Michel's R200 Manual

Michel's R200 Manual

Integrated wireless technology
Table of Contents

Advertisement

Integrated Wireless Technology
R200
Hardware – 0.7.0 / Firmware – 1.1.15

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the R200 and is the answer not in the manual?

Questions and answers

Summary of Contents for Michel's R200

  • Page 1 Integrated Wireless Technology R200 Hardware – 0.7.0 / Firmware – 1.1.15...
  • Page 2: Table Of Contents

    15-March-2018 Contents 1.0.0 Basic Information and Handling ......................4 1.0.1 Remote Certification ........................5 1.1.0 Charging/Battery Indicator ......................6 2.0.0 Home Screen ............................6 3.0.0 Setup Menu ............................6 3.1.0 Adding Units to the Remote ......................7 3.1.1 How to add an EZ Opener ......................7 3.1.1.1 How to add an EZ Opener and ‘ConveyHawk’...
  • Page 3 15-March-2018 5.0.0 Chute Opener Menu .......................... 18 5.1.0 Operating an EZ Opener Chute Opener ..................19 5.2.0 EZ Opener Chute Opener Edit Menu ..................... 19 5.2.1 Setting the Limits of the EZ Opener Chute Opener ..............19 5.2.1.1 Resolving Improper Positon of Chute on Installation ............. 20 5.2.2 Changing the Unit Name ......................
  • Page 4 15-March-2018 7.3.0 Controlling Multiple Light Units at the Same Time ................ 33 7.4.0 Controlling Multiple Light Units Manually from the T210 Remote Box ........34 7.5.0 Operating the Swing Auger ......................35 7.6.0 Swing Auger Edit Menu ........................35 7.6.1 Removing a Swing Auger Receiver ..................... 35 7.6.2 Reversing Motor Direction ......................
  • Page 5: Basic Information And Handling

    15-March-2018 1.0.0 Basic Information and Handling R200 Layout Overview 1. Power Button – Press to turn power on, Press and hold for 3 seconds to turn power off 2. Enter Button – Used to select a highlighted option on the screen 3.
  • Page 6: Remote Certification

    15-March-2018 For optimal remote performance and range, it is recommended you grip the remote as shown and hold it at least one foot away from your body to allow the wireless signal to properly disperse from the remote. 1.0.1 Remote Certification The enclosed device complies with Part 15 of the FCC Rules.
  • Page 7: Charging/Battery Indicator

    15-March-2018 1.1.0 Charging/Battery Indicator TARPS The battery indicator is present on every screen except when ‘Tarps’ is highlighted on CHUTES the Home screen. It will show a full, half or empty battery. AUGERS AUXILIARY The typical life expectancy of the battery is 10 hours of continued use. When the SETUP battery icon starts to flash red there are approximately 10 minutes of on time before the remote battery will die.
  • Page 8: Adding Units To The Remote

    15-March-2018 3. Changing the network ID allows multiple remotes to be added to the same network. In order for a Tarp, Chute Opener or Auger receiver to talk to multiple remotes the network ID must be the same. When the remotes are assembled the network ID’s are different. Even if the remotes have the same Network ID, they still have to be taught to the each receiver for them to work.
  • Page 9: How To Add An Ez Opener And 'Conveyhawk' Conveyor Combination System

    Section 5.2.1. The procedure to add the EZ Opener and ‘ConveyHawk’ Conveyor Combination System to the R200 remote is similar to that of a standalone EZ Opener; see Section 3.1.1.
  • Page 10: How To Add A T200 Or T210 Tarp Receiver System

    15-March-2018 3.1.2 How to add a T200 or T210 Tarp Receiver System 3.1.2.1 How to add a T200 Tarp Receiver Enter into the Setup Menu from the Home Screen. Use the up and down arrows to move the cursor to select / highlight Setup and then press Enter.
  • Page 11: How To Add A T210 Tarp Receiver

