Summary of Contents for Carp Sounder CS Radio System
- Page 1 Operating instructions CS radio system AGE ONE Digital Wireless Bite Alarm Campsecure Infrared alarm system CS Receiver Digital radio receiver...
- Page 2 Always keep this manual in a safe place so that you can access it at any time. We wish you a lot of fun with your Carpsounder product and successful hours on the bank. Team Carp Sounder...
- Page 3 Inhalt: AGE ONE bite alarm Digital wireless bite alarm of the new generation. Campsecure alarm system Infrared alarm system to secure the fishing spot. CS Receiver Digital radio receiver of the new generation.
- Page 4 AGE ONE Bite alarm: Technical specifications: ● Attractive, robust polyamide housing ● 100% waterproof ● LED color adjustable (7 colors + off) ● Afterglow time of the LED approx. 20 sec. ● LED can be switched off ● Night light can be switched on ●...
- Page 5 AGE ONE Bite alarm: Controls LEDs Buttons ( 1 ) ( 2 ) ( 3 )
- Page 6 AGE ONE Bite alarm: Signal tones: Bite: Bites are indicated by short notes corresponding to the cord pull. The LEDs of the bite indicator light up in the preset color for approx. 20 seconds. The CS receiver signals a single tone and a 20-second LED. Drop bite: Bites are indicated by short double tones corresponding to the cord pull.
-
Page 7: Switch On The Device
AGE ONE Bite alarm: Switch on the device: Hold the button (2) for about 3 seconds. The device will now turn on and perform a self-test, playing a tone sequence. By flashing the LEDs 4 times, the battery charge status is displayed. -
Page 8: Adjust Sensitivity
AGE ONE Bite alarm: Adjust sensitivity: The adjustment of the sensitivity is carried out with the button (1). Sensitive ❶ ❷ ❸ ❹ ❺ Insensitive The set level is indicated by fast or slow flashing of the LEDs and a matching tone sequence. The LEDs flash green at maximum setting, red at minimum, and blue in between. -
Page 9: Nightlight On / Off
AGE ONE Bite alarm: Set LED color: Turn on your AGE ONE bite alarm. Hold down the button (3) permanently. The LED color now changes in the following order: ❶❷❸❹❺❻❼❽ When the desired color is displayed, release the button (3). The LED color is now taken over and saved. Nightlight On / Off: Turn on your AGE ONE bite alarm. -
Page 10: Reset To Factory Settings
• Volume ❺ • Pitch ❾ • Night light • Radio code Caution: When reset, the AGE ONE switches completely to factory settings. The code for the CS radio system is recreated. The device must be reconnected to the CS receiver. -
Page 11: Changing The Battery
AGE ONE Bite alarm: Changing the battery: Open your bite alarm by loosening the four screws in the corners of the case. Replace the battery inside with a new one and close the housing again. Required battery: 1 x CR123A Caution: When closing the housing, make sure that the seal is seated correctly and that no cable is trapped between the housing halves. - Page 12 Campsecure transmitter: Technical specifications: ● Attractive, robust polyamide housing ● 100% waterproof ● LED lighting can be switched off ● Operation with 3 standard AA batteries (incl.) ● Integrated radio transmitter module ● Transmission of the LED color to the receiver ●...
- Page 13 Campsecure transmitter: Controls: Buttons: ( 1 ) ( 2 )
- Page 14 Campsecure transmitter: Switch on the device: Hold the button (1) for about 3 seconds. The device will now turn on and perform a self-test. By flashing the LED 3 times, the battery charge status is displayed. Green > 80 % ï❸ð...
-
Page 15: Set Sensitivity
Campsecure transmitter: Set sensitivity: Press the button (1) to adjust the sensitivity. The LED now flashes once in the color of the set sensitivity level. Sensitive ❶ ❷ ❸ Insensitive There are a total of 3 levels adjustable of which the most sensitive is indicated by a green LED. - Page 16 The switch position XRS selects the XRS radio system. Long key press on key (2) carries out the radio coding. Switch position ONE: The switch position ONE selects the CS radio system. Long press on button (2) to adjust the LED color...
- Page 17 Campsecure transmitter: Radio coding XRS: Switch on your XRS receiver and your Campsecure transmitter. At Campsecure, press and hold the button (2). The LED color changes 8x 4 times from red -> yellow -> green -> blue ❶❷❸❹ As soon as the desired LED on your XRS receiver flashes and sounds, release the button (2) to save the setting to the desired LED.
- Page 18 Campsecure transmitter: Set LED color (ONE only): This function is only available if the system ONE is set in Campsecure. See point Select radio system. Turn on your Campsecure transmitter. At Campsecure, press and hold the button (2). The LED color changes in the following order: ❶❷❸❹❺❻❼❽...
