Stamina wirk Linea Owner's Manual

Standup workstation

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Owner's

Manual

Product May Vary Slightly From Pictured.

When calling for parts or

service, please specify

the following number :

This Product is Distributed Exclusively by

Model#: 85-4000

STAMINA PRODUCTS

MADE IN CHINA

2040 N. Alliance, Springfield, MO 65803

Customer Service

1 (800) 375-7520

2014, 11

www.staminaproducts.com

Table of Contents

Summary of Contents for Stamina wirk Linea

Page 1 When calling for parts or service, please specify the following number : This Product is Distributed Exclusively by Model#: 85-4000 STAMINA PRODUCTS MADE IN CHINA 2040 N. Alliance, Springfield, MO 65803 Customer Service © 2014 Stamina Products, Inc. 1 (800) 375-7520 2014, 11 www.staminaproducts.com...
Page 2: Table Of Contents
Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time. Friday, 8:00 A.M. - 3:00 P.M., Central Time. ONLINE TELEPHONE MAIL CUSTOMER SERVICE CUSTOMER SERVICE CUSTOMER SERVICE STAMINA PRODUCTS, INC. customerservice@staminaproducts.com Tel: 1 (800) 375-7520 Fax: (417) 889-8064 ATTN: Customer Service www.staminaproducts.com P.O. Box 1071 Springfield, MO. 65801-1071 TABLE OF CONTENTS Hardware Identification Chart ....
Page 3: Hardware Identification Chart
HARDWARE IDENTIFICATION CHART This chart is provided to help identify the fasteners used in the assembly process. Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws.
Page 4: Assembly Instructions
ASSEMBLY INSTRUCTIONS Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed.
Page 5 ASSEMBLY INSTRUCTIONS STEP 2 Slide the TABLE SLIDER(6) onto the TABLE POST(3). Insert the CARRIAGE BOLT(M8x1.25x50mm) (41) through the square hole on the TABLE POST(3) and the slot on the TABLE SLIDER(6). STEP 3 Attach the SIDE TABLE SUPPORT(7) to the TABLE POST(3) by sliding the SIDE TABLE SUPPORT(7) onto the CARRIAGE BOLT(M8x1.25x50mm)(41), then insert the bolts which are welded on the SIDE TABLE SUPPORT(7) through the holes on the TABLE POST(3) and secure with WASHERS(M8)(44) and NYLOCK NUTS(M8x1.25)(45).
Page 6 ASSEMBLY INSTRUCTIONS STEP 5 Refer illustrations A, B, and C. Place the BACK SUPPORT(9) into the TABLE SLIDER(6) and turn it as shown in the below illustrations to install the BACK SUPPORT(9) into position. STEP 6 Attach the SEAT SUPPORT(5) to the SEAT SLIDER(4) with BUTTON HEAD BOLT(M8x1.25x60mm)(34), WASHER(M8)(44), and NYLOCK NUT(M8x1.25)(45).
Page 7 ASSEMBLY INSTRUCTIONS STEP 8 Refer to the illustration below. Attach the MOUNTING BRACKETS(10) and TALL MOUNTING BRACKETS(11) to the bottom side of the TABLE(15) with BUTTON HEAD BOLTS(M6x1x15mm)(40). BOTTOM VIEW...
Page 8 ASSEMBLY INSTRUCTIONS STEP 9 Refer to the Bottom View below. Attach the TABLE(15) to the unit by attaching the TALL MOUNTING BRACKETS(11) to the TABLE SLIDER(6) and attaching the MOUNTING BRACKETS(10) to the BACK SUPPORT(9) with BUTTON HEAD BOLTS(M8x1.25x110mm)(33), WASHERS(M8)(44), and NYLOCK NUTS(M8x1.25)(45).
Page 9: Operational Instructions
OPERATIONAL INSTRUCTIONS SEAT ADJUSTMENT 1. The SEAT(18) can be set to a 30 degree angle from horizontal. Set the SEAT(18) with the desired angle and lock in position with the PULL PIN(29). 2. There are four adjustment holes on the UPRIGHT(2) for adjusting the SEAT(18) to different heights.
Page 10: Storage
3. Worn or damaged components shall be replaced immediately or the Wirk Linea Standup Workstation removed from service until repair is made. 4. Only Stamina Products supplied components shall be used to maintain/repair the Wirk Linea Standup Workstation. 5. Keep your Wirk Linea Standup Workstation clean by wiping it off with an absorbent cloth after use.
Page 11: Warranty
To implement this limited warranty, send a written notice stating your name, date, and place of purchase and a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071, Springfield Missouri, USA, 65801-1071, or email us at customerservice@staminaproducts.com, or call us at 1-800-375-7520.
Page 12: Product Parts Drawing
PRODUCT PARTS DRAWING FRONT BACK...
Page 13: Parts List
PARTS LIST PART# PART NAME Base Frame Upright Table Post Seat Slider Seat Support Table Slider Side Table Support Side Table Post Back Support Mounting Bracket Tall Mounting Bracket Lever Quick Release Gas Shock Table Base Board Side Table Seat Pencil Tray Square Plug (20mm x 20mm) Feet...
Page 15: Fax/Mail Ordering Form
ATTN: Customer Service www.staminaproducts.com P.O. Box 1071 Springfield, MO. 65801-1071 Would you like to recieve email information or special offers from Stamina Products? Register at contact staminaproducts.com. TO ORDER PARTS TO ORDER PARTS If there are missing or damaged parts, you can go to parts.staminaproducts.com and order those parts. If you have questions, please contact customer service.