    15-March-2018 3.1.2.2 How to add a T210 Tarp Receiver Enter into the Setup Menu from the Home Screen. Use the up and down arrows to move the cursor to select/highlight Setup and then press Enter. Upon entering the Setup menu, ADD UNIT should be highlighted. Go to the T210 Tarp Receiver Box.
  • Page 12: How To Add A200 And A210 Auger Or Conveyor Receiver Systems

    15-March-2018 3.1.3 How to add A200 and A210 Auger or Conveyor Receiver Systems 3.1.3.1 How to add an A200 Auger Receiver Enter into the Setup Menu from the Home Screen. Use the up and down arrows to SETUP 1 move the cursor to select / highlight Setup and then press Enter. AUGER ADDED ADD UNIT 15 MIN SHUTDOWN...
  • Page 13: How To Add A Mic210 Side Chute System

    The MIC210 Side Chute Control Box will need to have settings adjusted after it has been paired to the R200 Remote for it to appear properly in the remote. Press the ‘Chute’ button on the R200 Remote. Then scroll down to ‘EDIT UNIT’...
  • Page 14: Changing The Shutdown Time Of The Remote

    15-March-2018 3.2.0 Changing the Shutdown Time of the Remote Enter into the Setup Menu from the Home Screen. Use the up and down SETUP 1 arrows to move the cursor to select / highlight Setup and then press Enter. ADD UNIT 15 MIN SHUTDOWN CHANGE NETWORK ID Use the down arrow and move the cursor over the ‘5 MIN SHUTDOWN’...
  • Page 15: Accessing The Groups Sub-Menu

    15-March-2018 3.4.2 Accessing the Groups Sub-Menu After all of the units are paired with the remote. The ‘GROUPS’ sub-menu can be SETUP 1 TARPS accessed by highlighting ‘SETUP’ on the ADD UNIT CHUTES 15 MIN SHUTDOWN home screen and pressing ‘ENTER’. This will CHANGE NETWORK ID AUGERS 68B0...
  • Page 16: Selecting A Group

    15-March-2018 3.4.4 Selecting a Group Highlight ‘GROUP TO EDIT:’ and press ‘ENTER’. This will scroll through all of the different groups on the GROUPS TARPS remote. If any group remains unnamed it is GROUP TO EDIT: CHUTES 0 TRAILER 1 recommended to give that group a unique MAKE CURRENT AUGERS...
  • Page 17: Tarp Menu

    15-March-2018 4.0.0 Tarp Menu To enter into the Tarp Menu, simply press the ‘Tarp’ function button on the side of the remote or select ‘TARPS’ from the Home Screen. TARPS If there is no tarp receivers paired to the remote, it will not allow access into the Tarp CHUTES Menu.
  • Page 18: Tarp Edit Menu

    15-March-2018 4.2.0 Tarp Edit Menu TARP 1 To get into the ‘Tarp Edit Unit’ Menu, enter into the Tarp Menu by using the ‘TARP’ 00 40 B2 C2 78 MOTOR OFF function button on the side of the remote or selecting ‘TARPS’ from the Home Screen. HOME Use the up or down arrow to select / highlight ‘Edit Unit’...
  • Page 19: Locating The Hardware And Firmware Version

    15-March-2018 blank space. Once the correct character has been set, press the down arrow to advance to the next character. EDIT TARP REMOVE UNIT CLOSE <=> OPEN When finished, press ‘Enter’ to save the changes. ADD REMOVE A CHILD EDIT UNIT NAME H:0.8.3 F:0.8.2 Press ‘Exit’...
  • Page 20: Operating An Ez Opener Chute Opener

    15-March-2018 5.1.0 Operating an EZ Opener Chute Opener The limits need to be set on the remote the first time it is used. It may let the chute opener move but damage to the chute opener and/or the trailer may occur if the limits are not properly set. Please refer to 5.2.1 Setting the Limits of the Chute Opener.
  • Page 21: Resolving Improper Positon Of Chute On Installation

    15-March-2018 To set the limits of the Chute, scroll down to ‘Edit Unit’ and press ‘Enter’. EDIT CHUTE After entering the Chute Edit Menu, ‘Set Limits’ will already be highlighted. Press SET CLOSE LIMIT SET OPEN LIMIT SAVE LIMITS ‘Enter’ POS: 2650/4096 ABORT = UP H:0.8.3 F:0.8.2...
  • Page 22: Changing The Unit Name

