1. Manuals
  2. Brands
  3. Keyland Laser technology Manuals
  4. Printer
  5. 1390 Series
  6. User manual

Keyland Laser technology 1390 Series User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Jiangsu Keyland Laser Technology Co.,Ltd
All rights reserved
 Keyland Laser Technology Co.,Ltd reserves the right to modify the products in
this manual and product specifications document without prior notice.
 Keyland Laser Technology Co.,Ltd does not assume caused by improper use of
the manual or the product directly, indirectly, incidentally or consequential loss
or liability.
 Keyland Laser Technology Co.,Ltd has the products and software patents,
copyright and other intellectual property rights. Unauthorized and shall not
directly or indirectly copy, manufacture, processing, use of this product and its
associated parts
 This product is designed and manufactured for general industrial applications
than expected and the use of human life or property caused by the significant
impact is not the scope of services
 Keyland to ensure that: all "Gosun and keylandr" brand products will improve
service to the Company
Statement
46-1

Advertisement

Table of Contents
loading

Summary of Contents for Keyland Laser technology 1390 Series

  • Page 1 Jiangsu Keyland Laser Technology Co.,Ltd All rights reserved  Keyland Laser Technology Co.,Ltd reserves the right to modify the products in this manual and product specifications document without prior notice.  Keyland Laser Technology Co.,Ltd does not assume caused by improper use of the manual or the product directly, indirectly, incidentally or consequential loss or liability.
  • Page 2 Preface Thank you for trust on Keyland Laser technology Co.,Ltd., welcome to use our products! Please read this user manual before using the product.This manual provides detailed information for use firstly of this product relevant security matters, the installation, describes the function , operation of the various components, the routine maintenance necessary for the good condition of this product, and lists the fault finding methods, techniques, support files, and more important content.
  • Page 3 In order to ensure safe operation and best performance, please follow these warnings and pay attention to other matters, as well as the manual to operate.  "Dangerous" and "warning" symbol are marked in accordance with the extent of the risk of accident. Indicates a potentially hazardous situation , if not avoided, may result in death or serious injury Indicates a potentially hazardous situation if not avoided,...

  • Page 4: Table Of Contents

    radiation. Contents 1. Security ......................6 1.1 Basic information ................. 6 1.2 Optical Security ..................6 1.3 Electrical safety ..................8 1.4 Equipment safety standards ............... 9 2. Overview ..................... 10 Introduction ..................10 2.1.1 Character ................... 10 2.1.2 Application ................. 11 Operating principle and parameters ..........
  • Page 5 4. Operating instructions ................22 4.1 Booting process ................... 22 4.2 Use the operating ................22 4.2.1 Operation panle ................22 4.3 Shutdown process ................25 5. Maintenance service ..................26 5.1 Maintenance and servicing of the optical system ......26 5.2 Maintenance and servicing of motion organizations ......

  • Page 6: Security

    1. Security 1.1 Basic information  The staff , who can be authorized after the relevant training and fully understand the necessary safety procedures, can operate this laser productcan  Please allow only authorized person close to the laser product, set the appropriate warning signs.
  • Page 7 specular reflection of accidental damage to the human eye or the human body.  Strongly recommended that the laser output port do not point to the entrance or windows of the room when the product is placed  "Beware of the laser, do not close" words of warning signs should be set to equipment workplace door or near the work area May lead to the occurrence of fires and other accidents ...

  • Page 8: Electrical Safety

    Paste on the laser front 1.3 Electrical safety This device contains a fatal DC and AC voltage, even if powered off This danger may still exist for some time  This product must be in the specified electrical conditions.  Connect the power line and ensure that the circuit wiring is correct. ...

  • Page 9: Equipment Safety Standards

     Avoid to boot work in thunder and lightning Prohibit unauthorized adjustment, demolition, replacement in Unauthorized condition. Doing so may result in injury or equipment damage  Humidity too high cause high-pressure laser discharge, endangering personal safety, will cause damage to the laser power ...

  • Page 10: Overview

    2. Overview Introduction The 1390 series laser cutting machine is widely used in non-metallic materials cutting (such as acrylic, leather, cloth, etc.). The machine adopts the glass tube of carbon dioxide laser as the light source, computer-controlled two-dimensional platform for various pre-set graphics track precise movements. Laser of the model set, automatic control, precision machinery, computer control software, and other high-tech one, with high-tech, high cost performance characteristics.

