Summary of Contents for UBEXi iDIG
- Page 1 User Manual Extra Sensor Manual Version: 1.02 Software Version: 1.00 Language: English www.ubexi.com more detailed information.
- Page 2 Safety Information: Magnets Use caution with the powerful magnets in iDig mounting plates The mounting plates used to secure the sensors to the excavator use extremely strong rare earth magnets. They must be handled with care to avoid personal injury and damage to the magnets. Fingers and other body parts can get severely pinched between two attracting magnets or other metal surface.
-
Page 3: Safety Labels
Use the system to dig with an excavator to a desired depth and create a With iDig, the operator has to dig “straight ahead” (only moving the leveled plane or to set a slope and create a tilted surface. Also use it to booms/bucket in and out). -
Page 4: Electromagnetic Compatibility (Emc)
Safety Information: Radio PRECAUTIONS The product must not be disposed with household waste. Dispose of the product appropriately in accordance with the national regulations in force in your country. FCC Labels on sensors & LED Display ELECTROMAGNETIC COMPATIBILITY (EMC) Description The term Electromagnetic Compatibility is taken to mean the capability of the product to function smoothly in an environment where electromagnetic radiation and electrostatic discharges are present, and without causing electromagnetic disturbances to other equipment. -
Page 5: Fcc Statement, Applicable In U.s
Safety Information: Radio FCC STATEMENT, APPLICABLE IN U.S. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. -
Page 6: Content Of Delivery
Content of Delivery Sensor with base plate Magnetic Mounting Plate... - Page 7 Sensors & Magnetic Plates Each sensor may be marked for use on a specific element Second boom: Chassis: Attach anywhere on Attach on cab, oriented the same way as the other sensors the second boom (vertical) and not too close to the engine (too much vibration). Use magnetic mounting plates to attach sensors 1) Place sensors on magnetic plates.
- Page 8 Assign the new Sensor 1) Install suction cups on the windows of the cab. 2) Attach cradles for the control unit and LED display. 3) Snap control unit and LED display into the cradles. 4) Plug the power cable into the cigarette lighter outlet. Important: Do not attach the sensor to the magnetic plate yet!
- Page 9 Assign the new Sensor Long-press ENTER to get into the User Menu. Press the DOWN arrow once to get to SYSTEM SETTING. Press ENTER to access the SYSTEM SETTING menu. Press the DOWN arrow once to get to ADD SENSOR. Press ENTER to access the ADD SENSOR menu.
- Page 10 Assign the new Sensor Choose with the arrow keys to which element you want to assign the new sensor to (2nd boom, chassis,….). Switch ON (attach to magnetic plate) the new sensor. After successful programming the system indicates success and returns to the „ADD SENSOR“...
- Page 11 Calibrate the Chassis (Pitch) Sensor Attach the new chassis sensor to its final location. Long-press Long-press ENTER to get into the User Menu. Press the DOWN arrow once to get to the SYSTEM SETTING. Press ENTER to access the SYSTEM SETTING menu. Press 4 times Press the DOWN arrow 4 times to get to the CHASSIS...
- Page 12 Calibrate the Chassis (Pitch) Sensor Press ENTER to ENABLE the PITCH compensation. Press ENTER to access the CHASSIS ANGLE CALIBRATION. Align the cabin parallel to the tracks. Press ENTER to register this position. Don‘t move until the point is successfully registered. Rotate the cabin 180°.
- Page 13 Calibrate the Chassis (Pitch) Sensor Press ENTER to register this position. Don‘t move until the point is successfully registered. CHASSIS ANGLE CALIBRATION done. Do not move the sensor anymore from this point on. Press the DOWN button once to proceed to the SET SEGMENT AB menu.
- Page 14 Calibrate the Chassis (Pitch) Sensor Note: -B is the theoretical center of the Press ENTER to set the machine segment length B-C. Use the -C is the pivot point between main arrow keys to dial-in the value. boom & chassis -Measure the vertical Distance between B and C Chassis Calibration done.
- Page 15 Calibrate the 2nd Boom Sensor (or New Machine Calibration) Attach the new 2nd boom sensor to its final location. Long-press Long-press ENTER to get into the User Menu. Press the DOWN arrow once to get to the SYSTEM SETTING. Press ENTER to access the SYSTEM SETTING menu.
Need help?
Do you have a question about the iDIG and is the answer not in the manual?
Questions and answers