1. Manuals
  2. Brands
  3. ADB Stagelight Manuals
  4. Light Fixture
  5. OKSALIS Series
  6. Instruction manual

ADB Stagelight OKSALIS Series Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

EN
OKSALIS
INSTRUCTION MANUAL
OKSALIS FL10 (AL2010)
OKSALIS FL20 (AL2020)
Congratulations on choosing an ADB product! We thank you for your custom.
Please note that this xture - like all the others in the wide ADB range - has been designed and made with total
quality assurance to ensure excellent performance and best meet your expectations and requirements.
www.adbstagelight.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OKSALIS Series and is the answer not in the manual?

Questions and answers

Summary of Contents for ADB Stagelight OKSALIS Series

  • Page 1 OKSALIS INSTRUCTION MANUAL OKSALIS FL10 (AL2010) OKSALIS FL20 (AL2020) Congratulations on choosing an ADB product! We thank you for your custom. Please note that this xture - like all the others in the wide ADB range - has been designed and made with total quality assurance to ensure excellent performance and best meet your expectations and requirements.

  • Page 2: Table Of Contents

    INDEX SAFETY INFORMATION UNPACKING AND PREPARATION INSTALLATION AND START-UP Installing the fixture Connecting to main supply Connecting the control signal line: DMX / Art-Net Switching on the fixture and basic SetUp MENU SETTING DMX CHANNEL FUNCTIONS MAINTENANCE Warning / Caution Periodical cleaning Battery removal Opening the covers...

  • Page 3: Safety Information

    1. SAFETY INFORMATION SAFETY INFORMATION IMPORTANT: ADB Stagelight recommends you carefully read and keep the safety information on this product, also available in digital format at the following link: www.adbstagelight.com Ref: [FIS00X - Safety Information Oksalis series] INFORMAZIONI DI SICUREZZA...

  • Page 4: Unpacking And Preparation

    2. UNPACKING AND PREPARATION 2 x 183102/805 Packing contents - Fig. 1 Head tilt adjustment - Fig. 2 OKS LIS...

  • Page 5: Installation And Start-Up

    3. INSTALLATION AND START-UP Installing the fixture Installing the projector - Fig. 3 The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.

  • Page 6: Connecting The Control Signal Line: Dmx / Art-Net

    Mains Connecting to the mains supply - Fig. 5 Connecting the control signal line: DMX / Art-Net DMX 512 5 PIN SCREEN SIGNAL SIGNAL DMX 512 3 PIN SIGNAL SCREEN SIGNAL Connecting to the control signal line DMX) - Fig. 6 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity.

  • Page 7: Dmx Channel Functions

    Reversal of the display - Fig. 8 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512).

  • Page 8: Maintenance

    6. MAINTENANCE Warning / Caution • To avoid damage to the internal parts of the fixture when the fixture is not working, is recommended to turn the head down before turning the fixture off, so that the front lenses of the fixture are invested as little as possible from the sun. •...

  • Page 9: Battery Removal

    Battery removal Battery removal - Fig. 10 This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. OKS LIS...

  • Page 10: Opening The Covers

    Opening the covers Opening the covers - Fig. 11 OKS LIS...
  • Page 11 Cleaning of the filters / grids - Fig. 12 OKS LIS...

  • Page 12: Cause And Solution Of Problems

    7. CAUSE AND SOLUTION OF PROBLEMS THE PROJECTOR WILL NOT SWITCH ON ELECTRONICS NON-OPERATIONAL PROBLEMS DEFECTIVE PROJECTION REDUCED LUMINOSITY POSSIBLE CAUSES CHECKS AND REMEDIES No mains supply. Check the power supply voltage. LED exhausted or defective. Call an authorised technician. Signal transmission cable faulty or disconnected.
  • Page 13 8. DATASHEET POWER SUPPLIES BODY OKSALIS FL 10 100/240V 50/60 Hz Structure in aluminium with die-cast plastic cover Optional frame for external gels and frost filters INPUT POWER Optional top hat (adjustable with the Zoom 300VA movement) (10.55") Zoom OUT MAINS OUT ELECTRONICS Max 5 units...
  • Page 14 OKSALIS FL 20 (10.55") Zoom OUT (15.55") (9.84") Zoom IN (17.20") (18.62") (12.60") (20.47") (11.81") POWER SUPPLIES - CMY mode The projectors works in the same way Electronic check-up of every single parameter with 100/240V 50/60 Hz as a classical CMY fixture error alarm Halo Emulation 750W, 1000W, 1200W, 2000W, DMX level monitoring on each channel...

This manual is also suitable for:

Oksalis fl20Oksalis fl10

Table of Contents