Advertisement
Quick Links
MERCURY – TILLER ONLY 15 & 20HP
TrollMaster is a precision throttle control designed to achieve the maximum in trolling speed
accuracy. The memory feature included in this control will allow returning to the best fishing
speed time and time again. Whether you are pulling your bait or back trolling, TrollMaster is
the answer to your speed control needs. Spend your time trolling, not going to the motor to
adjust the speed.
CALL: 866-228-7655
EMAIL: info@marinetechproducts.com
NEW
A DDRESS
A S
O F
M ARCH
1
MAIL: -
MARINETECH PRODUCTS, INC.
TROLLMASTER
1360 EAST COUNTY ROAD E
VADNAIS HEIGHTS, MN 55110
PHONE: 651-486-2010
FAX: 651-486-6989
2008-2009
,
2 013
ST
Advertisement
Summary of Contents for MarineTech TrollMaster Series
- Page 1 CALL: 866-228-7655 EMAIL: info@marinetechproducts.com NEW A DDRESS A S O F M ARCH 1 , 2 013 MAIL: - MARINETECH PRODUCTS, INC. TROLLMASTER 1360 EAST COUNTY ROAD E VADNAIS HEIGHTS, MN 55110 PHONE: 651-486-2010...
- Page 2 See; Set The Servo Arm for further instruction on how to install your servo motor properly. Replacement servo motors are available for the Hitec HS322HD (shown above) and the SG-5010 (not shown) To purchase call MarineTech Products, Inc. PH: 866-228-7655...
- Page 3 1. Place a towel under the throttle mechanism to prevent dropped parts from being lost. 2. Remove top intake bolt.
- Page 4 3. Place the bolt provided with your kit, through the servo bracket and place the spacers on the bolt behind the bracket. 4. Mount the servo in the top intake bolt hole. Make sure the front of the bracket is in contact with the manifold.
- Page 5 5. Loosen the set screw at the brass piece on the carburetor and remove the throttle rod. 6. Place the loop in the TrollMaster cable over the brass fitting and replace the Mercury Throttle Rod.
- Page 6 7. Adjust the loop in the Mercury throttle rod as shown. 9. Place the servo arm with the brass piece aligned to 6 o’clock. Loosen the set screw at the brass connector on the servo arm. Pull the cable to remove the slack and secure the...
- Page 7 CAUTION: Make sure the throttle remains closed. Pull the cable tight to remove slack. Then place the swedge provided over the cable behind the brass connector and crimp in place. 10. Make a small slit in the rubber plug for the control cable connector to pass through.
-
Page 8: Testing The Controller
Connecting to a power source: It is recommended that you install a two-amp fuse on the positive power lead of the PRO and PRO2 models before connecting to a power source. Connect the two amp fused Red wire to +12 volts DC and the Black wire to -12 volts DC. -
Page 9: Troubleshooting
TrollMaster unit to its fullest potential. If the battery is fully charged and the unit is still not operating properly contact MarineTech Products, Inc. 866-228-7655 to have the unit inspected at our facility. If you need assistance with Troubleshooting contact MarineTech... -
Page 10: To Order Replacement Parts
If you would like to order any of the above mentioned replacement parts check with your local retailer, if they do not have the item in stock they can order it for you or you can order directly from MarineTech Products, Inc. For pricing and availability call MarineTech Products, Inc. 866-228-7655... -
Page 11: Service And Warranty
MarineTech P roducts, I nc. w arrants t his p roduct t o b e f ree o f d efects i n m aterial a nd ...
Need help?
Do you have a question about the TrollMaster Series and is the answer not in the manual?
Questions and answers