Related Manuals for FLATLIFT EXTRA FLAT
Summary of Contents for FLATLIFT EXTRA FLAT
- Page 1 Operating Manual P.01 O u t p e r f o r m . O u t l a s t . Well thought-out space-saving!
-
Page 2: Table Of Contents
Operating Manual CONTENTS P.02 CONTENTS O u t p e r f o r m . O u t l a s t . C.01 INTRODUCTION C.02 FEATURES C.03 PRODUCT DIMENSIONS C.04 INITIAL PRODUCT SET UP Set-up P.06 Images P.07 C.05 PRODUCT CONTROL Programming the remote control (S435) -
Page 3: Introduction
The product will be damaged if it is dropped, even from a low height. Before using the product for the first time, please check that the free raising and lowering of the Flatlift including the mounted TV equipment is possible and ensure a collision-free run. -
Page 4: Features
Connection to room control system possible (refer to P.09 image 5) Automatic TV switch-off (optional) Millimetre-exact programming of the stopping point (optional) 230V emergency power supply (optional) Scope of supply: Flatlift Extraflat 43“ / 50“ Control box 230V power cord Motor cable 12V wall power supply for the receiver 433.92 MHz 2 channel receiver... -
Page 5: Product Dimensions
Operating Manual PRODUCT DIMENSIONS C.03: P.05 PRODUCT DIMENSIONS O u t p e r f o r m . O u t l a s t . -
Page 6: Initial Product Set Up
5. Connect the wall power supply of the receiver (image 2, no. 4) with the power cord (P.07, image 5) to the mains supply. 6. Now initialise the Flatlift by pressing down the ‘Down’ key on the controller (P.07 image 6 no. 9) for 2 x 5 sec. After this, extend and retract your Flatlift fully twice over. - Page 7 Operating Manual INITIAL PRODUCT SET U C.04: P.07 INITIAL PRODUCT SET UP O u t p e r f o r m . O u t l a s t . Image 3 Image 5 Image 4 Image 6...
-
Page 8: Product Control
O u t p e r f o r m . O u t l a s t . Programming the remote control (S435): You can also get additional remote controllers for your Flatlift system (optional extra). As the controllers are coded, you have to programme them. -
Page 9: Resetting The Receiver
Image 3 Image 4 Connection to a room control system: You can connect your Flatlift to a room contro l system (image 5) if this system has 2 relay outputs with potential free contacts. These relays must be actuated for a programmable time period. - Page 10 Different lid closing solutions are available depending on the reali- sation of the project (image 1). The A/V installer which is ins- talling the Flatlift thus enjoys flexibility and can also change the lid solution again at a later time. When the Flatlift retracts, the cover closes softly thanks to the spring dampened hinges.
- Page 11 O u t p e r f o r m . O u t l a s t . Image 3 Lid variation 2: In this version, the lid goes up with the Flatlift and rests on the top of the TV set. This variation is known as the ‚floating top‘ version.
-
Page 12: Product Integration
Flatlift. This variant is similar to lid version 2 (refer to P.11, image 3). When Image 5 the Flatlift is fully retracted, the lid is flush with the rest of the top of the unit. -
Page 13: Recommanded Installion
TV set: Lift height, Flatlift = 965 mm - 3 x 10 mm min. clearance - (12 to 19 mm) thickness of the cover, = 916 mm 916mm = max. height of TV... - Page 14 The same thing applies to the TV. If the TV height is less than 940 mm, then you can also place the Flatlift on a platform which is the same height as the resulting height difference to the upper edge of the sofa min.
-
Page 15: Trouble Shooting
The motor cables must be connected starting at port 1 and going up Is there any evidence of damage to the cables, the control box, the remote control or the Flatlift? S Damaged components must be exchanged. Please contact us. -
Page 16: Legal Notice
Fax.: +49 (0) 62 41 97 20 12 info@fl atlift.de www.fl atlift.de Hours of business: Mon-Fri. 7:30 am- 5:30 pm Managing Director: Sascha Rissel HRA Mainz: HRB 40436 USt. (VAT) ID: On request Status of document: JULY 2008 © 2008 FLATLIFT TV LIFT SYSTEME GMBH...