Advertisement
Thank you for choosing a Zerica® water dispenser.
Using the appliance is simple, however for best results, it is important to read the following instructions.
INTRODUCTION
This manual is the documentation and an integral part of the appliance and must accompany the product even if it is
transferred or sold after first installation.
Its disclosure to all interested parties is a prerequisite for correct operation and protection from possible accidents
and damage to the appliance and injury to third parties.
These instructions are intended to provide information regarding correct installation and operation.
The presence of such warnings does not imply that the manufacturer assumes any liability for any damage to property
or injury to third parties caused by the use of the device, which has all the original certifications required in order to
make it suitable for the use for which it has been designed, as well as safe in compliance with applicable standards.
The reproduction of the contents of this manual for distribution to third parties is strictly forbidden without the
express prior consent of the manufacturer Zerica S.r.l.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning
the use of the appliance by a person responsible for their safety. Children must be supervised to assure that they do
not play with the machine.
The appliance must not be installed near water jets.
The appliance needs to be installed on a flat surface.
The appliance must not be cleaned with water jets.
The appliance is compliant with the N climate class and must be installed in locations with a temperature between
+16°C and +32°C. Take all necessary precautions and do not install in locations with temperatures lower than +3°C
because if the water inside the product freezes, it seriously damages the water circuit.
This appliance generates a sound pressure level below 70dB.
REFRESH® P HPDC – REFRESH® P TC
REFRESH® Pensile
Installation and Operation Manual
(010)
(020)
Advertisement
Table of Contents
Related Manuals for Zerica REFRESH P HPDC
Summary of Contents for Zerica REFRESH P HPDC
- Page 1 REFRESH® P HPDC – REFRESH® P TC REFRESH® Pensile Installation and Operation Manual Thank you for choosing a Zerica® water dispenser. Using the appliance is simple, however for best results, it is important to read the following instructions. (010) INTRODUCTION This manual is the documentation and an integral part of the appliance and must accompany the product even if it is transferred or sold after first installation.
- Page 2 UNPACKING Place the appliance in the upright position which can be easily identified by reading the direction mark “UP” on the box. Open the package and check that there are no dents or obvious damages to the appliance caused by transportation. Any defects must be notified within 24 hours from delivery.
-
Page 3: Water Connection
WATER CONNECTION The system must be connected to the potable water supply network. If the system includes a filtration system, ensure that all the filter elements are properly installed before making any connection to the water supply. Refer to the appropriate paragraph or instructions supplied with the filters for installation, maintenance and expiry. - Page 4 R/C* (column tap) Screw “with care” the tube to the inferior part of the tap “without moving the black lever from place”...
-
Page 5: Electrical Connection
R/Z* (faucet spout) If the inlet water pressure is different than the one set at the factory, it is possible to regulate the spout and modify the height of the jet. Regulator underneath the button: unscrew the nut (G), take the button off (P) and adjust the screw slowly (V) Lateral regulator: adjust the screw slowly (V). -
Page 6: Temperature Regulation
TEMPERATURE REGULATION The exclusive HPDC® cooling system (optional), allows to get cold water in just 5 minutes from power on. The value set by the factory is 8°C, but it is possible to modify the temperature of the water adjusting the thermostat positioned behind the frontal panel of the machine (RFP240-260) or on the back of the product (RFP 080). -
Page 7: Maintenance Chart
MAINTENANCE CHART Date of installation Customer Address Tel. Installation company Model SERIAL NO. RESPECT MAINTENANCE DATES DURING WARRANTY (see warranty clauses) Date Litres Replaced parts Service centre (200) -
Page 8: Warranty
The warranty excludes those products that (I) in the opinion of ZERICA® have been damaged accidentally or during transportation if not notified to ZERICA Srl® directly within 8 days from the date of purchase, or due to incorrect or improper use or inappropriate or incorrect application, or following intervention or verifications or modifications carried out by anyone other than a ZERICA®... -
Page 10: Ec Declaration Of Conformity
In addition, the models of carbonators used by Zerica have a product PSxV below the limit established by the PED, at 50, and do not therefore have to be CE-marked as they come under the equipment referred to in art. 3§3 in said directive. - Page 11 Zerica has also requested verification of conformity assessment pursuant to the Italian Decree of 6 April 2004 no. 174 in appliance to REGULATION (EEC) N. 1935/2004 - “materials that come into contact with the water destined for human consumption” for the following components: ...
- Page 13 ZERICA srl Zona Industriale 90018 Termini Imerese (Pa) - Italy Tel. +39.091.8140341 – 091.8140377 – 091.8167962 – 091.9293333 Fax +39.091.8140364 http://www.zerica.com e-mail:info@zerica.com Total or partial reproduction is forbidden. The manufacturer disclaims any responsibility for any typographical errors included in this manual. It reserves the right to make amendments to own products considered necessary or useful withou jeopardising their functional features, without prior notice.