1. Manuals
  2. Brands
  3. Kozy-World Manuals
  4. Fireplace Accessories
  5. 20-6031
  6. Manual

Kozy-World 20-6031 Manual

Blower accessory
Hide thumbs

Advertisement

Table of Contents

Kozy-World
PACKAGE CONTENTS
Before beginnig assembly of product, make sure all parts are present. Compare
parts with package contents list and diagram under. If any part is missing or
damaged, do not attempt to assemble, install or operate the product. Contact
customer service for replacement parts.
Estimated Assembly Time: 30 minutes.
Tool List For Assembly (Not Included):
KEY NO
1
2
Part List
KEY NO
1
2
3
4
5
6
7
8
IMPORTANT: Read all instructions and warnings carefully before starting installation.
Failure to follow these instructions may result in a possible electric shock, fire hazard
and will void the warranty.
Questions about installation, operation, or troubleshooting? Before returning to your retailer, call
KOZY WORLD PHONE NUMBER (814)643-1775.
®
DESCRIPTION
PHILLIPS SCREWDRIVER
WIRE CUTTING PLIERS
PART NUMBER
XB001-01
XB002-01F
XB003-01
XB004-01F
PF06-0400-A
M4.2×8
4.0×8
VL057-03
BLOWER ACCESSORY
MODEL NO. 20-6031
DESCRIPTION
Power Cord
Blower
Temperature Sensor
Connect Wire
Rocker Switch
Screw
Screw
Cable Tie
QUANTITY
1
1
QUANTITY
1
1
1
1
1
6
1
6

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 20-6031 and is the answer not in the manual?

Questions and answers

Summary of Contents for Kozy-World 20-6031

  • Page 1 Kozy-World BLOWER ACCESSORY ® MODEL NO. 20-6031 PACKAGE CONTENTS Before beginnig assembly of product, make sure all parts are present. Compare parts with package contents list and diagram under. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts.

  • Page 2: Safety Information

    Safety Information 1. Read all instructions before using this appliance. 2. If possible always unplug this appliance when not in use. 3. Do not operate any heater with a damaged cord or plug or after the appliance malfunctions, has been dropped or damaged in any manner. 4.
  • Page 3 Exploded Drawing...
  • Page 4 Assembly Procedure for Item GFD2916 & GFD2922 & GFDC3030 Optional Parts: NOTICE: Shut off gas heater during the following blower installation. Figure 1 Remove upper Figure 2 Unscrew two Figure 3 Fix temperature fire box by unscrewing left screws on heat insulation sensor to heat insulation /right screws on the fire board cover and draw it out.
  • Page 5 Figure 10 Fix the grounding. Figure 11 Insert the blower. Connect the port Figure 12 and shell board with linker (male port) into the three wires preset aside screws (please refer to linker (female port) preset (red, yellow and black) with grounding label);...
  • Page 6 Assembly Procedure for Item FBD3211R Optional Parts: NOTICE: Shut off gas heater during the following blower installation. Figure 1 Remove upper Figure 2 Unscrew two Figure 3 Fix temperature fire box by unscrewing left screws on heat insulation sensor to heat insulation /right screws on the fire board cover and draw it out.
  • Page 7 Figure 11 Fix the grounding. Figure 12 Insert the blower. Figure 10 Fix the wires, which is matched with metal wafer, to the shell with three screws. Connect the port Figure 13 Figure 14 Push the rocker Figure 15 Insert the male and shell board with linker switch into the hole on the port, which is on the black...

  • Page 8: Electrical Connection

    Electrical Connection A 15 amp, 120 Volt, 60 Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation.

  • Page 9: Electrical Wiring Diagram

    Operating Instructions Using Rocker Switch, turn blower on and check for operation. Turn on Rocker Switch to the desired position. In the MAN position it will remain constantly on. AUTO position will be controlled by the Temperature Sensor. To stop the operation turn Rocker Switch to the OFF position.
  • Page 10 Maintenance of Motors Always disconnect the appliance from the main power supply and allow it to cool before any servicing operation. The motors used on the fan heater and flame blower are pre-lubricated for extended bearing life and require no further lubrication. However, periodic cleaning/vacuuming of the appliance around the air intake and exhaust, as well as the fan heater is recommended.

Table of Contents