Acuity 247 Series Installation Instructions

POST TOP LUMINAIRE 247 SERIES & TCL FULL CUTOFF (FC)
DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.
HOUSING MUST BE GROUNDED TO REDUCE POTENTIAL OF ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION,
CUPOLA LENS CUPOLA LENS
ADJUST PHOTO- ADJUST PHOTO-
CONTROL BY LIFTING CONTROL BY LIFTING
& TURNING CUPOLA & TURNING CUPOLA
SIMULTANEOUSLY SIMULTANEOUSLY
HOOD HOOD
TRIGGER TRIGGER
LATCH LATCH
-OPTIONAL- -OPTIONAL-
NEMA NEMA
LABEL HERE LABEL HERE
-OPTIONAL- -OPTIONAL-
LADDER REST (2) LADDER REST (2)
-OPTIONAL- -OPTIONAL-
SET SCREWS (3) SET SCREWS (3)
FIGURE 1 FIGURE 1
CLOSED HOOD - STREE CLOSED HOOD - STREET T SIDE VIEW
FIGURE 2 FIGURE 2
OPEN HOOD - TOP VIEW OPEN HOOD - TOP VIEW
DRAWING NO. A72084 REV -- (FRONT)
American Electric Lighting a division of Acuity Lighting Group, Inc. Granville, OH
INSTALLATION INSTRUCTIONS
WARNING
!
WARNING
!
CAUTION
!
CONSULT LOCAL CODE AUTHORITY
CUPOLA CAP CUPOLA CAP
CUPOLA BASE CUPOLA BASE
LAMP SOCKET LAMP SOCKET
LOCATED WITHIN LOCATED WITHIN
HOOD HOOD
CLOSURE CLOSURE
SCREW SCREW
BOSS BOSS
COVER COVER
LOWER HOUSING LOWER HOUSING
MIN POLE OD 2.375" MIN POLE OD 2.375"
MAX POLE OD 3" MAX POLE OD 3"
SIDE VIEW
LOWER LOWER
HOUSING HOUSING
COVER COVER
CAPTIVE CAPTIVE
SCREW FOR SCREW FOR
COVER COVER
©2008 ACUITY LIGHTING GROUP, INC.
OPENING & CLOSING THE HOOD: OPENING & CLOSING THE HOOD:
1 1 . . TO OPEN THE FIXTURE HOOD, LOCATE THE CLOSURE SCREW TO OPEN THE FIXTURE HOOD, LOCATE THE CLOSURE SCREW
LOCATED ON THE STREET SIDE OF THE FIXTURE. (SEE LOCATED ON THE STREET SIDE OF THE FIXTURE. (SEE
FIGURE 1.) FIGURE 1.)
2. UNSCREW THE CAPTIVE CLOSURE SCREW. YOU WILL 2. UNSCREW THE CAPTIVE CLOSURE SCREW. YOU WILL
KNOW KNOW T THE SCREW HE SCREW IS IS COMPLETELY DISENGAGED FROM COMPLETELY DISENGAGED FROM
THE HOOD WHEN THE HOOD WHEN THE SCREW CAN MOVE FREELY UP AND THE SCREW CAN MOVE FREELY UP AND
DOWN. DOWN.
3. OPEN THE HOOD. 3. OPEN THE HOOD.
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE HOOD AND RE- 4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE
TIGHTEN THE CAPTIVE CLOSURE SCREW. TIGHTEN THE CAPTIVE CLOSURE SCREW.
NOTE FOR OPTIONAL TRIGGER LATCH: TO OPEN THE UNIT NOTE FOR OPTIONAL TRIGGER LATCH: TO OPEN THE UNIT
SIMPLY PULL TRIGGER SIMULTANEOUSLY WITH YOU SIMPLY PULL TRIGGER SIMULTANEOUSLY WITH YOUR R INDEX
FINGER WHILE FINGER WHILE PUSHING UP ON THE HOOD WITH YOUR PUSHING UP ON THE HOOD WITH YOUR THUMBS.
CLOSE THE UNIT BY CLOSE THE UNIT BY CLOSING THE HOOD AND PRESSING CLOSING THE HOOD AND PRESSING DOWN
UNTIL THE TRIGGER LATCH ENGAGE. UNTIL THE TRIGGER LATCH ENGAGE.
FULL CUTOFF COVER REMOVAL & INSTALLATION: FULL CUTOFF COVER REMOVAL & INSTALLATION:
1. UNSCREW THE CAPTIVE SCREW LOCATED ON TOP OF THE 1. UNSCREW THE CAPTIVE SCREW LOCATED ON TOP OF THE
COVER. COVER.
2. REMOVE COVER AND DISCONNECT MOLEX CONNECTIONS. 2. REMOVE COVER AND DISCONNECT MOLEX CONNECTIONS.
NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED
AGAINST THE CASTING DURING RE-INSTALLATION OF THE AGAINST THE CASTING DURING RE-INSTALLATION OF THE
COVER. COVER.
HOOD AND RE-
INDEX
THUMBS.
DOWN
PART NUMBER 057-71-72084