Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Eicom ATC-700
- Page 2 Column Oven ATC-700 User’s Manual ATC700MAN_0802 ®2008 Eicom Corporation. All rights reserved.
-
Page 3: Table Of Contents
Table of Contents Introduction ………………………………………………………… Safety Precautions ……………………………………… 1-2 2. Specifications ………………………………………………… 3. Setup …………………………………………………… 3.1 Parts List ……………………………………… 3.2 Installation ……………………………………………… 3.3 Parts Names …………………………………………… 3.4 Power …………………………………………… 4. Operation …………………………………………………… 4.1 Display Panel …………………………………………… 4.2 Operations Keys ……………………………………………… 4.3 Display ………………………………………………... -
Page 4: Introduction
The ATC-700 performss best when using with Eicom HPLC Pumps System EP- 700 and Eicom ECD-700. The ATC-700 has a Peltier device to heat and cool the air inside the chamber by convection. At the normal setting temperature range near room temperature, the temperature regulation will be at the +/- 0.1°C accuracy. - Page 5 Do not cover the ventilation slits on the back and side pannel of the ATC-700. If Caution you do so, the electonic parts may overheat and be damaged. Please keep a distance of at least 10 cm between objects and the ATC-700.
-
Page 6: Specifications
3 . S etup 3.1 A list of the parts in the package When you open the box, please confirm if the package contains the following accessory parts. List of Accessory Parts includedin the ATC-700 package Item Code Remarks User’s Manual... -
Page 7: Installation
Please keep objects away at least 10 cm for the side, front and back panels. Do not put something other than another Eicom 700 series component on top of the ATC-700. Place the ATC-700 on a level and sturdy bench top in an indoor laboratory which meets the following requirements. -
Page 8: Parts Names
3.3 Parts Names Main Door Front View Auxillary Door Temperature Display Inside Compartment Grounded Column Clips Open Door Sensor Vent for fan and Peltier device Main Power Inlet/ Outlet Tubing Ports Switch Left Side Right Side View View Cooling Fan Main Power Receptacle Fuses... -
Page 9: Power
3.4 Power Supply Always use the power cable came with the machine. Power Voltage ： AC 100V ～ 240V (±10V) Frequency ： 50-60 Hz Consumption ： 210 W 4 . Operation 4.1 Display Panel Temperature Display Increase/Decrease Buttons Display Panel 4.2 Operation Keys Name Function... -
Page 10: Display
4.3 Display PT displays the current temperature and ST displays the set point temperature. Current Temp Set Point Temp 4.4 Main Power ON/OFF The main power ON/OFF is located on the left side as you face the instrument. After the initial display, the display will show the status. ＜... -
Page 11: Operation
4.5 Operation How to change the setting temp Turn the main power on Status Display appears after initialization To set the temperature up, hit ▼ key To set the temperature down, hit ▲ key At the ST Mark will appear When the required temperature is shown at ST, hit SET Key PT will match ST, when the new... -
Page 12: Error Messages
Then turn on again. If the error persists, (with please contact us. beep) . Ventilation Duct This ventilation duct comes with the ATC-700 and can be installed according you your needs. If you need to attach the duct by yourself, please contact us. -
Page 13: Limited Warranty
Warranty Period: One year from the original purchase date as defined by the date of your Eicom invoice. Warranty Information: During the warranty period, this Eicom product is covered by a limited liability warranty covering manufacturer defects. In the case that the machine is defective, it will be repaired or replaced free for charge.
Need help?
Do you have a question about the ATC-700 and is the answer not in the manual?
Questions and answers