    15-March-2018 ‘Set Limits’ will be highlighted, press ‘Enter’. ‘Set Close Limit’ is highlighted and is the first one to be set. Use the ‘DIR1’ and ‘DIR2’ buttons on the remote to move the chute so it is completely closed and press ‘Enter’. If the chute opener stops but is not completely closed, look at the ‘POS’...
  • Page 23: Removing An Ez Opener Chute Opener

    15-March-2018 When finished changing the unit name, press ‘Enter’ to save the changes. Press ‘Exit’ to return to the Chute screen, and it will show the new name underneath ‘CHUTE 1’. EDIT CHUTE SET LIMITS 5.2.3 Removing an EZ Opener Chute Opener REMOVE UNIT EXIT EDIT UNIT NAME...
  • Page 24: Setting A Midway Stop Point

    This feature requires the firmware on the EZ Opener to be 1.5.7 or higher and the firmware on the R200 remote to be 1.1.8 or higher. Most of the older units can be sent to the manufacturer to be updated to...
  • Page 25: Locating The Hardware And Firmware Version

    15-March-2018 5.2.6 Locating the Hardware and Firmware Version EDIT CHUTE Enter into the ‘Edit Unit’ of the Chute Opener to find the hardware and SET LIMITS REMOVE UNIT firmware version. EXIT EDIT UNIT NAME H:0.8.3 F:0.8.2 The bottom line of the ‘Edit Unit’ states the hardware and firmware version. DIR1 DIR2 For the diagram the hardware version is 0.8.3 and firmware 0.8.2.
  • Page 26: Mic210 Side Chute Operation

    15-March-2018 5.3.1 MIC210 Side Chute Operation Enter into the Chute Menu by using the ‘Chute’ function button on the side of the remote or selecting ‘CHUTES’ from the Home Screen. CHUTE 1 00 40 B2 C2 78 MOTOR OFF If the desired side chute is not ‘CHUTE 1’ keep pressing the ‘Chute’ button to cycle HOME through the different chutes.
  • Page 27: Changing The Unit Name

    15-March-2018 5.3.2.3 Changing the Unit Name The main name will always be ‘CHUTE 1’ or 2 or 3 etc. but the description below it can be customized to represent a trailer or location. The new name can be a EDIT CHUTE maximum of 8 characters long.
  • Page 28: Operating An Auger Or Conveyhawk System

    15-March-2018 One Auger system can control up to three augers and on only on trailer. TARPS Example: A 3-Hopper trailer only requires one auger system, but a B-train would CHUTES require two auger systems. One auger system on the lead trailer controlling two AUGERS augers and one auger system on the rear trailer controlling two augers.
  • Page 29: Operating A Conveyor 'Conveyhawk' System

    15-March-2018 6.1.2 Operating a Conveyor ‘ConveyHawk’ System The conveyor system is found in the ‘AUGERS’ menu. The conveyor’s control screen can be accessed in the same way as an auger system. Enter into the Auger Menu by using the ‘AUGER’ function button on the remote or by selecting ‘AUGERS’...
  • Page 30: Programming A Conveyor, 2 Auger Or 3 Auger System

    15-March-2018 6.2.2 Programming a Conveyor, 2 Auger or 3 Auger System Enter into the ‘Edit Unit’ of the desired auger system. Use the up and down arrows to select the C or 2 or 3 on the line under EDIT AUGER REMOVE UNIT ‘AUGERS/CONVEYOR:’...
  • Page 31: Changing The Unit Name

    15-March-2018 6.2.4 Changing the Unit Name The main name will always be ‘TRAILER 1’ or 2 or 3 etc. but the description below can be customized to represent a TRAILER 1 EDIT AUGER trailer or location. The new name can be a maximum of 8 TEST 1 REMOVE UNIT AUGER AUGER AUGER...
  • Page 32: Creating A New Lights Screen

