Subscribe to Our Youtube Channel
Summary of Contents for Finwing SABRE 1900
- Page 1 FINWING SABRE 1900 FINWING SABRE 1900 U S E R M A N U A L FINWING TECHNOLOGY WWW FINWINGHOBBY COM PATENT PENDING...
- Page 2 Finwing Sabre Please read through the manual carefully before installation and flying This manual aims to help direct the user on how to build the Sabre RC plane. Please visit the Finwinghobby com official website for more introductions. Warning: 1 This model airplane is not a toy not recommended for children under 14 years old 2.
- Page 3 Finwing Sabre Basic information Wingspan:1900MM (74.8”) FSA01 Module1 FSA02 Module2 Hero Filming Nose Cover Gimbal Filming Nose Clear Cover Length :1320MM (52”) OPTIONS ONLY OPTIONS ONLY OPTIONS ONLY OPTIONS ONLY Propeller :11*5.5" / 11*6" Flap :Available (Options) Max.AUW :4.0kg (8.8IB) EFFICIENT AUW:3.1-3.5kg (6.8-7.7IB)
- Page 4 Finwing Sabre Wings installation Aileron: 17g Plastic Gear Servo or 23g Metal Gear Servo. Flap: 9g servo Flap is not must, Depends on your flying preference. Overview 1 > There are two slots for VTX and UHF separately on left and right wing, the purpose is to avoid signal interference especially long range flying system. please cut out the slot foam according to you equipments' size before closing the wing‐cover, Please skip if you won't put VTX and UHF on the main‐wing. For example put it on the cockpit and tail‐ boom is also no problem. it's depends on your preference.
- Page 5 2 > Prepare the extension wires first, kits package included Aileron extension wires but no extension wires for flap servos. Spreading glue to the main wing cave, unnecessary glue to the wing‐cover. Gluing time approximately 3‐4 minutes, glue will dry quickly if too long. After closing wing‐cover, it's time to install the carbon strip with a little glue, and other small parts as the photos shown. Press it firmly intermittently by the first half hour Room temperature drying about 24 hours before flying Install carbon strip with a little glue...
- Page 6 3 > Cut off the side connection of the control surface until feeling the control surface is rotatable freely Aileron, flap and Elevator all do the same Cut off the Side connection of control surface Reinforce the hinge is necessary for both sides just by the wrapping tape For example how to reinforce the bottom side, move the control surface to the max. up position, then wrapping tape adhere to the slot, press it firmly. Move the control surface to the max. down position when reinforce the top side accordingly...
- Page 7 Tips : Laminate the wing wrapping tape to laminate is more efficient and easy way to protect your airplane, but this is not the must works. Please skip if you don't want to laminate Before laminating laminated...
- Page 8 4 > Neutralize all servos, prepare to install Aileron, Flap servos , Note* flap travel is not the bigger the better, Approximately 10MM is okay Aileron Flap Aileron Flap Aileron Aileron Flap travel ≈10MM 10MM Flap Flap...
- Page 9 5 > Elevator and Rudder installation is similar to Aileron. Rudder Elevator...
- Page 10 Finwing Sabre Fuselage installation 1> Join tail‐boom to fuselage, glue to the joint contact surface then pressing firmly Don't move it at least two hours drying time at room temperature , be sure don't twist the tail‐boom ! Room temperature drying about one or two hours 2> Two hours later, install the tail carbon strips, don't forget extension wires first, and some other extension wires if you need. For example UHF or GPS extension wires Room temperature drying about one or two hours 3> install the wing‐fuselage joint parts, a little glue is necessary, A and B joint parts at correct slot Glue...
- Page 11 4> install the plywood, the motor mount will be secured to this plywood by screws Glue Glue 5> Double checking the fuselage again, be sure no parts missing !
- Page 12 6> It's time to close the fuselage, recommend glue to the right half fuselage, unnecessary glue to both half fuselage, or a little glue to the left half of fuselage is okay by some of the contact surface. Cost about 8 ‐9 minutes spreading glue to the right half of fuselage, glue will dry quickly if last too long! Pressing firmly by all part of the fuselage intermittently, especially during the first hour. Room temperature drying about 24 hours before installation of motor...
- Page 13 7> Install the following parts with glue during the period of fuselage drying Carbon Strip Recommend wrapping tape around the tail‐boom joint Magnet Please skip this if no undercarriage, hand launching only Screw washer Front gear locker Remember let the fuselage dry about 24 hours at room temperature, at this period you can install Wings , Module 2, Undercarriage etc…...
- Page 14 8 > ESC and Motor installation ESC secured to the side of fuselage, it's very good for cooling, Back to back Velcro included, cut half of the Velcro, one for ESC and another for VTX Secure the motor to the motor mount plywood by washers and screws from kits' package (included) without traditional cross shape motor mount is good to reduce the size of airplane's motor mount and produce as less air drag as possible Secure the motor mount plywood to the airplane by washers and 3 PCS long screws ( 3*35MM) Most of the Propeller should be: embed words toward the nose of airplane, don't be wrong direction !
- Page 15 Finwing Sabre Power System The following photo shown is sabre premium power system Please solder a connector for the BEC power input Connector type is depends on what type of your battery s connector The premium A ESC opto plus a external BEC 6A This combo is more safety and efficient to supply your airplane espeically &...
-
Page 16: Throttle Calibration
Finwing Sabre Power System Diagram of wires connection Advanced power system ESC type with build in UBEC SBEC 6CH Receiver For Example FINWING ESC 60A M 28 1 5 3 5 3 6 with built in BEC - S Lipo... - Page 17 Undercarriage 1> assembly the front gear as the photos shown 2> install undercarriage now, install the rear gear first, then neutralize the (23g)metal gear servo install the front gear as photos shown. Adjust the undercarriage direction correctly before flying Rear Gear Servo wire outlet E Clasp...
- Page 19 Module 2 >Secure plywood to the servo, then Secure the servo arm and the joint arm subsequently, Gear of the joint arm toward the right side as photos shown Gear >Install the Tilt module, recommend initial position as the photos shown, but you can adjust it according to your reference, you can install it more downward if you would like downward video most of the time. FYI: We also flying without rubber band and video no vibration, Anti vibration Rubber band...
- Page 20 FYI FPV Gears Layout...
- Page 21 FYI FPV Gears Layout /300 Hero Pan&Tilt system /300 Mini FPV Camera Pan&Tilt system...
Need help?
Do you have a question about the SABRE 1900 and is the answer not in the manual?
Questions and answers