Advertisement
2. INTRODUCTION & SPECIFICATIONS
Manufactured from corrosion resistant materials with stainless steel motor case and noryl base cover. Minimum water depth of just 8mm.
Designed for clean water although this pump will accept small particles up to 5mm. Suitable for the effective drainage of cellars, sinks,
cisterns, baths and the general transfer of water. The WPc100A, WPc150A and WPc235A feature an automatic low water cut-out.
Model No.
Cut-Out
WPc100
Manual
WPc150
Manual
WPc235
Manual
WPc100A
Automatic
WPc150A
Automatic
WPc235A
Automatic
3. OPERATING INSTRUCTIONS
WARNING! Ensure you read, understand and apply safety instructions.
Important: The maximum continuous running time for the pump is six hours, to be followed by
three hours downtime.
3.1.
fit appropriate discharge pipe to pump outlet and secure with clip. Ensure the diameter of the discharge
pipe is same as or greater than the outlet diameter as a smaller pipe will adversely effect the pump flow
rate.
3.2.
Position pump in the water accordingly, and place the outlet pipe securely in the discharge receptacle or
area. We recommend that the pump is sunk with its discharge outlet facing up to release any trapped air.
3.3.
Plug the pump into the electrical mains supply and switch on.
The automatic versions will automatically turn on as the level of water rises (fig 2.A). As water level lowers,
the float will automatically switch the pump off as it reaches the minimum height (fig 2.B). float may be
adjusted by shortening or lengthening the cable. The pump will switch on if the water level is up to or
above the maximum length of the float cable. To function correctly the float must move freely. Ensure the
float can do so and that the cable is not restricted. check that the pump and discharge are working
correctly.
3.4.
The water into which the pump is placed will act as the motor cooling agent. for this reason the pump
must remain submerged at all times. Should the pump have to be used in shallow water Do noT operate
for more than 10 minutes. failure to follow this rule will damage the unit and will invalidate your warranty.
NOTE: See figure 3 to determine minimum clearance required if using pump in a restricted area i.e. well, etc.
4. MAINTENANCE
WARNING! With the exception listed below, all pump, float and electrical cable service maintenance and repair must only be
undertaken by an authorised service agent. Failure to observe this rule may be dangerous and will invalidate your warranty.
WARNING! Ensure the pump is disconnected from the mains power supply before attempting any service or maintenance.
4.1
Keep all parts of the pump clean. rinse, drain and allow to dry before storing pump.
4.2.
regularly check the water inlet on the base of the pump to ensure there are no blockages. To access the impeller carefully undo the
base hex headed screws and remove base. clean impeller and replace base ensuring that the "o" - ring is correctly located.
Do noT dismantle any other part of the unit.
TROUBLESHOOTING
1. Water level below min suction depth.
a. Motor operates but
2. Air bubbles in pump accumulated during submersion,
there is no suction.
3. clogged intake filter or discharge pipe
b. reduced water
1. Discharge pipe bent, or pinched.
volume for level
2. Discharge pipe too narrow.
of water
3. Pump partially blocked.
c. The pump will not start
1. no electrical power.
or suddenly stops
2. float not working
during operation.
3. Impeller is jammed.
Parts support is available for these products. To obtain a parts listing and/or diagram, please log on to
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Outlet OD
Max. Output
32mm
100ltr(22gal)/min
32mm
150ltr(33gal)/min
38mm
235ltr(51gal)/min
32mm
100ltr(22gal)/min
32mm
150ltr(33gal)/min
38mm
235ltr(51gal)/min
or float is incorrectly positioned so pump does not stop
at minimum level and sucks in air.
www.sealey.co.uk, email sales@sealey.co.uk or phone 01284 757500.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7Ar
Original Language Version
Max. Head
Motor
7mtr
250W
8mtr
400W
9mtr
750W
7mtr
250W
8mtr
400W
9mtr
750W
1. Stop the pump.
2. release air by inclining the pump and
re-immersing it in water.
3. remove blockage, and clean the unit.
1. Straighten pipe
2. use wider diameter pipe.
3. clean pump.
1. check cable, plug and fuse.
2. contact authorised service agent.
3. clean the pump.
01284 757500
01284 703534
WPc100, WPc100A, WPc150, WPc150A, WPc235, WPc235A
Input
Max. Submersion Depth
230V
230V
230V
230V
230V
230V
www.sealey.co.uk
Web
sales@sealey.co.uk
email
Issue: 4 - 19/12/11
6mtr
8mtr
8mtr
6mtr
8mtr
8mtr
fig 2
fig 3
Advertisement
