Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Trodat T1511M
- Page 1 Flash Stamp Machine T1511M User Manual...
- Page 2 Trodat GmbH Linzer Straße 156 A-4600 Wels hereby declare that the Flash Stamp Machine model T1511M is CE certified respectively in conformity with the essential requirements of all relevant directives and regulations applied with the European Union. The CE certification can be requested from your Trodat sales representative.
-
Page 3: Table Of Contents
Maintenance........................ 18 VIII. Technical specification ....................18 Congratulations and thank you for your purchase of the Trodat Flash Machine T1511M. Before using the machine please read this manual to insure safe and proper operation and keep it for future reference. In case of problems or further questions please contact your Trodat sales representative. -
Page 4: General And Safety Information
Flash Stamp Machine T1511M I. General and safety information Before putting the T1511M Flash Machine into operation read this user manual carefully and keep it for future reference. The machine may only be used in closed and dry areas. Do not operate it in explosive environments. -
Page 5: Scope Of Use
Flash Stamp Machine T1511M II. Scope of use The Flash Machine T1511M is an exposure system, designed to quickly and easily expose (flash) all models and sizes of Trodat's Premium Flash range including the new (die box) and regular (foam) systems: ... -
Page 6: Delivery Content And Installation
Flash Stamp Machine T1511M III. Delivery content and installation Please check the packaging for transport damages and completeness. In case of any damage contact your supplier immediately and do not use the Flash Machine. Delivery content Flash Machine T1511M ... -
Page 7: Controls And Functions
Flash Stamp Machine T1511M IV. Controls and Functions Machine back side Power plug The power plug is located on the back of the Flash Machine. It allows the use of grounded power cables only. Fuse The fuse holder is located above the power plug. This contains the fuse that provides overload protection for the Flash Machine. - Page 8 The energy dial sets the energy level of the lamps when the exposure is activated. The energy levels are numbered "1-10", with "1" being the lowest and "10" being the highest setting. For exposing all Trodat Premium Flash models it is recommended to set the energy level at "6". Cover and clamping mechanism The clamping mechanism of the cover is for the compression of the die box or foam.
- Page 9 Flash Stamp Machine T1511M Machine open Exposure area The exposure area of the machine (150mm x 110mm) is designed to expose all MaxLight, MaxLight X, PSI, Slim Stamp and Super Slim sizes. Important: Always make sure that the exposure area is clean before flashing.
-
Page 10: Required Equipment
A regular word processing software can also be used for typesetting, but you will be unable to use the recommended Trodat typesetting templates. Please note: Trodat offers typesetting templates for all MaxLight, MaxLight X, PSI, Slim Stamp and Super Slim models and sizes as Corel Draw files. Each typesetting template consists of 3 attributes: model number, black positioning frame (outer border) and red typesetting frame (inner border) –... - Page 11 (108mm x 140mm) or US letter (216mm x 279mm). The pre-cut size perfectly fits into the T1511M Flash Machine (no extra cutting needed before putting into the machine). It is highly recommended that you use only the Trodat Premium Vellum paper. Using improper vellum can cause bad exposure results and lead to unsatisfactory stamp impression quality.
-
Page 12: Operation
Flash Stamp Machine T1511M VI. Operation All Trodat's Premium Flash models use a high quality flash foam as text plates. The foam will be sealed during the exposure process according to the artwork. Print artwork The artwork for the exposure process should be printed using a 600 dots per inch (DPI) or higher monochrome laser printer on Trodat Premium Vellum Paper. - Page 13 Flash Stamp Machine T1511M Open cover and adapt machine setup Open the cover of the machine and make sure that you have the correct machine setup depending on whether a (a) die box or (b) foam only will be exposed: (a) Exposing Die Boxes: For exposing entire die boxes remove the spacer from the cover.
- Page 14 Flash Stamp Machine T1511M Place transparency film Place one sheet of transparency film on top of the printed vellum. Ensure that the transparency sheet fully covers the vellum paper. The clear transparency film can be used from both sides. It is necessary to...
- Page 15 Flash Stamp Machine T1511M Please note: Super Slim stamps do not use an extra die box or foam. Super Slims have the foam and ink cartridge already included in the stamp and are exposed like die boxes. Just remove the dust cover (do not remove the index window) and place the complete stamp (grey foam side facing down) on the transparency film.
- Page 16 Flash Stamp Machine T1511M Remove transparency Open the clamp cover and take out the die box or foam. Remove the transparency from the exposed (a) die box or (b) foam. (a) Remove transparency from die box (b) Remove transparency from foam Please note: Exposing without transparency film is not possible.
- Page 17 Flash Stamp Machine T1511M For proper stamp assembly follow the detailed inking and assembling instructions to be found in Trodat's Premium Flash Catalogue.
-
Page 18: Maintenance
Flash Stamp Machine T1511M VII. Maintenance The Trodat Flash Machine T1511M has been designed for low maintenance operation as well as ease of use. There are regularly scheduled maintenance requirements consisting of cleaning the glass and machine body as needed. Please observe the following cleaning tips.
Need help?
Do you have a question about the T1511M and is the answer not in the manual?
Questions and answers