Sealey PTJ30 Instructions

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to wear eye
instructions protection
1. safety
WarninG! ensure all preliminary checks are carefully carried out before use of jack. immediately repair or replace damaged parts (use
‰
authorised service agent). ensure use of genuine parts only. non authorised parts may be dangerous and will invalidate the warranty.
WarninG! use jack on level and solid ground, preferably concrete.
‰
▲ DanGer! Do not use on tarmacadam, or any other soft surface as jack may sink or topple. serious personal or fatal injury may result.
▲ DanGer! if jack tips or leans stop what your are doing. moVe QuicKly to a safe distance. do not try to hold or
steady JacK. serious personal or fatal injury may result.
use jack in an adequate working area for its function, keep area clean & tidy and free from unrelated materials.
9
ensure there is adequate lighting.
9
Before use ensure the gearbox weight and size does not exceed the capacity of the jack.
9
ensure the vehicle is raised and stabilised at the correct height before attempting to move the jack under the vehicle.
9
Keep all unauthorised persons away from the jack during lifting and lowering and when in transit.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non slip shoes.
9
remove ill fitting clothing. remove ties, watches, rings, and other loose jewellery, and contain and/or tie back long hair.
9
WarninG! ensure load is placed level and centrally on jack saddle and load is fixed in place before attempting to lift, lower, or transport.
‰
the lowering speed will vary according to the weight of the load and the release valve setting.
9
diligence is required in ensuring that you continually monitor any operation until completed.
9
Do not exceed the rated capacity of the jack.
8
Do not allow untrained persons to operate the jack.
8
Do not place any part of your body within or under the jack during use.
8
Do not raise or lower vehicle lifting platform whilst the transmission jack is being used.
8
Do not transport the jack, with or without a load, with the saddle in the raised position.
8
Do not get jack wet or use in damp or wet locations or areas where there is condensation.
8
Do not operate the jack when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
Do not lift or support vehicles with jack and do not use jack as a load sustaining device.
8
Do not use jack for any purpose other than removal, transportation, installation of transmissions.
8
Do not move jack without suitable restraint on the load.
8
Do not make any modifications to the jack, and do not adjust or tamper with safety valve.
8
Do not remove any labels from the jack. if labels are damaged or unclear replace them.
8
use a qualified person to lubricate and maintain the jack.
9
Do not use brake fluid to top up hydraulic unit. use sealey hydraulic oil only.
8
lower saddle to the lowest position before storing in safe area, ensure all parts are clean, free of grease and oil.
9
2. introDuction
professional transmission jack with foot pedal operation for raising and lowering, leaves hands free for other related tasks. provides a smooth,
controlled lowering of the load with dead man's principal preventing accidental operation. nylon wheels for smooth and quiet manoeuvring,
also limits damaage to garage floors Includes patented 2-in-1 saddle that, when reversed, acts as a high density foam jacking pad. handle
incorporates tray for fasteners and tools. suitable for workshop use or by the serious motoring enthusiast.
3. specification
model No........................................PTJ30..............................PTJ75..............................PTJ120
capacity.........................................300Kg...............................750Kg..............................1200Kg
ram Extensions......................................1.......................................1........................................1
minimum Saddle Height...............1140mm...........................1110mm.............................1110mm
maximum Saddle Height..............1990mm...........................1930mm............................1925mm
Base Size...............................720x720mm...............720mmx720mm.......................720x720mm
fixed/adjustable saddle...................fixed................................fixed..................................fixed
weight...............................................22Kg.................................30Kg..................................32Kg
© Jack sealey limited
instructions for
premier transmission jack 0.3, 0.75,
1.2tonne vertical
model no:
wear protective wear safety
gloves footwear
Original Language Version
ptj30, ptj75, ptj120
wear protective
clothing
pTJ30,PTJ75,PTJ120 | Issue 1 16/08/16