Hinkley 51000 BZ Installation Instructions

Family: 120v series small well light

Advertisement

Drawing 1 - Lamp Installation
D
H I N K L E Y L I G H T I N G
installation instructions
Family: 120V Series Small Well Light
1. Find a clear area in which you can work.
2. Carefully review instructions prior to assembly.
3. Gather tools required: WIRE STRIPPERS, PHILIPS HEAD SCREWDRIVER,
B
SILICONE GREASE, THREAD SEALANT.
C
• Save these instructions for future reference.
WARNING: LUMINAIRE MUST BE INSTALLED AND GROUNDED IN ACCORDANCE
WITH THE NATIONAL ELECTRICAL CODE (NEC) AND LOCAL CODES. FOR PORTABLE
STAKE OR SUFACE MOUNT USING A CORD AND PLUG, THE LUMINAIRE MUST BE
PLUGGED INTO A RECEPTACLE PROTECTED BY A GROUND FAULT CIRCUIT
INTERRUPTER (GFI). FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY
AND/ OR DAMAGE TO THE LUMINAIRE.
ALWAYS USE UL RECOGNIZED WIRE CONNECTORS FOR CONNECTIONS.
SAFETY WARNING: LUMINAIRE CAN BECOME VERY HOT DEPENDING ON THE
LAMP WATTAGE USED. LENS AND HOUSING AROUND THE LAMP CAN BECOME
HOT ENOUGH TO BLISTER HANDS. PARTICULAR CARE SHOULD BE TAKEN NOT TO
LOCATE LUMINAIRES WHERE SMALL CHILDREN CAN REACH THEM IF HIGH
WATTAGE LAMPS ARE USED.
IN GROUND LUMINAIRE IS ETL LISTED FOR BELOW GRADE INSTALLATION ONLY.
1. Please refer to the mounting instructions located on the back of this sheet to
continue installation of this fixture.

lamp installation replacement

1. To prevent electrical shock, disconnect from the electrical supply before servicing.
2. Loosen the cover screws (B) and remove cover (C).
3. Remove lens with gasket assembly (D) to expose lamp.
4. Replace lamp with correct wattage and type marked on fixture label.
CAUTION: DO NOT EXCEED MAXIMUM WATTAGE MARKED ON LUMINAIRE LABEL.
5. Clean the gasket (D) and gasket channel.
6. Re-install gasketed lens and cover (C), follow by tightening the screws (B) evenly.
MAINTENANCE NOTE: TO ASSURE PROPER OPERATION AND EFFICIENCY AND TO
PREVENT LUMINAIRE OVERHEATING, LENS MUST BE KEPT CLEAN AND FREE OF
DIRT, LEAVES, TRASH, AND MINERAL DEPOSITS FROM WATER. A REGULAR
SCHEDULE MAINTENANCE PROGRAM IS RECOMMENDED.
Info 51000 BZ: Lamp Type is R20, R30, R40, PAR20, PAR30, PAR 38, Incandescent
12600 Berea Road
C leveland, OH 44111
st ar t here
Maximum Wattage is 100 watts per bulb.
8 00 . 446 . 553 9 / 21 6. 67 1. 33 00
Item No. 51000 BZ
w w w. hi nk l e yl ig ht i n g . c o m
3.4.08

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 51000 BZ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hinkley 51000 BZ

  • Page 1 PREVENT LUMINAIRE OVERHEATING, LENS MUST BE KEPT CLEAN AND FREE OF DIRT, LEAVES, TRASH, AND MINERAL DEPOSITS FROM WATER. A REGULAR SCHEDULE MAINTENANCE PROGRAM IS RECOMMENDED. Info 51000 BZ: Lamp Type is R20, R30, R40, PAR20, PAR30, PAR 38, Incandescent 3.4.08 Maximum Wattage is 100 watts per bulb.
  • Page 2 2. If you are using an HID self reflector lamp in the luminaire an integrated ballast must be used. Ask your local Hinkley Lighting representative or visit www.hinkleylighting.com for information. 3. Dig hole approximately 16” deep by 15” in diameter - see Drawing 2.

Table of Contents