  • Page 11: Application

    resolution up to 0.02mm. 3, The flying opticsoptical systems, processing large format; device on three sides to take the open design of convenient material. 4.Support a variety of general-purpose graphics software to generate PLT, BMP (1 bit) and DXF file formats, can produce a variety of graphics, text, graphic, specification.

  • Page 12: System Structure

    Cooling water ℃～ ℃ Power 110V/60Hz/2KW temperature System structure The 1390 series laser cutting machine from the operator panel, cabinet, laser, working platform, constant temperature water-cooled machines, negative pressure vacuum fans and other systems 2.3.1 Appearance Front machine 46-12...
  • Page 13 Emergency stop switch Back of machine Total power connector In and outlet chiller pipe Ground terminal Side of machine 46-13...

  • Page 14: Main-Operation-Contro-Panel

    Total power switch Exhaust Laser power switch 2.3.2 Main-operation-contro-panel 46-14...

  • Page 15: Co2 Laser

    1 Start/Pause 2 Frame 3 Enter 4 Turn Right 5 Upwards 6 Z/U 7 Downwards 8 Turn Left 9 Screen 10 Esc 11 Origin 12 Reset 13 Laser 14Speed 15 MiniPower 16Max.power 17 File 2.3.3 CO2 Laser Laser Light exit positive lines Connected with negative line 2.3.7 Working platform...

  • Page 16: Thermostatic Water-Cooled Machine

    2.3.5 Thermostatic water-cooled machine Temperature display Switch properly working indicator Warning light 2.3.6 Electronic control board 36V Power Swith Relay Filter 46-16...

  • Page 17: Negative Pressure Vacuum Fan

    2.3.7 Negative pressure vacuum fan Inlet duct connector Outlet duct connector 46-17...

  • Page 18: Installation &Adjustment And Workflow

    3 Installation &adjustment and workflow 3.1 Opening inspection After opening the package, please check carefully : The appearance of equipment is in good condition; inventory of products and accessories are complete according depending to device packing list. If you find a product model does not match, or damaged, and missing accessories, do not use and contact us promptly 3.2 Preparation before installation and adjustment...

  • Page 19: Processing Workflow

     Single-phase three-wire (110V/10A), should be directly connected to the protection of the earth terminal to install leakage protection switch.  The corresponding specifications of the air switch installed in the wall over two meters away from the equipment station, height of 1.2 meters. If the local grid voltage instability or low, if necessary, with the power supply of the corresponding specifications ...

  • Page 20: Processing Notes

    、 Place the working material , use the reset button on the control panel so that the laser head back to the starting position. 、 The use of focus adjustment rules, adjusting focus tube up and down position according to the processing of the material thickness . 、...
  • Page 21 、 Shall not be placed objest to impede the laser heads running in the machining area in order to the stepper motor is not blocked out of step processing defects. 、 The whole process must ensure that the circulating cooling water should be at regular intervals (per hour) observation of the cooling water temperature,and replace clean water timely.

  • Page 22: Operating Instructions

    Operating instructions 4.1 Booting process The boot process in the main operation table  Open red (motion control) button switch.  Keep pressing "water button" switch until lights. ※ Pressing about five seconds till the cooling water tank to start, about 10 seconds, "WATER / cooling“...
  • Page 23 Z&U 显示屏 确定 退出 定位 边框 最大 启动 最小 点射 速度 复位 文件 功率 功率 暂停 、 Keyland touch screen The LCD screen shown on the document name or system parameters: cutting speed, work intensity, and system state (initialization, wait, pause, etc.). 、...
  • Page 24 emitting again each time . Hold down the "Laser" button, the laser tube lights emitting up to a light in 0.5 seconds.This key is valid only in a wait or pausestate of the system in ; other state invalid Speed: Set the cutting speed, 0% -100% optional . This key is valid in wait or pause , others are invalid.

  • Page 25: Shutdown Process

    Exit: to cancel the operation. The abolition of the changes made when set the cutting parameters; It will deselect when it was for choose operating documents, ; It can make System return to waiting state when sysytem is in pause state. Other state, "Exit"...

  • Page 26: Maintenance Service

    Maintenance service 5.1 Maintenance and servicing of the optical system  CO2 laser tube to replenish the gas or replacement of the laser tube, especially when the laser tube was working time over 1000 hours, please feel free to pay attention to the output power of the laser tube;In the same current conditions if the power is smaller you need to replace the laser tube.

