San-Ei K87310J-BW Installation Instructions Manual

Single handle kitchen faucet

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

For safety and easy faucet replacement, San-Ei recommends the use of

the following helpful tools:

SAFETY GLASSES

ADJUSTABLE WRENCH

Keep Instructions for Future Reference

Thank you for purchasing San-Ei's quality faucet.

With simple care and maintenance, it will provide you with many years of reliable

performance.

Please read instructions before installation.

TIPS FOR REMOVAL OF OLD FAUCET

CAUTION: Always turn water OFF before removing existing faucet or

disassembling the faucet.

Open the faucet handles to relieve water pressure and ensure that

complete water shut-off has been accomplished.

(Complies with ASME A112.18.1 and CSA B 125)

T o o l s

PIPE WRENCH

BASIN WRENCH

PHILLIPS SCREWDRIVER

A b o u t T h i s M a n u a l

- 1 -

INSTALLATION INSTRUCTIONS

K87310J-BW

SINGLE HANDLE

Kitchen Faucet

PLIERS

CHANNEL LOCKS

BW-OED

FLASHLIGHT

Table of Contents

Need help?

Do you have a question about the K87310J-BW and is the answer not in the manual?

Questions and answers

Summary of Contents for San-Ei K87310J-BW

Page 1 BW-OED INSTALLATION INSTRUCTIONS K87310J-BW SINGLE HANDLE Kitchen Faucet T o o l s For safety and easy faucet replacement, San-Ei recommends the use of the following helpful tools: SAFETY GLASSES PIPE WRENCH PLIERS CHANNEL LOCKS ADJUSTABLE WRENCH BASIN WRENCH PHILLIPS SCREWDRIVER...
Page 2 The others become the production that receives. Ivory As for the order, please attach the color number Green Black at the end of the article No. R104-14X-(Color)-BW K87310J-BW General Description 1. Cap 2. Lever 3. Coil Spring 4. Lever Support R104-10X-(Color)-BW 5.
Page 3 O P E R A T I O N Kitchen Faucet K87310J-BW 9-2/5"(240mm) K87310J-BW 1/2-14 NPSM MAX 3-3/10"(85mm) Water Bucket (Not supplied) NOTE : Maximum deck thickness for installation is 1-1/5"(30mm). Hole size for installation is between 1-2/5"(36mm) to 1-1/2"(38mm).
Page 4 I N S T A L L F A U C E T Sink hole dia Between 1-2/5"(36mm) 1-1/5"(30mm) to 1-1/2"(38mm) (Caution !) Remove a protective tape attached in the back of the packing. Then, install the faucet body to be fixed. Seat Protective Packing...
Page 5 2. Install faucet The front side of the spout should face you. Then, make tightening the lock nut(15). (counterclockwise) Please don't forget to put a seat packing(12), rubber packing(13), and metal washer(14), between unit body(11) and lock nut(15). 3. Install "quick fastener" adapter Please install the adapters(19) onto the each stop valves(not supplied).
Page 6 C A R T R I D G E R E P L A C E M E N T The cartridge Holder is a feretory. A special tool is set in the ditch of the cartridge Holder. Special tool Ditch A special tool is placed with the At assembly...
Page 7 F L U S H I N G I N S T R U C T I O N S IMPORTANT! : Pipe chips, sand, stones and other solid found in new and renovated plumbing can damage the cealing of the cartridge and cause leaks to avoid damage, DO NOT TURN ON SUPPLY VALVES until instructed below.
Page 8 This shall be the sole remedy available under this warranty. Defects or damage caused by the use of other than genuine SAN-EI parts are not covered by this warranty. Installation or any other labor charges associated with the repair or re-installation of SAN-EI products is not covered by this warranty.