Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for INAZUMA WebCSA Series
- Page 1 w w w . i n a z u m a - o n l i n e . c o m Operating Instructions Control WebCSA, App & Accessories The initial setup of the control requires an iOS device with an active SIM card Control WebCSA iOS version Power Switch WebCSA Add-On...
-
Page 2: Table Of Contents
Configuration of the control without App or WLAN ..6 warnings WebCSA App & Inazuma WebCSA Cloud ... . . 7 Please store this manual at an accessible location to be Registration and installation . -
Page 3: Ec Declaration Of Conformity
Sensor WebCSA and / or the water level regulation 1.8. Spare parts WebCSA is limited to the respective device. Only spare parts provided by Inazuma or one of its The liability does not cover defects caused by accidents authorized suppliers are approved for installation. In the... -
Page 4: Control Webcsa
2. Control WebCSA 2.1. Connections 1. Mains Plug 2. Gear motor 3. High pressure pump 4. UVC 5. UVC 6. Power-Switch P1 Power-Switch P2 (optional function) 8. Power-Switch P3 (optional function) 9. Power-Switch P4 (optional function) 10. Cover switch 11. Magnetic valve for rinsing flush 12. -
Page 5: Mounting Of The Control Unit
If the water sinks below the level of the bottom float switch, the filter will turn off automatically, or else a continuous irrigation would occur. Inazuma offers an automatic pond level ® regulation (item no. IK5001) -
Page 6: Configuration Of The Control Without App Or Wlan
ATTENTION: If you configure the control unit 5. Configuration of filter and installation type with the app, you can proceed directly with move the floater SS1 step 3.1. within 30 seconds • 1 x up & down = drum filter - gravity setup 2.7. -
Page 7: Webcsa App & Inazuma Webcsa Cloud
2. Connect the float switches 1 + 2 to the control, set float switch in reset mode (see left picture) 3. Connect the control to the mains 4. Open the Inazuma WebCSA app on your mobile or tablet 5. The starting process of the control unit takes about 1 to 2 minutes. - Page 8 12. Selecting your WLAN To set up the control, you must change the To connect the control unit to your home name of your phone to Inazuma WLAN, select your home connection from the list. To do this, go to Settings >...
- Page 9 18. Log in to the WebCSA cloud 15. Log in to the app In order to be able to see the filter status In the start screen of the Inazuma app, click outside your home network, it is necessary on the IP address tab.
-
Page 10: Main Screen
3.2. Main screen Mode Help The currently set “mode” is displayed. By tapping you can switch Opens up the help page for the current page. between the modes summer - autumn - winter. Summer: Depending on the degree of soiling, flushing is carried out Power Switch [P1] ([P2] [P4] [P4] Art.Nr. -
Page 11: Power Switch
All functions of the Power Switch can be programmed and operated via the Inazuma WebCSA App. To be able to switch on the channels manually in the app, it is necessary to create at least one switching point for each Power Switch output. -
Page 12: Water Level Regulation (Optional)
5.2. Connection to the control (optional) Always disconnect the power plug before connecting / The Inazuma water level control is an electric, fully disconnecting components or opening the control unit! automatic control unit for the compensation of water losses on koi-, swimming-, garden- and ornamental ponds. -
Page 13: Temperature Sensor (Optional)
Make sure that the app has a 6.1. Connection to the control connection to the Inazuma WebCSA Cloud (setting in the login screen of the app) Always disconnect the power plug before connecting /... -
Page 14: Updating The Control Webcsa
8. Updating the Control WebCSA 9.2. Mounting float switch 2 (gravity) 8.1. Automatic Update For optimum operation of the WebCSA control we recommend activating the automatic update function of the control. This requires an internet access / WLAN connection to the control unit. -
Page 15: Mounting Float Switch 2 (Pumped)
w w w . i n a z u m a - o n l i n e . c o m The exact position of the float switch must be adjusted individually (slot holes in the mounting). The height depends on the power of the pump. 9.3. -
Page 16: Eisackstraße
Eisackstraße 16 DE – 86165 Augsburg Tel. : (+49) 821 - 72 919 72 Fax : (+49) 821 - 72 919 73 info @ inazuma -online .com www. inazuma- online .com Technical modifications and errors excepted WEEE-Reg.-Nr. DE 19429673 Manual version 2019-08 / 1.2...