  • Page 27: Maintenance And Servicing Of Motion Organizations

    5.3 Optical path adjustment and replacement of the laser tube Ptical path adjustment 1390 series engraving machine in use, there may occur the optical path offset, resulting in the phenomenon of no light or light path errors will directly affect the processing efficiency and effects, attention should be paid.
  • Page 28 X 1 Y1 X 2 Y1 X 1 Y2 X 2 Y2 1 laser Tube 2 First reflector 3 Second reflector Third reflector 5 Focus tube 6 Workpiece 7 Workpiece carrying platform The optical system of the machine is as shown above, the adjustment of the optical system shall start from transmitter 、...
  • Page 29 、 A small organic board caught in the first reflector surface and fine-tune tto adjust the frame of laser tube , and used in conjunction with the test button (click), so that the laser emits completely in the first reflector and try to place the first reflector in the middle.
  • Page 30 近端调节 远端调节 调节二反 Fine-tuning second mirror 、 Place a small organic board clips onto the top of the focusing tube, fine-tuning the third mirror adjustment knob, and use in conjunction with the test button (click), so that the third mirror launchs reflecting the laser can completely focus in laser tube as much as possible and focus on the middle of the lens (Note, smoke maybe cause pollution to the third reflective lenses ,should avoid the smoke generated by the third reflection of the lens).

  • Page 31: Thermostatic Water-Cooled Machine Maintenance And Servicing

    Fine-tuning third 调节三反 mirror Organic board 有机板 、 The above adjustments will directly affect the processing effect , pls repeatedly adjust carefully 5.4 Thermostatic water-cooled machine maintenance and servicing  Regularly clean and replace laser chiller water per week. Water quality will directly affect the normal use and life of the equipment, Water causes damage to the equipment is not out of warranty...

  • Page 32: Exhaust Fan And Vacuum Pipe Maintenance And Servicing

    5.5 Exhaust Fan and vacuum pipe maintenance and servicing  Regular cleaning of internal dust of Exhaust Fan and vacuum pipe internal dust per three month 46-32...

  • Page 33: Common Problems And Solutions

    6 . Common problems and solutions 6.1 The main equipment part Please operate the following adjustments under the guidance of our technical staff  Fault phenomenon: Turn the key switch, nothing happens Fault Solution Total power switch is closed Close the power switch Power is plugged in or not Cheak it The power switch is damaged...
  • Page 34 Fault Solution Laser power settings are not normal Setting normal laser power Cutting/engraving parameter is not effect Set suitable parameter The laser output becomes weaker Set suitable parameter  Fault phenomenon:Cutting /engraving size 's error or malfunction Fault Solution Signal line is not working properly Replace signal line Machine and the computer grounding is Good grounding equipment and...

  • Page 35: Thermostatic Water-Cooled Machine Part

    6.2 Thermostatic water-cooled machine part  Fault phenomenon ： The boot without power Fault Solution Power line ‘s contact is not good Cheak power plug Insurance tube fuse Cheak it and replace  Fault phenomenon ： Flow alarm Fault Solution Check the water level, adding recycling Water tank water level is too low water,check waterways for leaks...
  • Page 36 Fault Solution Water inlet is not open Open it 46-36...

  • Page 37: Drawings

    7 . Drawings 7.1 Outline Drawing 46-37...
  • Page 38 46-38...

  • Page 39: Electrical Schematic

    7.2 Electrical schematic 46-39...

  • Page 40: Electrical Wiring Diagram

    7.3 Electrical wiring diagram 46-40...
  • Page 41 46-41...
  • Page 42 46-42...
  • Page 43 46-43...
  • Page 44 K3孔插头 46-44...

  • Page 45: Consumable Wearing Parts

    8 . Consumable wearing parts 8.1 Laser tube When the laser power decay gradually and can not cut normally. After the exclusion of other factors, you need to replace the laser tube. 8.2 Optical Lens The optical lens is contaminated, the laser will damage the coating layer of lens . Should be replaced at this time.

  • Page 46: Sftware Operation Manual

    9. Sftware Operation Manual Software Introduction The software of 1390 series laser engraving machine is for the small-format series laser engraving machine, is designed to develop application software. The software interface is friendly, functional, and easy to use . The installation of the software program Please check attachment 9.3 Software Operation...

Table of Contents