Table of Contents
Advertisement
Quick Links
WPS600
Hydraulic Pressure Transducer
User's Guide
This accessory complies with the following standards:
Electromagnetic Compatibility (EMC) Directive 2004/108/EC
FCC Part 15
Pressure Equipment Directive 97/23/EC Article 3.3
600 bar
60 MPa
8700 psi
Saelig Company, Inc. 71 Perinton Parkway, Fairport, NY 14450 USA 1-585-385-1750
info@saelig.com
www.saelig.com
DO187-4
Advertisement
Table of Contents
Related Manuals for PICO WPS600
Summary of Contents for PICO WPS600
- Page 1 WPS600 Hydraulic Pressure Transducer User’s Guide This accessory complies with the following standards: Electromagnetic Compatibility (EMC) Directive 2004/108/EC FCC Part 15 Pressure Equipment Directive 97/23/EC Article 3.3 600 bar 60 MPa 8700 psi Saelig Company, Inc. 71 Perinton Parkway, Fairport, NY 14450 USA 1-585-385-1750 info@saelig.com...
- Page 2 Pico Technology WPS600 User’s Guide 1. Safety Symbols appearing in this manual: WARNING statements identify conditions or practices that could result in injury or death. WARNING CAUTION statements identify conditions or practices that could result in damage to this product or other property.
- Page 3 Use only pressure hoses that have been pressure-tested. Do not use them if they have been disassembled, modified or damaged. DO NOT use in long-term or permanent installations The WPS600 is intended for immediate diagnostic purposes only. It should not, for example, be connected to a vehicle as a monitoring system. DO187-4...
- Page 4 600 bar / 60 MPa / 8700 psi 60 bar / 6 MPa / 870 psi Compatible fluid types The WPS600 is designed for use with hydraulic fluids. Do not use with any other type of liquid or gas. DO187-4...
- Page 5 WPS600 User’s Guide Pico Technology 3. The parts of your WPS600 pressure transducer Signal output to oscilloscope Front-panel controls USB charging port Inlet port Signal output Use the BNC-to-BNC cable supplied to connect this to your oscilloscope. This connector is made of plastic to ensure electrical safety.
-
Page 6: Front Panel Controls
Pico Technology WPS600 User’s Guide 4. Front-panel controls Power button Press once to switch on. Press once again to switch off. Keep the unit switched off when not in use to Charging indicator conserve battery Lights up when power. battery is charging. -
Page 7: Preparation For Use
Charge the internal battery. For instructions, see Section 7: “Maintenance”. Zeroing the transducer The WPS600 has a zeroing function to ensure its long-term accuracy. The transducer should be zeroed before first use, and can be zeroed again if the unit starts to show an error in the zero-pressure reading. - Page 8 Connect the transducer to the hydraulic system, either directly or through a suitable high-pressure hose. Use ONLY pressure hoses specifically designed for high-pressure testing. Pico Technology cannot accept responsibility for damage or injury caused by the use of unsuitable pressure hoses or adaptors. WARNING Bleed any air out of the measurement chamber.
-
Page 9: Maintenance
Unplug the USB cable from the transducer before use. Leaving the cable plugged in may affect measurement accuracy. The battery inside the WPS600 is designed to give a long service life and is not user-replaceable. Repairs If the unit is damaged or stops working, or the battery is not charging or holding charge, return it to Pico Technology or an authorized Pico distributor for repair. -
Page 10: Specifications
The SI unit of pressure and vacuum is the pascal, symbol Pa. This is related to psi (pounds per square inch) and bar as follows: 1 bar = 100,000 Pa 1 psi = 6,894.757 Pa 10. Technical support For assistance with operating this device, please contact Pico Technology at www.picotech.com. DO187-4... - Page 11 Manufactured in the United States Copyright © 2011–2014 Pico Technology Ltd. Pico Technology is a registered trademark of Pico Technology Ltd. www.picotech.com Saelig Company, Inc. 71 Perinton Parkway, Fairport, NY 14450 USA 1-585-385-1750 DO187-4 info@saelig.com...
Need help?
Do you have a question about the WPS600 and is the answer not in the manual?
Questions and answers