Related Manuals for MotionRC Detrum GAVIN-6C
Summary of Contents for MotionRC Detrum GAVIN-6C
- Page 1 Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Version 1.0...
-
Page 2: Table Of Contents
Program Servo Range of Motion ..................8 Program Servo Sub Trim ....................9 Program Expo ........................9 Program Dual Rates ....................... 11 Set Timers ........................13 Perform a Range Test ....................14 Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter... -
Page 3: Review The Transmitter's Controls
This guide provides instructions to help you program the Detrum GAVIN-6C for an airplane. Additional information can be found in the manual included with the radio. Review the Transmitter’s Controls 1. Power switch—push the switch up to turn the transmitter on. -
Page 4: Review The Home Screen
11. DOWN button—use this to highlight options on the screen. 12. EXT button—press this to move back to the previous screen. 13. ENT button—press this to select a highlighted menu option. You also use it to enter Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Page 2... -
Page 5: Power The Transmitter
2. Use the UP or DOWN buttons to highlight Model Set and press the ENT button. 3. Use the UP or DOWN buttons to highlight Model and press the ENT button. Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Page 3... - Page 6 10. Repeat steps 8 and 9 to complete the model name. You can choose the space character to “erase” an existing character. 11. Press ENT to save the new name. 12. Highlight Type and press ENT. Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Page 4...
-
Page 7: Bind A Receiver To A Model
4. Highlight the model you want to bind to the receiver and press ENT. The model you selected becomes active. 5. Press EXT twice to move back to the home screen. Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Page 5... -
Page 8: Prepare To Program An Airplane
8. Check to make sure a spinning prop or EDF won’t be a safety hazard and move the HOLD switch to the up position to enable the throttle. Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Page 6... -
Page 9: Program Servo Direction
3. Select the channel for the control surface (such as CH2 for the elevator), and press the R/+ button. The direction setting changes from Norm to Rev and the servo moves in the opposite direction. Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Page 7... -
Page 10: Program Servo Range Of Motion
6. Repeat steps 2-5 until you have set the range of motion for all of the channels you are using. 7. Press EXT three times to move back to the home screen. Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Page 8... -
Page 11: Program Servo Sub Trim
“twitchy” (meaning that it is overly sensitive). With positive expo, the plane doesn’t react as quickly to stick movements near their centers, which is Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Page 9... - Page 12 3. Press the R/+ button to increase the amount of expo or L/- to decrease it. As you apply expo, the graph on the right side of the screen shows the amount of expo applied. (To remove expo, select RESET and press R/+ or L/-.) Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Page 10...
-
Page 13: Program Dual Rates
Because the FLAP switch is a two-position switch, it is useful for dual rates (if a model has flaps, put them on the FMOD switch because it is a three-position switch). Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Page 11... - Page 14 5. Press EXT three times to return to the home screen. 6. Make sure you know which direction of the switches you selected in steps 2, 3, and 4 Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Page 12...
-
Page 15: Set Timers
The most common control is the THR (throttle) so that the timer measures the amount of time the throttle is applied. You can also choose either position Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Page 13... -
Page 16: Perform A Range Test
If not, you need to re-position the receiver or antennas and repeat the range test until it passes. 5. Press EXT to exit the range test mode. Motion RC Supplemental Guide for the Detrum GAVIN-6C Transmitter Page 14...
Need help?
Do you have a question about the Detrum GAVIN-6C and is the answer not in the manual?
Questions and answers