H.O. BOSTROM SECUREALL Adjustment Instructions

TO BE REMOVED BY THE CUSTOMER ONLY
ADJUSTMENT INSTRUCTIONS FOR THE
SECUREALL® SCBA LOCKING SYSTEM
GENERAL PRODUCT INFORMATION
FEATURES
Safely stores most U.S and International SCBA brands and sizes.
Patented auto-lock system holds the SCBA securely in place.
Patented one-touch release handle (no straps or clamps to snag).
Easy adjust components.
Meets NFPA 1901 standards and requirements of EN 1846
SAFETY INFORMATION
DANGER indicates a hazardous situation which, if not avoided, WILL result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, COULD result in a death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, COULD result in minor or moderate injury.
NOTICE is used to address practices not related to physical injury.
SAFETY INSTRUCTIONS (or equivalent) signs indicate specific safety related instructions or procedures.
SETUP AND ADJUSTMENT
AIR CYLINDER BRAND AND CYLINDER DIMENSION CHART
Identify air cylinder size before adjusting SecureALL
CYLINDER TYPE DIAMETER CIRCUMFERENCE
2216PSI ALUMINUM 6 3/4" 21 1/4"
30 MINUTE 171mm 540mm
2216PSI COMPOSITE 6 3/4" 21 1/4"
30 MINUTE 171mm 540mm
4500PSI COMPOSITE 5 3/8" 16 7/8"
30 MINUTE 137mm 429mm
4500PSI COMPOSITE 6 3/8" 20 1/8"
45 MINUTE 161mm 508mm
4500PSI COMPOSITE 6 7/8" 21 5/8"
60 MINUTE 175mm 559mm
2216PSI ALUMINUM 6 3/4" 21 1/4"
30 MINUTE 171mm 540mm
2216PSI COMPOSITE 6 5/8" 20 13/16"
30 MINUTE 168mm 529mm
4500PSI COMPOSITE 5 3/8" 16 7/8"
30 MINUTE 137mm 429mm
4500PSI COMPOSITE 6 1/2" 20 7/16"
45 MINUTE 165mm 519mm
4500PSI COMPOSITE 7'' 22"
60 MINUTE 178mm 559mm
HONEYWELL (SURVIVAIR, SPERIAN)
2216PSI ALUMINUM 6 3/4" 21 1/4"
30 MINUTE 171mm 540mm
2216PSI COMPOSITE 6 3/4" 21 1/4"
30 MINUTE 171mm 540mm
3000PSI COMPOSITE 6 3/4" 21 1/4"
30 MINUTE 171mm 540mm
4500PSI COMPOSITE 5 1/2" 17 1/4"
30 MINUTE 140mm 438mm
4500PSI COMPOSITE 6 3/8" 20"
45 MINUTE 162mm 508mm
4500PSI LO-PRO COMP 6 3/4" 21 1/4"
45 MINUTE 171mm 540mm
4500PSI COMPOSITE 7" 22"
60 MINUTE 178mm 559mm
2216PSI ALUMINUM 6 3/4" 21 1/4"
30 MINUTE 171mm 540mm
2216PSI COMPOSITE 6 5/8" 20 13/16"
30 MINUTE 168mm 529mm
4500PSI COMPOSITE 5 1/2" 17 1/4"
30 MINUTE 140mm 438mm
4500PSI COMPOSITE 6 5/16" 19 13/16"
45 MINUTE 160mm 503mm
4500PSI COMPOSITE 7" 22"
60 MINUTE 178mm 559mm
2216PSI ALUMINUM 6 3/4" 21 1/4"
30 MINUTE 171mm 540mm
2216PSI COMPOSITE 6 3/4" 21 1/4"
30 MINUTE 171mm 540mm
3000PSI COMPOSITE 6 3/4" 21 1/4"
30 MINUTE 171mm 540mm
4500PSI COMPOSITE 5 3/8" 16 7/8"
30 MINUTE 137mm 429mm
4500PSI COMPOSITE 6 3/16" 19 7/16"
45 MINUTE 157mm 494mm
4500PSI LO-PRO COMP 6 1/4" 19 5/8"
45 MINUTE 159mm 498mm
4500PSI COMPOSITE 7 1/8" 22 7/8"
60 MINUTE 181mm 581mm
5500PSI COMPOSITE 5" 15 11/16"
30 MINUTE 127mm 398mm
5500PSI COMPOSITE 6" 18 13/16"
45 MINUTE 152mm 478mm
5500PSI COMPOSITE 6 3/16" 19 7/16"
60 MINUTE 157mm 494mm
5500PSI COMPOSITE 6 7/8" 21 5/8"
75 MINUTE 175mm 549mm
2216PSI ALUMINUM 6 9/16" 21 1/8"
30 MINUTE 167mm 537mm
2216PSI COMPOSITE 6 3/4" 21 1/4"
30 MINUTE 171mm 540mm
3000PSI COMPOSITE 6 3/4" 21 1/4"
30 MINUTE 171mm 540mm
4500PSI COMPOSITE 5 3/8" 16 7/8"
30 MINUTE 137mm 429mm
4500PSI COMPOSITE 6 3/16" 19 7/16"
45 MINUTE 157mm 494mm
4500PSI LO-PRO COMP 6 1/4" 19 5/8"
45 MINUTE 159mm 498mm
4500PSI COMPOSITE 6 7/8" 21 5/8"
60 MINUTE 175mm 549mm
5500PSI COMPOSITE 5" 15 11/16"
30 MINUTE 127mm 398mm
5500PSI COMPOSITE 6" 18 13/16"
45 MINUTE 152mm 478mm
5500PSI COMPOSITE 6 3/16" 19 7/16"
60 MINUTE 157mm 494mm
5500PSI COMPOSITE 6 7/8" 21 5/8"
75 MINUTE 175mm 549mm
Table 1
H.O. BOSTROM COMPANY, INC.
