PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the CAUTION instructions below when servicing. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous WARNING! radiation exposure.
Page 3
How to Adjust the Rotating Phase of the Gear, Main Cam 1) Push down the hooking catch of the CHAS. MECH, and remove the TRAY. 2) Align the arrow mark of the Gear, Main Cam with the black round mark of the CHAS, MECHA as shown below. 3) Confirm that the Slide, Mech Cam is located in the right position, then insert the TRAY gently.
TEST MODE 1. How to Activate CD Test Mode 2. How to Cancel CD Test Mode Insert the AC plug while pressing the function CD button. Either one of the following operations will cancel the CD test All FL display tubes will light up, and the test mode will be mode.
Page 12
IC DESCRIPTION IC, LC78622NE Pin No. Pin Name Description DEFI Defect sense signal (DEF) input pin. (Connect to 0V when not used). Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Phase comparator output pin to control external VCO. VVSS —...
Page 13
Pin No. Pin Name Description XVDD — Crystal oscillator power supply pin. XOUT Pin to which external 16.9344 MHz crystal oscillator is connected. XVSS — Crystal oscillator GND pin. Be sure to connect to 0V. SBSY Subcode block sync signal output pin. EFLG C1, C2, single and dual correction monitoring pin.
Page 14
IC, LA9241ML Pin No. Pin Name Description Pin to which external pickup photo diode is connected. RF signal is created by adding FIN2 with the FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal. FIN1 Pin to which external pickup photo diode is connected.
Page 15
Pin No. Pin Name Description Pin from which TES signal is output to DSP. “High Frequency Level” is used to judge whether the main beam position is on top of bit or on top of mirror. SLOF Sled servo off control input pin. 39, 40 CV–, CV+ CLV error signal input pin from DSP.
MECHANICAL PARTS LIST 1/1 REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION 1 84-ZG1-225-010 BELT,SQ1.0-63.3 21 83-ZG3-604-010 RING,MAG 2 2 84-ZG1-672-010 F-CABLE,5P 1.25 210MM WHITE N 22 83-ZG3-213-010 LVR,SW 3 87-045-364-010 MOTOR(BCH3B14) 23 84-ZG1-208-210 LEVER,CAM 4 84-ZG1-267-010 PULLEY,LOAD MO 8 <ZA4RDC,ZA4RNDC,ZA3RDF,ZA3RNDF,ZA8RDC>...
Page 18
CD MECHANISM EXPLODED VIEW 1/1 (3ZG-2E3) P.C.B CD MECHANISM PARTS LIST 1/1 (3ZG-2E3) REF. NO PART NO. KANRI DESCRIPTION 1 83-ZG2-243-310 CHAS ASSY,SHT 2 83-ZG2-235-010 GEAR,A3 3 83-ZG2-205-210 GEAR,B 4 83-ZG2-236-010 GEAR,MOTOR 3 5 83-ZG2-253-110 SHAFT,SLIDE 5 6 87-A90-836-010 PICKUP,KSS-213F 7 83-ZG2-227-310 TURN TABLE,C1 8 83-ZG2-245-510...
CD MECHANISM EXPLODED VIEW 1/1 (KSM-2131 FAM) COVER SPINDLE MOTOR MOTOR C.B CD MECHANISM PARTS LIST 1/1 (KSM-2131 FAM) REF. NO PART NO. KANRI DESCRIPTION 1 9X-264-629-220 MOTOR CHASSIS ASSY(MB)(FR) 2 92-626-907-010 GEAR(A)(S) 3 87-A90-836-010 OPTICAL PICK UP KSS-213F 4 92-626-908-020 SHAFT SLED 5 92-627-003-010 GEAR(B)
Page 20
CD MECHANISM EXPLODED VIEW 1/1 (KSM-880CAB) P.C.B CD MECHANISM PARTS LIST 1/1 (KSM-880CAB) REF. NO PART NO. KANRI DESCRIPTION 1 91-564-722-110 CONN,PIN 6P 2 91-572-085-110 LEAF SWITCH 3 9X-264-655-010 SL MOTORR ASSY 4 M8-ZZK-C90-070 KSM-880CAB 5 92-647-416-020 SPRING EXTENSION 6 92-647-595-020 SHUTTER B 7 92-647-732-010 NS SLIDE RACK...