.3. In this menu part, it is possible for the user to upload any updates which are provided by the manufacturer right into the Replicator.
-
Page 12: Technical Data
Technical Data Specifications Parameter Value Decription NMEA 2000 Connector Micro-C, male Industry Level Waterproof WLAN Transmit Mode 54Mb/s Wi-Fi 2.4 Ghz 802.11b/g/n EU / US Wi-Fi antenna range 30 / 100 m / feet Operating input Voltage 6 - 36V supply from NMEA 2000 Backbone Power Consumption <... - Page 13 Message PGN Name 126992 System Time 127237 Heading/Track control 127245 Rudder 127250 Vessel Heading 127251 Rate of Turn 127257 Attitude 127488 Einge Param Rapid Update 127489 dynamic Engine Parameter 127493 dynamic Transmission parameter 127501 Binary Switch Bank Status 127505 Fluid Level 127506 DC Detailed Status 127508...
- Page 14 129809 AIS Class B Static Data Report Part A 129810 AIS Class B Static Data Report Part B 130074 Route and WP Service 130306 Wind Data 130310 Environmental Parameter 130311 Environmental Parameter 130312 Temperature 130314 Actual Pressure 130576 Small Craft Status /Trim (**) in operation mode „11“...
-
Page 15: Important Notices
Technospark Systems will not be held responsible for any damage to the user that may result from accidents or any other reasons during operation of the user’s unit according to this document.
Need help?
Do you have a question about the NMEA 2000 Wifi Replicator and is the answer not in the manual?
Questions and answers