    15-March-2018 on continuously until the remote is paired. SETUP 1 The teach button will need to be used one more time ADD UNIT SETUP 2 15 MIN SHUTDOWN before securing the back lid back on. CHANGE NETWORK ID NO AUX FEATURE 68B0 NEW LIGHTS SCREEN ACCESS LIGHT UNIT...
  • Page 33: Accessing Each Individual Light Unit

    15-March-2018 There will be numbers 1 through 4 listed on the screen. Each one of these numbers represents a line which a unit containing lights can be added to. All units that occupy any of the four lines on the screen will be controlled by the ON or OFF button on the remote.
  • Page 34: Controlling The Chute Opener Light With The Remote

    15-March-2018 7.2.0 Controlling the Chute Opener Light with the Remote The remote must first have a Chute Opener paired to it; see Section 3.1.1 if the Chute Opener was not already added. Also, there must be a lights screen created on the remote.
  • Page 35: Controlling Multiple Light Units Manually From The T210 Remote Box

    15-March-2018 hold the teach button for at least 7 seconds on a unit which has lights that are to be controlled by the same lights screen. While still holding the teach button highlight the ‘ADD UNIT to SCREEN’ and press enter.
  • Page 36: Operating The Swing Auger

    15-March-2018 Once the Lights screen has been created or located select the ‘EDIT UNIT’ line. Press the button under ‘MORE’. A screen with the line ‘COPY SCREEN to UR’ should appear. Go to the T210 Remote box and press and hold the teach button until the red LED light above the button illuminates.
  • Page 37: Reversing Motor Direction

    15-March-2018 7.6.2 Reversing Motor Direction Once the remote is paired to a swing auger system the ‘IN’ and ‘OUT’ buttons may be backwards. Simply change the direction using the remote, without having to switch any wires. Enter the ‘Edit Unit’ of the swing auger which needs to be changed to change the EDIT SWING direction of the motor.
  • Page 38: Mic 210 Grain Truck Component Operation

    15-March-2018 8.0.0 MIC 210 Grain Truck Component Operation The main components on the grain truck box can all be controlled by one remote using Michel’s Integrated Wireless Technology. The three components which this section refers to are the electric tarp, the chute gate opener, and the hoist.
  • Page 39: Operating The Chute Gate Opener

    15-March-2018 Open or Close the chute gate. Edit Unit which allows changes to the description, reverse the direction of motor, remove the unit, and CHUTE 1 CHUTE 1 00 40 B2 C2 78 00 40 B2 C2 78 MOTOR OFF NO ANSWER find the hardware and firmware version.
  • Page 40: Reversing Chute Gate Opener Direction

    15-March-2018 8.2.2.2 Reversing Chute Gate Opener Direction Once the remote has been taught to the control box the ‘Open’ and ‘Close’ buttons may be backwards. Simply change the direction using the remote without switching any EDIT CHUTE wires. REMOVE UNIT CLOSE <=>...
  • Page 41: Hoist Menu

    15-March-2018 8.3.0 Hoist Menu The Hoist Menu operates similar to the Tarp Menu. To enter the TARPS Hoist Menu, simply press the ‘Aux’ function button on the side HOIST 1 00 40 B2 C2 78 CHUTES of the remote or select ‘AUXILIARY’ from the Home Screen. AUGERS HOME AUXILIARY...
  • Page 42: Removing The Hoist Control Box

    15-March-2018 8.3.2.1 Removing the Hoist Control Box It is possible to remove receivers which have been taught to the remote. EDIT HOIST REMOVE UNIT Enter the ‘Edit Unit’ menu. ‘Remove Unit’ should be highlighted. Press ‘Enter’ to CLOSE <=> OPEN ADD REMOVE A CHILD remove the unit.
  • Page 43: Warranty

    For the diagram the hardware version is 1.3.0 and firmware 1.3.6. 9.0 Warranty Michel's Industries warrants their products for a period of one year from date of purchase. Any parts returned to Michel's Industries LTD. will be shipped prepaid by the customer and will be returned F.O.B.

Table of Contents

Save PDF