-
Page 19: Installation Recommendations
Campsecure transmitter: Installation recommendations: Point the Campsecure Sender to the object or area to be monitored. Fix the transmitter with the rod (Bankstick, Stormrod) firmly and wobble-free in the ground. The installation height should be approx. 1m. Go through the monitoring area and make sure that you have positioned the transmitter correctly. - Page 20 XRS radio coding has been changed, it must be set again (see Radio Coding XRS). The code for the CS radio system is recreated. The device must be reconnected to the CS receiver.
- Page 21 Campsecure transmitter: Changing the battery: Open your Campsecure transmitter by loosening the four screws of the housing. Replace the batteries with new ones and close the housing again. Required batteries: 3x LR6 1.5V AA Troubleshooting: No function:: Batteries empty, defective or inserted incorrectly. Device sends no or false alarms: Heavy fog or heavy rain can cause false alarms.
- Page 22 CS Receiver: Technical specifications: ● Compact housing (87 x 52 x 33 mm) ● 100% waterproof ● Digital volume adjustment ● ACC light (for transmitters with ACC support) ● Vibration function in sync with sound ● Acceptance of the LED color from the bite indi- cator ●...
- Page 23 CS Receiver: Controls: LEDs Buttons ( 1 ) ( 2 ) ( 3 )
- Page 24 CS Receiver: Switch on the device: Hold the button (2) for about 3 seconds. The device will now turn on. By lighting up the LEDs, the charge status of the batteries is displayed. ==== Battery full Battery OK Change battery Weak batteries are indicated by 4 flashing red LEDs and a warning sound hourly.
-
Page 25: Vibrating Alert
CS Receiver: ACC light function: (only transmitters with ACC support) Hold down the button (1) for about 3 seconds. When the ACC light is switched on, it will be switched off and the LEDs will briefly light up red. This sounds a low receipt tone. - Page 26 CS Receiver: Registration of devices: If no device is paired with the CS receiver, the first LED quickly flashes red after switching on. ï❶ð The channel is ready for registration. Up to 16 devices can be registered. Turn the 1st bite alarm / Campsecure on and off again. Upon successful login, the first LED will show a steady green light ❶...
- Page 27 CS Receiver: Reset to factory settings: Hold down the button when turning on your CS receiver (2) continue to press for about 8 seconds. A 3-way tone and red LEDs indicate a successful reset. The device restarts with the following settings in the registration mode: Default settings: •...
- Page 28 CS Receiver: Changing the battery: Open your receiver by loosening the two screws on the back of the case. Replace the batteries with new ones and close the housing again. Required batteries: 2x LR6 1.5V AA Lithium We recommend the use of lithium batteries for optimal battery life and radio range.
- Page 29 CS Receiver: Troubleshooting: No function: Batteries empty, defective or inserted incorrectly. All 4 LEDs flash permanently red quickly ï❶❷❸❹ð Battery voltage too low for operation. Change the batteries. First LED flashes quickly red ï❶ð There are no devices connected to the CS receiver. Registration is in progress.
- Page 30 CS radio system: Tipps & Tricks: CS Receiver LEDs bei der Anmeldung am CS Receiver überspringen: Skip LEDs when logging on to the CS receiver: Do you have e.g. 2 Bite indicators and want to display them on the 1st and 4th LED of the CS receiver, it is necessary to skip the LEDs 2 and 3.
- Page 31 CS radio system: Tipps & Tricks: Bite alarms In winter, prevent the roller wheel from freezing: Especially in autumn and winter, the combination of high humidity and later onset of frost can cause the roller wheel of the bite alarm to freeze.
- Page 32 SIMPLIFIED EU DECLARATION OF CONFORMITY Hereby Carpsounder Braunfels e. K. declares that the radio equipment type CS radio system in all its devices complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following Internet address: www.carp-sounder.de/ce/...
- Page 33 Disposal: This device does not belong in the household waste. For proper disposal, please contact the public collection points in your community. For details of the location of such a collection point and about any existing quantity restrictions per day / month / year and about any costs incurred in collection, please refer to the information of the respective municipality.
-
Page 34: Warranty
Warranty: 1. You get 3 years warranty on this device from the date of purchase. Please keep invoice / proof as proof of purchase. In case of warranty, please contact our service. 2. The provision of a replacement device during the repair period is not included in the warranty. - Page 36 Carpsounder Braunfels e. K. Josef-Lücker-Weg 6-8 35619 Braunfels Germany Tel.: +49 (0) 64 42 - 51 52 Fax: +49 (0) 64 42 - 3 14 31 E-Mail: info@carp-sounder.de...