818 PROGRESS AVE, WAUKESHA, WI 53186
WWW.HOBOSTROM.COM
TOOLS REQUIRED
3/16" (4.5mm) Hex Key Wrench
7/16" (11mm) wrench
1/2" (13mm) wrench
#3 Phillips Screwdriver
®
VALVE CUP CYLINDER
TOP CLAMP BOTTLE SPECIFIC SERVICE KITS
NOTCH SUPPORT
POSITION SEE PAGE 2
POSITION POSITION
AVON (ISI)
FRONT LOWER E 8902-065 KIT REQUIRED
FRONT UPPER C
FRONT UPPER A
FRONT LOWER B
FRONT LOWER C
DRAEGER
FRONT LOWER E 8902-065 KIT REQUIRED
FRONT UPPER C
FRONT UPPER A
FRONT LOWER B
FRONT LOWER C
FRONT LOWER E 8902-065 KIT REQUIRED
FRONT UPPER C
FRONT LOWER C
FRONT UPPER A
FRONT LOWER B
FRONT UPPER C
FRONT LOWER C
INTERSPIRO
REAR LOWER E 8902-065 KIT REQUIRED
REAR UPPER C
REAR UPPER A
REAR LOWER B
REAR LOWER C
MSA* M7 & G1 See page 2
FRONT UPPER E 8902-065 KIT REQUIRED
FRONT UPPER B
FRONT LOWER B
FRONT UPPER A
FRONT LOWER B
FRONT LOWER B
FRONT LOWER C
N/A UPPER A 8902-090 KIT REQUIRED
N/A UPPER B 8902-090 KIT REQUIRED
FRONT LOWER B
FRONT LOWER C
SCOTT* See page 2
FRONT LOWER E 8902-065 KIT REQUIRED
FRONT UPPER C
FRONT LOWER C
N/A UPPER A 8902-090 KIT REQUIRED
FRONT LOWER B
FRONT UPPER B
FRONT LOWER C
N/A UPPER A 8902-090 KIT REQUIRED
N/A UPPER B 8902-090 KIT REQUIRED
FRONT LOWER B
FRONT LOWER C
SECUREALL® BRACKET COMPONENTS
CLAMP ADJUSTMENT SCREWS
LOCKING NUT
®
PIVOT ARM LOCKING PLATE
WARNING LABEL
CENTER GUIDE
CYLINDER SUPPORT ASSEMBLY
VALVE CUP ATTACHMENT SCREW
SECUREALL® BRACKET ADJUSTMENT INSTRUCTIONS
1. VALVE CUP ADJUSTMENT
Standard insert 8920-068 is factory installed on all SecureALL
1
VALVE CUP ADJUSTMENT FOR INTERSPIRO ONLY
Adjustment required for Interspiro SCBA with angled valve support only: use 3/16" (4.5mm) hex key wrench to remove
attachment screw, rotate valve cup 180⁰, and reinstall screw for valve cup notch positioned rearward.
See Figure 3.
NOTCH
FRONT
2. CYLINDER SUPPORT POSITION ADJUSTMENTS
1. Measure overall SCBA cylinder length (including valve).
For SCBA's 19 1/2" (495mm) to 22 1/2" (572mm),
use upper mounting holes.
For SCBA's 22 1/4" (571mm) to 26" (660mm),
use lower mounting holes as shown in Figure 4.
2. If applicable, remove attachment screws, position cylinder
support assembly, and reinstall screws.
2
WARNING
The installer is liable for SCBA bracket adjustment. Failure to properly tighten fasteners could
result in cylinder support coming loose unexpectedly and accidental SCBA release.
3. TOP CLAMP ADJUSTMENT
1. Measure the circumference of the SCBA bottle and refer to Table 1 for Top Clamp Position.
2. Place valve in foot cup and push bottle into SecureALL.
3. Use 3/16" (4.5mm) hex key wrench to remove clamp adjustment screws and slide clamp inward or outward
to find the correct fit. See Figure 5. Note that the bottle should have some freedom to move.
4. Replace and tighten adjustment screws in the appropriate clamp adjustment holes.
5. Remove and reinstall the SCBA assembly to confirm adjustment for cylinder size. Ensure there are no
obstructions that could prevent the cylinder from locking up against the clamp.
3
WARNING
Installer is liable for SCBA bracket adjustment. Failure to properly tighten fasteners could result
in clamp sliding forward and accidental SCBA release.
TOP CLAMP
QUICK HEIGHT ADJUSTMENT LEVER
LATCH ASSEMBLY
ALUMINUM MOUNTING CHANNEL
CENTER GUIDE ADJUSTMENT SCREWS
CYLINDER SUPPORT ATTACHMENT SCREWS
VALVE CUP (OPTIONS AVAILABLE)
Figure 1
brackets. See Figure 2.
®
Figure 2
REAR
Figure 3
Figure 4
®
Figure 5
NOTICE: For additional assistance contact your OEM, dealer OR
the H.O. Bostrom sales department at sales@hobostrom.com;
(800) 332-5415 OR (262) 542-0222, Option 2
See Page 2
UPPER
LOWER
A
B
C
D
E
08-0125PRINT Rev 01 5/2/19